Download  Print this page

American Standard Bathroom Faucet Troubleshooting Manual

Single control lavatory faucet with pop-up drain.
Hide thumbs
   

Advertisement

Speed Connect™ Drain

Troubleshooting Guide

If sink does not hold water even though Stopper is in the "down" position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for "Unlocked" mode.
CABLE ADJUSTMENT PROCEDURE
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
"Cam" in the illustration. Fig. B.
Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position. Fig. B, C.
Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
Fig. A.
1
RE-ATTACH
DISCONNECT
2
STOPPER REMOVAL PROCEDURE
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as "Cam" and "Cam Cap" in the illustration. Fig. B.
Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
The Stopper can now be removed by lifting it out of the Drain. Fig. F.
Fig. D.
CAM CAP
Fig. E.
REMOVE
CAM CAP
Fig. B.
Fig. C.
CAM
STOPPER
REMOVE
CAM
5
DOWN
1
Fig. F.
5 1 3 1 4 R e v . 1 . 3

Advertisement

Table of Contents

   Related Manuals for American Standard Bathroom Faucet

   Summary of Contents for American Standard Bathroom Faucet

  • Page 1: Troubleshooting Guide

    Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: •...
  • Page 2: Stopper Installation Procedure

    To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.
  • Page 3: Product View

    023529-0070A CARTRIDGE KIT M962527-YYY0A POP-UP ROD 909719-YYY0A SPOUT ESCUTCHEON A912699-0070A RUBBER RING M962541-0070A MOUNTING KIT 060277-YYYOA ESCUTCHEON KIT 066116-YYY0A DRAIN STOPPER 066117-YYY0A M953450-YYY0A 2" FLANGE KIT COMPLETE DRAIN ASSEMBLY 060276-YYY0A LIFT ROD 072574-0070A EXTENSION ROD 066118-0070A PIVOT ROD KIT 070847-0070A CLIP M961711-0070A TAILPIECE INSERT...

This manual is also suitable for:

Jasmine 3808.101

Comments to this Manuals

Symbols: 0
Latest comments:
  • Sharon Jan 21, 2017 07:18:
    Thank you SO much for putting this online! It was a tremendous help!