Related Manuals for Pulsar VD50
Summary of Contents for Pulsar VD50
- Page 1 CAL. VD50 1/10 SECOND RETROGRADE CHRONOGRAPH TIME/CALENDAR l Hour, minute and second hands l Date displayed in numerals STOPWATCH l Measures up to 60 minutes in 1/10 second increments.
- Page 2 SCREW DOWN CROWN DISPLAY AND CROWN/BUTTONS [for models with screw down crown] Unlocking the crown STOPWATCH 1/10-second hand 1 Turn Crown counterclockwise until you no longer feel the threads turning. Minute hand Hour hand 2 Crown can be pulled out. STOPWATCH minute hand Locking the crown CROWN 1 Push Crown back in to normal position. 2 Turn Crown clockwise while pressing it Date lightly until tight.
-
Page 3: Time/Calendar Setting
ADJUSTING THE STOPWATCH HAND POSITION TIME/CALENDAR SETTING Before setting the time, be sure to check that the STOPWATCH hands are in the “0” position when the stopwatch is reset. (For resetting the stopwatch, see Minute hand "STOPWATCH".) Second hand * If any of the STOPWATCH hands do not return to the "0" position when the stop- watch is reset, follow the procedure below to reset the hands. Hour hand STOPWATCH Pull out to second click. CROWN 1/10-second hand Press repeatedly to reset the STOPWATCH 1/10 second Date hand to the “0” position. CROWN 1 Pull out to first click, and turn clockwise until the previous day’s date Press repeatedly to reset the appears. - Page 4 STOPWATCH Standard measurement l The stopwatch can measure up to 60 minutes in 1/10 second increments. l The measured time is indicated by the STOPWATCH hands that move inde- START STOP RESET pendently of the center hands. l Before using the stopwatch, be sure to check that the crown is set at the nor- Accumulated elapsed time measurement mal position and that the STOPWATCH hands are reset to the “0” position. * If the STOPWATCH hands do not return to the "0" position when the stopwatch is reset, follow the procedure in "ADJUSTING THE STOPWATCH HAND POSITION" to reset the hands.
-
Page 5: Notes On Operating The Watch
When setting the minute hand, first advance it 4 to 5 minutes ahead of the desired NOTES ON OPERATING THE WATCH time and then turn it back to the exact minute. ADJUSTING THE STOPWATCH HAND POSITION STOPWATCH The STOPWATCH minute hand moves correspondingly with the STOPWATCH sec- Restart and stop of the stopwatch can be repeated by pressing button A. ond hand. The STOPWATCH hands move quickly if the respective buttons are kept pressed. BATTERY CHANGE TIME/CALENDAR SETTING It is necessary to adjust the date on the first day after a 30-day month and February. Do not set the date between 9:00 p.m. and 1:00 a.m., as the date may not change Battery life : Approx. 2 years properly. If it is necessary to set the date during that period of time, first change the Years Battery : SEIKO SR920SW time to any time outside of this period, set the date, and then reset to the correct time. Do not press any button when the crown is at the second click position, as this will l If the stopwatch is used for more than 2 hours a day, the battery life may be less move the STOPWATCH hands. - Page 6 Necessary procedure after battery change l We recommend that you contact an AUTHORIZED PULSAR DEALER for battery replacement. After the battery is replaced with a new one, or in case any of the hands should STOPWATCH move improperly, follow the procedure below to reset the hands to “0”...
- Page 7 10 bar/15 bar/20 bar and is suitable for taking withstand up to 3 bar, such as acci- a bath, shallow diving, but not for scuba diving. dental contact with splashes of water or rain, but it We recommend that you wear a PULSAR Diver’s is not designed for swimming or diving. watch for scuba diving.
- Page 8 * Before using the water resistance 5, 10, 15 or 20 bar watch in water, be sure the CARE OF CASE AND BRACELET MAGNETISM crown is pushed in completely. Your watch will be ad- To prevent possible rusting of Do not operate the crown when the watch is wet or in water. If used in sea water, versely affected by strong rinse the watch in fresh water and dry it completely. the case and bracelet caused magnetism. Keep it away * When taking a shower with the water resistance 5 bar watch, or taking a bath with by dust, moisture and perspi- from close contact with ration, wipe them periodically the water resistance 10, 15 or 20 bar watch, be sure to observe the following: magnetic objects. • Do not operate the crown when the watch is wet with soapy water or shampoo. with a soft dry cloth. • If the watch is left in warm water, a slight time loss or gain may be caused. This PERIODIC CHECK SHOCKS &...
Need help?
Do you have a question about the VD50 and is the answer not in the manual?
Questions and answers