Subscribe to Our Youtube Channel
Related Manuals for Pulsar V041
Summary of Contents for Pulsar V041
- Page 1 CAL. V011, V041 ALARM CHRONOGRAPH Analogue time and digital time/calendar Regular alarm Stopwatch Illuminating light (for Cal. V011)
- Page 2 DISPLAY AND CROWN/BUTTONS CROWN With each press of button A, the digital display changes as follows: TIME/CALENDAR ALARM display CALENDAR display SETTING display STOPWATCH display TIME display...
-
Page 3: Screw Down Crown
SCREW DOWN CROWN [for models with screw down crown] Unlocking the crown 1 Turn Crown counterclockwise until you no longer feel the threads turning. 2 Crown can be pulled out. Locking the crown 1 Push Crown back in to normal position. 2 Turn Crown clockwise while pressing it lightly until tight. -
Page 4: Digital Time/Calendar Setting
DIGITAL TIME/CALENDAR SETTING Press to show TIME/CALENDAR SETTING display. Select the digits to be adjusted. Set the flashing digits. Press to show TIME/CALENDAR SETTING display. Press to show CALENDAR display. Selection of the digits Seconds Minutes Hour TIME/CALENDAR SETTING display Month Date 12-/24-hour indication... -
Page 5: Analogue Time Setting
ANALOGUE TIME SETTING Be sure to set the digital time first before setting the analogue time. CROWN 1 Pull out when Second hand is at the 12 o’clock position. 2 Turn to set Hour and Minute hands. 3 Push back when the seconds in the digital time display count “00”. - Page 6 ALARM ALARM TIME SETTING Press to show ALARM display. Press to activate the alarm setting function. Select the digits to be adjusted. Set the flashing digits. Press to show ALARM display. ALARM display mark Selection of the digits ALARM display Hour Minutes...
- Page 7 ENGAGEMENT/DISENGAGEMENT OF ALARM AND HOURLY TIME SIGNAL Press to show CALENDAR or TIME display. With each simultaneous press, alarm and hourly time signal are engaged and disengaged in order: Both engaged Alarm disengaged Hourly time signal engaged Hourly time signal mark Alarm engaged Alarm mark Hourly time signal disengaged...
- Page 8 STOPWATCH The stopwatch measures up to 60 minutes in 1/100 second increments. Press to show STOPWATCH display. Start. Stop. Reset. Minutes 1/100 seconds Seconds...
-
Page 9: Notes On Operating The Watch
NOTES ON OPERATING THE WATCH DIGITAL TIME/CALENDAR SETTING When setting the flashing digits, they are advanced quickly by keeping button A pressed, except the seconds and 12-/24-hour indication. Seconds digits setting: The seconds are reset to “00” by pressing button A. * When the seconds count any number from “30”... - Page 10 ANALOGUE TIME SETTING When setting the minute hand, first advance it 4 to 5 minute ahead of the desired time and then turn it back to the exact minute. When the crown is pushed in, the minute hand may move slightly. However, this is not a malfunction.
-
Page 11: Battery Change
When the battery expires, be sure to replace it as soon as possible to prevent any malfunction. We recommend that you contact an AUTHORIZED PULSAR DEALER for battery replacement. - Page 12 WARNING Do not remove the battery from the watch. If it is necessary to take out the battery, keep it out of the reach of children. If a child swallows it, consult a doctor immediately. Never short-circuit, tamper with or heat the battery, and never expose it to fire.
-
Page 13: To Preserve The Quality Of Your Watch
WATER RESISTANCE Non-water resistant • If the watch becomes wet, have it checked by an AUTHORIZED PULSAR DEALER or SERVICE CENTER. Water resistant 5/10/15/20 bar • Do not operate the crown or buttons when the watch is wet or in water. - Page 14 Care should also be taken on diving into water. ** We recommend that you wear a PULSAR Diver’s Watch for scuba diving. TEMPERATURES MAGNETISM...
-
Page 15: Periodic Check
2 to 3 years. Have Years watch or hit it against hard your watch checked by an surfaces, as this may AUTHORIZED PULSAR cause damage. DEALER or SERVICE CENTER to ensure that the case, crown, buttons, gasket and crystal seal remain intact. -
Page 16: Static Electricity
. P l e a s e c o n t a c t y o u r AUTHORIZED PULSAR DEALER or SERVICE CENTER if you wish to have a...
Need help?
Do you have a question about the V041 and is the answer not in the manual?
Questions and answers