Table of Contents
Advertisement
Quick Links
13-08-043 93-32D0.indd 1
Owner's Manual
HDMI Over Cat5
1x2 Extenders
Models: B126-2A1, B126-2A0
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2013 Tripp Lite. All rights reserved.
2
2
4
5
7
10
13
17
19
8/28/2013 2:17:35 PM
Advertisement
Table of Contents
Related Manuals for Tripp Lite B126-2A1
Summary of Contents for Tripp Lite B126-2A1
-
Page 1: Table Of Contents
1 x 2 Extender Kit with Remote/Repeater Installation Standard Extender/Splitter Installation Extender/Splitter with Remote/Repeater Installation Troubleshooting Warranty & Warranty Registration 1111 W. 35th Street, Chicago, IL 60609 USA www.tripplite.com/support Copyright © 2013 Tripp Lite. All rights reserved. 13-08-043 93-32D0.indd 1 8/28/2013 2:17:35 PM... -
Page 2: Package Contents
Package Contents • B126-2A1 Kit or B126-2A0 Receiver Unit • External Power Supply (Input: 100-240V, 50/60Hz, 0.5A Output: 5V, 2A) • Mounting Hardware • Screwdriver for Equalization Adjustment • Owner’s Manual Product Features • Extends an HDMI signal to 2 monitors up to 200 ft. from the source over a single Cat5e/6 cable. • A B126-002 or B126-004 extender/splitter transmitter unit is required for use with the B126-1A0 1x2 receiver unit. • Extends a 1080p (60Hz) signal up to 150 ft. from the source using Cat6 cabling, or up to 125 ft. using Cat5 cabling. -
Page 3: Optional Accessories
Product Features • Supports both stereo and 7.1-channel surround sound audio (7.1-channel surround sound signal will be Multi-Channel or PCM). • HDCP and 3D compatible. • Plug and play; No software or drivers required. • Compatible with all operating systems. • Mounting hardware included. Optional Accessories: • B126-110 – Remote Repeater Unit • N202-Series Cat6 24 AWG, Solid Wire Patch Cables • P568-Series High-Speed HDMI Cables 13-08-043 93-32D0.indd 3 8/28/2013 2:17:35 PM... -
Page 4: Mounting Instructions
Note: The images below show a B126-1A1 HDMI over Cat5 Receiver Unit, but the mounting hardware installation is the same for the B126-2A1 and B126-2A0. Wall-mount 1 Wall-mount 2 19”... -
Page 5: Standard 1 X 2 Extender Kit Installation
Cat6 cabling. When using Cat5 cabling, the maximum extension distance is 175 ft. at 1080i (60Hz), and 125 ft. at 1080p (60Hz). 4. The B126-2A1 is set to transmit a stereo audio signal by default. Press the Audio button on the transmitter unit to switch to 7.1-channel surround sound audio. - Page 6 Standard 1 x 2 Extender Kit Installation Make sure all devices being connected are powered OFF. Connect the HDMI source to the INPUT port on the transmitter unit using a Tripp Lite P568-Series High-Speed HDMI Cable. Optional: Connect a monitor to the LOCAL port on the transmitter unit using a Tripp Lite P568-Series High-Speed HDMI Cable. Connect the external power supply to the transmitter unit and plug the transmitter unit into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU), or Uninterruptible Power Supply (UPS). The green RJ45 LED illuminates to indicate that the unit is receiving power from the external power supply. Using Cat5e/6 cable, connect the RJ45 port on the transmitter unit marked OUTPUT to the RJ45 port on the receiver unit marked INPUT. Connect the external power supply to the receiver unit and plug the receiver unit into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU), or Uninterruptible Power Supply (UPS). The green RJ45 LED illuminates to indicate that the unit is receiving power from the external...
-
Page 7: X 2 Extender Kit With Remote/Repeater Installation
Tripp Lite’s N202-Series, is required to achieve maximum distance and resolution. 3. The B126-2A1 is set to transmit a stereo audio signal by default. Press the Audio button on the transmitter unit to switch to 7.1-channel surround sound audio. (7.1-channel surround sound signal will be Multi-Channel or PCM) Up to 175 ft. - Page 8 Tripp Lite Surge Suppressor, Power Distribution Unit (PDU), or Uninterruptible Power Supply (UPS). The green power and the green RJ45 LEDs will illuminate to indicate that the unit is receiving power from the external power supply. Up to 4 units can be daisy-chained (3 repeaters and 1 active receiver). To add additional repeater units, proceed to step 8. To finish your installation with the B126-2A1 receiver unit, proceed to step 11. Using Cat5e/6 cable, connect the RJ45 port on the repeater unit marked OUTPUT to the RJ45 port on a second repeater unit marked INPUT. Connect a monitor to the HDMI OUTPUT port on the repeater unit using a Tripp Lite P568-Series High-Speed HDMI Cable. Connect the external power supply to the repeater unit and plug the repeater unit into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU), or Uninterruptible Power Supply (UPS). The green power...
- Page 9 1 x 2 Extender Kit with Remote/Repeater Installation To add a third remote/repeater unit, repeat steps 8 through 10. To finish your installation with the B126-2A1 receiver unit, proceed to step 11. Using Cat5e/6 cable, connect the RJ45 port on the repeater unit marked OUTPUT to the RJ45 port on the receiver unit marked INPUT. Connect a monitor to the OUTPUT 1 port on the receiver unit using a Tripp Lite P568-Series High-Speed HDMI cable. Repeat step 12 for the OUTPUT 2 port on the receiver unit.
-
Page 10: Standard Extender/Splitter Installation
1. Test to make sure that the entire installation works properly before running cables through ceilings/walls. 2. 24 AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, is required to achieve maximum distance and resolution. 3. The diagram below shows the maximum extension distance when using Cat6 cabling. - Page 11 Standard Extender/Splitter Installation Up to 200 ft. at 1080i @ 60Hz (Cat6) Up to 150 ft. at 1080p @ 60Hz (Cat6) B126-2A0 B126-2A0 B126-2A0 B126-2A0 B126-004 BLU-RAY OPTIONAL LOCAL MONITOR Make sure all devices being connected are powered OFF. Connect the HDMI source to the INPUT port on a B126-002 or B126-004 transmitter unit using a Tripp Lite P568-Series High-Speed HDMI Cable.
- Page 12 Standard Extender/Splitter Installation Connect the external power supply to the receiver unit and plug the receiver unit into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU), or Uninterruptible Power Supply (UPS). The green RJ45 LED illuminates to indicate that the unit is receiving power from the external power supply. Connect a monitor to the OUTPUT 1 port on the receiver unit using a Tripp Lite P568-Series High-Speed HDMI Cable.
-
Page 13: Extender/Splitter With Remote/Repeater Installation
5. Although the installation instructions below mention the B126-2A0 1x2 receiver unit only, Tripp Lite offers two additional active receivers that can be used in the event that only one monitor is needed at the end of a repeater chain: B126-1A0 and B126-1A0-WP-1. - Page 14 Extender/Splitter with Remote/Repeater Installation Up to 175 ft. at 1080i (60Hz) Up to 175 ft. at 1080i (60Hz) Up to 125 ft. at 1080p (60Hz) Up to 125 ft. at 1080p (60Hz) B126-110 REMOTE/ B126-110 REMOTE/ B126-110 REMOTE/ B126-2A0 REPEATER REPEATER REPEATER REMOTE RECEIVER...
- Page 15 Extender/Splitter with Remote/Repeater Installation Using Cat5e/6 cable, connect a RJ45 OUTPUT port on the transmitter unit to the RJ45 INPUT port on the B126-110 repeater unit. Connect a monitor to the HDMI OUTPUT port on the repeater unit using a Tripp Lite P568-Series High-Speed HDMI Cable. Connect the external power supply to the remote/repeater unit and plug the remote/repeater unit into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU), or Uninterruptible Power Supply (UPS). The green power and RJ45 LEDs will illuminate to indicate that the unit is receiving power from the external power supply. Up to 4 units can be daisy-chained (3 repeaters and 1 active receiver). To add additional repeater units, proceed to step 8. To finish your installation with a B126-2A0 1x2 receiver unit, proceed to step 11. Using Cat5e/6 cable, connect the RJ45 port on the repeater unit marked OUTPUT to the RJ45 port on a second repeater unit marked INPUT.
- Page 16 Extender/Splitter with Remote/Repeater Installation Using Cat5e/6 cable, connect the RJ45 port on the repeater unit marked OUTPUT to the RJ45 port on the B126-2A0 receiver unit marked INPUT. Connect a monitor to the OUTPUT 1 port on the receiver unit using a Tripp Lite P568-Series High-Speed HDMI Cable.
-
Page 17: Troubleshooting
Troubleshooting If you are unable to get an acceptable image after following the installation instructions, try these troubleshooting tips: Are the external power supplies that came with the product connected and plugged into a working power source? For the product to function properly, it must be connected to and receiving power from the external power supply. Was the power to the connected devices turned off prior to installation? If not, restart them. - Page 18 Troubleshooting What type of cabling are you using? Inferior cabling can result in poor performance, so it is important that you use cables that support the video resolution you are trying to obtain. To achieve maximum distance and resolution, 24 AWG solid wire UTP cable must be used. Tripp Lite’s N202- Series Cat6 Cables are made with 24 AWG solid wire, as are the N022- 01K-GY (Cat5) and N222-01K-GY Bulk Cables. Also, the HDMI cables you are using must support the resolution you are trying to obtain. Inexpensive, low quality HDMI cables may not support the maximum resolution. It is recommended that you use Tripp Lite’s P568-Series High-Speed HDMI Cables that are pre-tested to work with all B126-Series extender products.
-
Page 19: Warranty & Warranty Registration
Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!* * No purchase necessary. Void where prohibited. Some restrictions apply. See website for details. WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union) Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to: • Send old equipment for recycling on a one-for-one, like-for-like basis (this varies... - Page 20 FCC Notice, Class B This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no...