American Standard Double Bowl 7160.803 Specification Sheet

DOUBLE BOWL DUAL LEVEL KITCHEN SINK
• Acid-resisting enameled steel
• Dual level, double bowl design
• Self-rimming installation
• Shown with 4205.660 Silhouette faucet
(not included)
• Silicone sealant supplied
• Available in 3, 4, or 5 faucet hole
configuration
7160.803 3 hole
7160.804 4 hole
7160.805 5 hole
Nominal Dimensions: 838 x 559 x 184mm
(33" x 22" x 7-1/4")
Bowl sizes:
Large Bowl: 527mm (20-3/4") wide, 413mm
(16-1/4") front to back 178mm (7") deep
Small Bowl: 187mm (7-3/8") wide, 413mm
(16-1/4") front to back 146mm (5-3/4") deep
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.4M for Enameled Steel Plumbing
Fixtures
To Be Specified
Color: (specify White Heat or Bone)
Faucet*: (specify finish)
Basket Strainer: 4331.013 (Chrome only)
Soap Dispenser*: 4503.115 (specify color)
Trap:
* See faucet section for additional models available
4/98
51mm (2)
OPTIONAL
206mm
(8-1/8)
311mm
(12-1/4 )
7160.805
5 HOLE
89mm
(3-1/2)
DIA.
38mm (1-1/2)
RAD. TYP.
13mm
(1/2) SEALING
COMPOUND
171mm
(6-3/4)
146mm
(5-3/4)
1-1/2 O.D. TAILPIECE
914mm (36)
SUGGESTED COUPLING NUTS
FINISHED FLOOR
FAUCET
CERAMIX
RELIANT
TOP MOUNT
HERITAGE
AMARILIS
BOTTOM MOUNT
NOTES:
COUNTERTOP CUTOUT 800 X 521MM WITH 19MM RADIUS (31-1/2 X 20-1/2
WITH 3/4" RAD.) AT CORNERS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP
SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range
of tolerances established by ANSI Standard Z124.6
These measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided leaflet.
© 1998 American Standard Inc.
DOUBLE BOWL
DUAL LEVEL SINK
102mm
FINISHED WALL
102mm
(4)
OR SPLASHBACK
(4) 102mm
(4)
C/L
102mm(4)
133mm
(5-1/4)
432mm
267mm
(17)
(10-1/2)
838mm
(33)
203mm
(8)
COUNTERTOP
3/8 O.D.
BENDABLE
TUBING
21mm
ON FITTING
(13/16)
MAX.
CLAMPING DETAIL
7160.803 7160.804
2021.700 2021.741 —
4205.241 4205.217 —
6270.000 6279.000 44mm(1-3/4)
7270.SER. 7271.SER. 95mm(3-3/4)
ENAMELED STEEL
38mm (1-1/2)
DIA. HOLES TYP.
54mm
(2-1/8)
7160.804
4 HOLE
559mm
(22)
*
CUTOUT NOTE
COUNTERTOP
(BY OTHERS)
X
140mm
(5-1/2)
Y
146mm
(5-3/4)
LUG AND
SCREW
ASSEMBLY
X Y
327mm(12-7/8)
254mm(10)
—
—
KSS-014