Page 1 Portégé User’s Manual M100 ORTÉGÉ M100 PORTÉGÉ M100 PORTÉGÉ M100 Choose freedom. Choose freedom. Choose freedom. computers.toshiba-europe.com...
Page 2 Photo CD is a trademark of Eastman Kodak. Centronics is a registered trademark of Centronics Data Computer Corporation. Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under licence. i.LINK is a trademark of Sony Corporation. Other trademarks and registered trademarks not listed above may be used in this manual.
Page 3 User's Manual Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Page 4: Wireless Interoperability
User's Manual Information to Wireless LAN Users Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any Wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant ■...
Page 5: Regulatory Information
User's Manual Regulatory Information The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.
Page 6 User's Manual Belgium/ België/ For outdoor usage only channel 10 (2457 MHz) Belgique and 11 (2462 MHz) is allowed. For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m.
Page 7 TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this TOSHIBA Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA .
Page 8 User's Manual Caution: Exposure to Radio Frequency Radiation. The radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimised.
Page 9 2. In case that RF interference occurs to Other Radio Stations from this equipment, please change promptly the frequency for use, place to use, or stop emitting Radio. 3. Please contact TOSHIBA Direct PC if you have a problem, such as interference from this equipment to Other Radio Stations.
Page 10 In other countries, the drive is certified to comply with the requirement pursuant to IEC 825 and EN60825 on class 1 laser product. This computer is equipped with the optical drive in the following list according to the model. Manufacturer Type TOSHIBA SD-C2612 TEAC DW-224E Portégé M100...
Page 11: General Precautions
User's Manual General Precautions TOSHIBA computers are designed to optimise safety, minimise strain and withstand the rigours of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 12 Read additional restrictions under “Environmental Conditions” in your product Resource Guide. Contact TOSHIBA Service and Support for more information. Pressure or impact damage Do not apply heavy pressure to the computer or subject it to strong impact.
Page 13: Working Environment
This product was designed to fulfil the EMC (electromagnetic compatibility) requirements to be observed for so-called "Residential, commercial and light industry environments". TOSHIBA do not approve the use of this product in working environments other than the above mentioned "Residential, commercial and light industry environments".
Page 14 User's Manual Network connection (class A warning) If this product has networking capabilities and will be connected to a network, Class A radiation limits will be observed (in accordance with technical conventions). This means that if the product will be used in a domestic environment, other devices in the near surrounding may suffer interference.
Page 15: Table Of Contents
Table of Contents Portégé M100 Table of Contents Preface ..................xxii Manual contents................... xxii Conventions..................xxiii Abbreviations..................xxiii Icons ....................xxiii Keys....................xxiii Key operation ...................xxiv Display ....................xxiv Messages ..................xxiv Chapter 1 Introduction..............1-1 Equipment checklist ................1-1 Features ....................1-3 Special features..................1-9 Utilities ....................1-11 Options....................1-13 Chapter 2 The Grand Tour............2-1 Front with the display closed ...............2-1...
Page 16 Shut Down mode (Boot mode) ............3-9 Hibernation mode ................3-10 Standby mode .................3-12 Restarting the computer..............3-13 Restoring the preinstalled software ..........3-14 Restoring the complete system ............3-14 Restoring TOSHIBA utilities and drivers ..........3-14 Chapter 4 Operating Basics .............4-1 Using AccuPoint II.................4-1 AccuPoint II precautions..............4-2 Replacing the cap................4-3 Changing Slim SelectBay modules............4-3...
Page 17 Table of Contents Wireless LAN ..................4-16 Limitation of Liability................4-16 Usage Restrictions ................4-16 Wireless LAN ...................4-19 Security....................4-19 Wireless communication switch ............4-19 Wireless communication Indicator ..........4-20 LAN .......................4-20 LAN cable types ................4-20 Connecting the LAN cable...............4-21 Disconnecting the LAN cable ............4-21 Using the microphone.................4-22 Using the internal modem ..............4-22 Region selection ................4-23 Properties menu ................4-23...
Page 18 Retaining data with power off............6-11 Extending battery life...............6-12 Replacing the battery pack ..............6-13 Removing the battery pack .............6-13 Installing the battery pack ...............6-14 TOSHIBA Password Utility..............6-15 User password ................6-15 Supervisor password...............6-16 Starting the computer by password ..........6-17 Power-up modes .................6-17 Windows utilities................6-17...
Page 19 Table of Contents Chapter 8 Optional Devices .............8-1 PC cards....................8-2 Installing a PC card ................8-2 Removing a PC card................8-3 SD cards....................8-3 Formatting an SD card ..............8-4 Installing an SD card................8-4 Removing an SD card................8-5 SD card care..................8-6 Memory expansion................8-6 Installing memory module..............8-7 Removing memory module..............8-9 Additional battery pack...............8-10 Slim SelectBay 2nd battery pack ............8-10...
Page 20 Table of Contents Chapter 9 Troubleshooting ............9-1 Problem solving process ..............9-1 Preliminary checklist................9-2 Analysing the problem ...............9-2 Hardware and system checklist............9-3 System start-up .................9-4 Self test....................9-4 Power ....................9-5 Password...................9-7 Keyboard ...................9-7 LCD panel..................9-8 Hard disk drive ..................9-8 DVD-ROM drive .................9-9 CD-RW/DVD-ROM drive ..............9-10 Diskette drive...................9-12 Infrared port..................9-12...
Page 21 Table of Contents Appendix A Specifications ............A-1 Appendix B AC Power Cord and Connectors ....... B-1 Appendix C The TOSHIBA International Warranty ....C-1 Appendix D Keyboard Layouts ..........D-1 Appendix E Display Controller and Modes......E-1 Appendix F If your computer is stolen ........
Page 22: Preface
Preface Portégé M100 Preface Congratulations on your purchase of the TOSHIBA Portégé M100 computer. This powerful, light-weight notebook computer is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Portégé M100 computer.
Page 23: Conventions
Preface Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hotkeys. Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes and how to set a password. Chapter 7, HW Setup, explains how to configure the computer using the HW Setup program.
Page 24: Key Operation
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
Page 25: Chapter 1 Introduction
This chapter provides an equipment checklist, and it identifies the computer’s features, utilities and options. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Hardware Carefully unpack your computer.
Page 26 LAN Driver ■ Wireless LAN Driver ■ Infrared Device Driver ■ Microsoft Internet Explorer 6.0 ■ DVD Video Player ■ TOSHIBA Power Saver ■ TOSHIBA Console ■ TOSHIBA Controls ■ Online manual ■ Documentation: ■ Portégé M100 Portable Personal Computer User’s Manual ■...
Page 27: Features
Introduction Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor ® Built-in The computer is equipped with an Intel ®...
Page 28 Introduction Disks Built-in Hard disk ■ 40 billion bytes (37.26 GB) Other hard disks may be introduced in the future. DVD-ROM drive Your computer is equipped with a full-size, DVD-ROM drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor.
Page 29 Introduction Display The computer’s LCD panel supports high-resolution video graphics. The screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in 12.1" XGA-TFT, 1024 horizontal × 768 vertical pixels, up to 16 M colours Graphics controller Graphics controller maximizes display performance.
Page 30 Introduction Ports Headphone Enables connection of a stereo headphone Microphone Enables connection of a monaural microphone Infrared The serial infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.152 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or 9.6 kbps data transfer with IrDA 1.1 compatible external devices.
Page 31 Introduction Communications Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in some markets.
Page 32: Slim Selectbay
Slim SelectBay is a single-drive bay that accommodates a DVD-ROM drive, CD-RW/DVD-ROM drive, secondary hard disk drive or secondary battery. The TOSHIBA Mobile Extension enables hot insertion of modules when you are using a plug and play operating system. Security...
Page 33: Special Features
Introduction Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. TOSHIBA Console Press this button to launch an application button automatically. The default is TOSHIBA Console.
Page 34 Use the Fan item of the Power Save Modes window in TOSHIBA Power Saver. Maximum Turns on fan first, then if...
Page 35: Utilities
To start the utility, open the Control Panel, click Printers and Other Hardware and click the TOSHIBA HW Setup icon. TOSHIBA Password The TOSHIBA Password Utility provides two...
Page 36 To activate this utility, select TOSHIBA Mobile Extension from TOSHIBA Console. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication device and network connections. TOSHIBA ConfigFree also allows you to find communication problems and create profiles for easy switching between location and communication networks.
Page 37: Options
Battery Pack An addition Battery Pack can be purchased from your TOSHIBA dealer. The Battery Pack is identical to the one that came with your computer. Use it as a spare or replacement. Universal AC Adaptor If you use your computer at more than one site,...
Page 38: Slim Selectbay Options
Introduction Slim SelectBay options The following modules can be installed in the Slim SelectBay. All other modules are options. CD-RW/DVD-ROM Refer to the Features section for details. Slim SelectBay HDD An adaptor lets you install an optional HDD adaptor described in Chapter 8, Optional Devices. Hard disk drive You can increase your computer’s data storage capacity with an additional 40 billion bytes...
Page 39: Chapter 2 The Grand Tour
The Grand Tour Portégé M100 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed The figure below shows the computer’s front with its display panel in the closed position.
Page 40: Left Side
The Grand Tour Left side The figure below shows the computer’s left side. SECURITY LOCK SLOT DC IN 15V MICROPHONE JACK HEADPHONE JACK FAN VENT PC CARD SLOT INFRARED PORT VOLUME CONTROL The left side of the computer Security lock slot A security cable attaches to this slot.
Page 41 The Grand Tour PC card slot A PC card slot can accommodate two 5 mm PC cards (Type II) or one 10.5 mm PC card (Type III). The slot supports 16-bit PC cards and CardBus PC cards. Keep foreign objects out of the PC card slot. A pin or similar object can damage the computer’s circuitry.
Page 42: Right Side
The Grand Tour Right side The figure below shows the computer’s right side. BATTERY LOCK/BATTERY RELEASE LATCH SD CARD INDICATOR SD CARD SLOT SLIM SELECTBAY The right side of the computer Battery lock/Battery A sliding lock (vertical sliding) prevents release latch inadvertent release of the battery pack.
Page 43: Back Side
The Grand Tour Back side The figure below shows the computer’s back side. LAN ACTIVE LINK INDICATOR INDICATOR (ORANGE) (GREEN) I.LINK PORT FAN VENT LAN JACK MODEM JACK EXTERNAL MONITOR USB PORTS PORT The computer’s back side LAN jack This jack lets you connect to a LAN. The adaptor Ether has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast...
Page 44: Underside
The Grand Tour Universal Serial Bus Two Universal Serial Bus ports comply with the (USB 2.0) ports USB 2.0 standard, which enables data transfer speeds 40 times faster than the USB 1.1 standard. (The ports also support USB 1.1.) Keep foreign objects out of the USB connectors. A pin or similar object can damage the computer’s circuitry.
Page 45 Chapter 6, Power and Power-Up Modes, describes how to access the battery pack. Additional battery packs can be purchased from your TOSHIBA dealer to extend the computer’s battery operating time. HDD pack cover Two screws secures the HDD cover.
Page 46: Front With The Display Open
The figure below shows the front of the computer with the display open. To open the display, slide the display latch on the front of the computer and lift the display up. Position the display at a comfortable viewing angle. TOSHIBA TOSHIBA STEREO DISPLAY...
Page 47 LCD and CRT. You can also return to single display by pressing this button twice. The setting of TOSHIBA Presentation button can be changed through the property of TOSHIBA Controls. Display mode is changed to the multi-monitor display by selecting "Different Image"...
Page 48 If the computer is off, pressing this button starts the computer and launches the associated program automatically. The default is TOSHIBA Console. A pointer control device located in the centre of AccuPoint II the keyboard is used to control the on-screen pointer.
Page 49: Indicators
The Grand Tour Indicators The figure below shows the indicators, which light when various computer operations are in progress. WIRELESS MAIN BATTERY DISK SLIM SELECTBAY COMMUNICATION DC IN 15V POWER The power source/system indicators Power source/system indicators DC IN 15V The DC IN 15V indicator glows green when DC power is supplied from the AC power adaptor.
Page 50 The Grand Tour Slim SelectBay The Slim SelectBay indicator glows green when the computer is accessing a DVD-ROM drive, CD-RW/DVD-ROM drive, or Slim SelectBay HDD adaptor in the Slim SelectBay. When the secondary battery is in the Slim SelectBay, the Slim SelectBay indicator glows as follows: Orange: Indicates the AC adaptor is connected and charging the battery.
Page 51: Ac Adaptor
Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. Use only the AC adaptor supplied as an accessory. Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fine or rupture.
Page 52: Slim Selectbay Modules
The Grand Tour Slim SelectBay modules The Slim SelectBay can accommodate the following modules: DVD-ROM drive, optional CD-RW/DVD-ROM drive, optional secondary battery pack and optional Slim SelectBay HDD adaptor. DVD-ROM drive A full-size DVD-ROM drive module lets you run either 12 cm (4.72") or 8 cm (3.15") digital video disc/compact disc without using an adaptor.
Page 53 The Grand Tour Eject button Press the eject button to open the drawer partially. Eject hole Insert a slender object to open the drawer when the power to the computer is off. CD/DVD-In-Use This indicator lights when the CD/DVD is being Indicator accessed.
Page 54: Cd-Rw/Dvd-Rom Drive (Optional)
The Grand Tour CD-RW/DVD-ROM drive (optional) A full-size CD-RW/DVD-ROM drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The computer is configured with either a DVD-ROM drive or CD-RW/DVD-ROM drive.
Page 55 The Grand Tour CD/DVD-In-Use This indicator lights when the CD/DVD is being Indicator accessed. Eject hole Insert a slender object to open the drawer when the power to the computer is off. Eject button Press the eject button to open the drawer partially.
Page 56: Secondary Battery Pack
The Grand Tour Secondary battery pack An optional battery pack can be installed in the Slim SelectBay to increase the computer’s battery power and operating time. For details, refer to the documentation accompanying the secondary battery pack. Refer to Chapter 8, Optional Devices, for details on installing a secondary battery pack.
Page 57: Chapter 3 Getting Started
Getting Started Portégé M100 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space — for your health and safety Be sure also to read the Safety Instruction Manual. This guide, which is included with the computer, explains product liability.
Page 58: General Conditions
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Make sure there is adequate space around the computer for proper ventilation.
Page 59: Seating And Posture
Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to the illustration below. Posture and positioning of the computer ■...
Page 60: Lighting
Getting Started Lighting Proper lighting can improve legibility of the display and reduce eye strain. ■ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare. ■...
Page 61: Opening The Display
Getting Started Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right to unlatch the display panel. 2. Lift the panel up and adjust it to the best viewing angle for you. When you open the display, hold it with both hands and lift up slowly.
Page 62: Connecting The Ac Adaptor
Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible. Use of any incompatible adaptor could dam age your computer. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor.
Page 63 Getting Started 1. Connect the power cord to the AC adaptor. Connecting the power cord to the AC adaptor 2. Connect the AC adaptor’s DC output plug to the DC IN 15V port on the left side of the computer. Connecting the adaptor to the computer 3.
Page 64: Turning On The Power
Getting Started Turning on the power This section describes how to turn on the power. After you turn on the power for the first time, do not turn it off until you have set up the operating system. 1. If an external diskette drive is connected, make sure it is empty. If a diskette is in the drive, press the eject button and remove the diskette.
Page 65: Turning Off The Power
Getting Started Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen.
Page 66: Hibernation Mode
For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.
Page 67 First, however, make the appropriate settings according to the steps below. 1. Open the Control Panel. 2. Open Performance and Maintenance and open TOSHIBA Power Saver. 3. Select the Hibernate window, select the Enable Hibernate support check box and click the Apply button.
Page 68: Standby Mode
When the AC adaptor is used, the computer goes into Standby mode depending on the setting of the TOSHIBA Power Saver feature. To restore operation, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup.
Page 69: Restarting The Computer
1. Click Start, click Turn Off Computer and click Stand by. 2. Close the display panel. This feature must be enabled. Refer to the System Power Mode item in TOSHIBA Power Saver described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.
Page 70: Restoring The Preinstalled Software
1. Load the Product Recovery CD-ROM in the optical media drive and turn off the computer’s power. 2. Hold down the F12 key and turn on the power. When the TOSHIBA logo appears, release the F12 key. 3. Use the left or right cursor key to select the CD-ROM icon in the displayed menu.
Page 71: Chapter 4 Operating Basics
Operating Basics Portégé M100 Chapter 4 Operating Basics This chapter gives information on basic operations including using the AccuPoint II, changing Slim SelectBay modules, optical media drives, the optional external diskette drive, Wireless LAN, the LAN, the microphone and the internal modem. It also provides tips on caring for your computer and heat dispersal.
Page 72: Accupoint Ii Precautions
Operating Basics Two large buttons below the keyboard are used like the buttons on a mouse pointer. Press a button to select a menu item or to manipulate text or graphics designated by the pointer. Press the left small button can scroll up the screen.
Page 73: Replacing The Cap
Operating Basics Replacing the cap The AccuPoint II cap is an expendable item that should be replaced after prolonged use. There is a spare AccuPoint II cap supplied with the computer. 1. To remove the AccuPoint II cap, firmly grasp the cap and pull it straight up.
Page 74: Removing A Module
Operating Basics The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1, Introduction for information on using this utility to change modules while the computer’s power is on. Removing a module Remove the DVD-ROM drive as described below.
Page 75: Installing A Module
Operating Basics Installing a module Install the Slim SelectBay HDD adaptor as described below. ■ Insert the Slim SelectBay HDD adaptor in the computer as shown below and press until the ejector clicks. Installing the Slim SelectBay HDD adaptor Using optical media drives The text and illustrations in this section refer primarily to the DVD-ROM drive.
Page 76: Loading Discs
Operating Basics Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-5 to 4-9. 1. a. When the power is on, press the DVD-ROM eject button to open the drawer slightly. Pressing the DVD-ROM eject button b.
Page 77 Operating Basics 2. Pinch the drawer gently and pull until it is fully opened. Pulling the drawer open 3. Lay the CD/DVD, label side up, in the drawer. When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray.
Page 78 Operating Basics 4. Press gently at the centre of the CD/DVD until you feel it click into place. The CD/DVD should lie below the top of the spindle, flush with the spindle base. Inserting a CD/DVD 5. Push the centre of the drawer to close it. Press gently until it locks into place.
Page 79: Removing Discs
Operating Basics Removing discs To remove the CD/DVD, follow the steps below and refer to the following figure. Do not press the eject button while the computer is accessing the DVD-ROM drive. Wait for the Slim SelectBay indicator to go out before you open the drawer.
Page 80: Writing Cds On Cd-Rw/Dvd-Rom Drive
High-Speed CD-RW: RICOH Co., Ltd. Ultra-Speed CD-RW: MITSUBISHI CHEMICAL CORPORATION TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ CD-RW can generally be rewritten about 1,000 times. However, the actual number of rewrites is affected by the quality of the media and the way it is used.
Page 81: When Writing Or Rewriting
Operating Basics ■ Write from the computer's HDD to the CD. Do not try to write from shared devices such as a LAN server or any other network device. ■ Writing with software other than Drag'n Drop CD+DVD has not been confirmed.
Page 82: Media Care
Operating Basics Media care This section provides tips on protecting data stored on your CD/DVDs and diskettes. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs Handle your media with care.
Page 83: Using The Usb Diskette Drive (Optional)
Operating Basics Using the USB diskette drive (optional) A 3 ½" diskette drive connects to the computer’s USB port. It accommodates 1.44-megabyte or 720-kilobyte diskettes. USB CONNECTOR DISK-IN-USE DISKETTE SLOT EJECT BUTTON INDICATOR The USB diskette drive Eject button When a diskette is fully seated in the drive, the eject button pops out.
Page 84: Connecting The Usb Diskette Drive
Operating Basics Connecting the USB diskette drive To connect the drive, plug the diskette drive connector into a USB port. Refer to the following figure. Make sure the connector is right side up and properly aligned with the socket. Do not try to force the connection, doing so can damage the connecting pins.
Page 85: Disconnecting The Usb Diskette Drive
Operating Basics Disconnecting the USB diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive.
Page 86: Wireless Lan
Operating Basics Wireless LAN Limitation of Liability For damage occurring due to an earthquake or thunder, fire beyond our responsibility, action by third party, other accident, intentional or accidental mistakes by a user, misuse, use under abnormal conditions, we do not take any responsibility. For incidental damage (loss of business profit, business interruption, etc.) occurring due to use or disability of the product, we do not take any responsibility.
Page 87 Operating Basics Turn OFF the Wireless Communication switch of Wireless Products in a congested place, such as a crowded commuter train. Radio waves can potentially affect cardiac pacemaker operation, thereby causing respiratory troubles. Keep this product away from a cardiac pacemaker at least 22cm. Radio waves can potentially affect cardiac pacemaker operation, thereby causing respiratory troubles.
Page 88 Wireless LAN Mini PCI-Card. Do not use this equipment in Countries/Regions, in which this equipment is not approved. Contact one of your TOSHIBA Worldwide Computer Representatives in Appendix C for further information. Australia * Austria *...
Page 89: Wireless Lan
LAN to cause illegal intrusion, eavesdropping, and loss or destruction of stored data. TOSHIBA strongly recommend the customer to enable the WEP function. 2. TOSHIBA is not liable for the eavesdropping of data due to the use of wireless LAN and the damage thereof. Wireless communication switch You can enable or disable wireless LAN functions with the on/off switch.
Page 90: Wireless Communication Indicator
Operating Basics Wireless communication Indicator The Wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Indicator glows Wireless communication switch is on. Wireless LAN is turned on by an application.
Page 91: Connecting The Lan Cable
Operating Basics Connecting the LAN cable To connect the LAN cable, follow the steps below. Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up. Do not connect any other cable to the LAN's jack except the LAN cable.
Page 92: Using The Microphone
Operating Basics Using the microphone Your computer has a built-in microphone that can be used to record monaural sounds into your applications. It can also be used to issue voice commands to applications that support such functions. Since your computer has a built-in microphone and speakers, “howling” may be heard under certain conditions.
Page 93: Region Selection
1. Click start, point to All Programs, point to TOSHIBA Internal Modem and click Region Select Utility. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Page 94 Operating Basics Open the Dialling Properties dialog box after selecting region. The dialling properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony. Open dialog box, if the modem and Telephony Current Location region code do not match.
Page 95: Connecting
Operating Basics Connecting To connect the internal modem cable, follow the steps below. The modular cable that comes with the computer must be used to connect a modem. Connect the end of the modular cable with the core to the computer. In case of a lightning storm, unplug the modem cable from the telephone jack.
Page 96: Cleaning The Computer
Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.
Page 97: Heat Dispersal
CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Power Save Mode window in TOSHIBA Power Saver. Maximum Turns on the fan first, then if necessary, lowers the CPU processing speed.
Page 98: Chapter 5 The Keyboard
The Keyboard Portégé M100 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.
Page 99: F1 ... F12 Function Keys
The Keyboard F1 … F12 function keys The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed.
Page 100: Soft Keys: Fn Key Combinations
The Keyboard Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features. Some software may disable or interfere with soft-key operations. Soft-key settings are not restored by the Standby feature.
Page 101: Hotkeys
The Keyboard Press Fn + Enter to simulate Enter on the enhanced keyboard’s numeric keypad. Press Fn + Ctrl to simulate the enhanced keyboard’s right Ctrl key. Hotkeys Hotkeys (Fn + a function or Esc key) let you enable or disable certain features of the computers.
Page 102 Continue holding down Fn and press F2 again to change the setting. You can also change this setting through the Plugged in or Running on batteries item of the TOSHIBA Power Saver Properties window in TOSHIBA Power Saver. Standby: When you press Fn + F3, the computer can enter Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification.
Page 103: Fn Sticky Key
If no wireless communication device is installed, no dialog box will appear. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and they press an “F number”...
Page 104: Windows Special Keys
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: one activates the Start menu and the other has the same function as the secondary mouse button. This key activates the Windows Start menu. This key has the same function as the secondary mouse button.
Page 105: Numeric Mode
The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in the following figure. Press Fn + F11 again to turn off the overlay. The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard...
Page 106: Temporarily Using Overlay (Overlay Off)
The Keyboard Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay.
Page 107: Chapter 6 Power And Power-Up Modes
Power and Power-Up Modes Portégé M100 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Page 108 *2 When the main battery is not charging *3 For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. If a main battery and a secondary battery are installed, the computer does not shut down until the charge in both batteries is exhausted.
Page 109: Power Indicators
Power and Power-Up Modes Power indicators As shown in the above table, the Battery, Slim SelectBay, DC IN 15V and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the main battery and the Slim SelectBay indicator to determine the status of the secondary battery.
Page 110: Power Indicator
Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power it will be lost. When...
Page 111: Secondary Battery (Option)
Press [F1] key to set Date/Time. The computer’s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of.
Page 112: Care And Use Of The Battery Pack
Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance.
Page 113 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture. 3. Make sure the battery is securely installed in the computer before attempting to charge the battery pack.
Page 114 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling centre to save resources and prevent environmental damage. Cover the terminals with electrical tape to prevent short-circuits, which could cause the battery pack to ignite or rupture.
Page 115: Charging The Batteries
The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Do not attempt to charge the battery pack with any other charger.
Page 116: Monitoring Battery Capacity
In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.
Page 117: Maximising Battery Operating Time
Power and Power-Up Modes Maximising battery operating time A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ■ How you configure the computer, for example, whether you enable battery-power saving options.
Page 118: Extending Battery Life
Power and Power-Up Modes Extending battery life To maximise the life of your battery pack: ■ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below.
Page 119: Replacing The Battery Pack
6. Pull the battery pack forward to remove it. For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Removing the battery pack Portégé M100 6-13...
Page 120: Installing The Battery Pack
Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. Be sure the computer’s power is off and all cables are disconnected. 2. Insert the battery pack.
Page 121: Toshiba Password Utility
Power and Power-Up Modes TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password. User password To start the utility, point to or click the following items: Start -> All Programs ->...
Page 122: Supervisor Password
If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items: Start ->...
Page 123: Starting The Computer By Password
Refer also to the sections Turning on the power and Turning off the power in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation.
Page 124: Panel Power Off
Power and Power-Up Modes Panel power off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power turns on in Standby or Hibernation mode but not in boot mode. If the panel power off function is enabled and you use Shut down Windows, do not close the display until the shut down function is completed.
Page 125: Chapter 7 Hw Setup
HW Setup Portégé M100 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. HW Setup TOSHIBA HW Setup lets you configure settings for pointing devices, display, CPU, boot priority, keyboard, USB, LAN, general, device config and parallel/printer.
Page 126 HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. Device Config Device Configuration This option lets you set the device configuration.
Page 127 HW Setup Pointing Devices Pointing Devices This tab lets you select Auto-Selected and Simultaneous. Auto-Selected If a PS/2 mouse is connected to the optional Advanced Port Replicator II when you turn on the power, the PS/2 mouse is enabled and the AccuPoint II is disabled.
Page 128: Boot Priority
PC card HDD boot is supported only by slot 0 on the computer. Support is guaranteed only for TOSHIBA PC card HDDs. When you assign a PC card HDD top priority, "PC" is not displayed. However, the PC card HDD takes the position of HDD in the Boot Priority Options list above.
Page 129 HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, Select Bay HDD, CD-ROM, FDD, Network (LAN), PC (ATA) card boot.
Page 130 HW Setup HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. Built-in HDD ->...
Page 131 HW Setup Keyboard External Keyboard Fn key Use this option to set a key combination on an external keyboard to emulate the Fn key on the computer’s internal keyboard. Setting an Fn key equivalent will let you use “Hotkeys” by pressing the set combination instead of the Fn key.
Page 132 HW Setup USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled.
Page 133: Chapter 8 Optional Devices
Optional Devices Portégé M100 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. The following optional devices are available from your TOSHIBA dealer: Cards/memory ■ PC cards ■ SD cards ■ Memory expansion Power devices ■...
Page 134: Pc Cards
The computer is equipped with a PC card expansion slot that can accommodate two 5 mm Type II cards or one 10.5 mm Type III card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
Page 135: Removing A Pc Card
Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. In Windows XP, open the Safely Remove Hardware icon on the system tray and disable the PC card. 2. Press the eject button of the PC card you want to remove to extend the button.
Page 136: Formatting An Sd Card
SD memory cards are sold with format in conformity to the Standards of SD memory card. If you format the SD card again, be sure to format it with the utility of TOSHIBA SD memory card format, not in the format defined as the Windows standard format.
Page 137: Removing An Sd Card
Optional Devices Removing an SD card To remove an SD card, follow the steps below. 1. In Windows XP, open the Safely Remove Hardware icon on the system tray and disable the SD card. 2. Push in the card and release it to pop the card out slightly. 3.
Page 138: Sd Card Care
Avoid the mat that generates static electricity. Use only memory modules approved by TOSHIBA. Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost.
Page 139: Installing Memory Module
Optional Devices Installing memory module To install a memory module, make sure the computer is in boot mode then: 1. Turn the computer off in boot mode. Refer to the Turning off the power section in Chapter 3, Getting Started. 2.
Page 140 Optional Devices 7. Lift up the back of the keyboard, rotate it toward you and lay in face down on the palm rest. When you move the keyboard forward, do not touch the keys. Doing so could cause misalignment. Hold the keyboard by the sides and lay it gently on the palm rest.
Page 141: Removing Memory Module
Optional Devices Removing memory module To remove the memory module, make sure the computer is in boot mode then: 1. Turn the computer off and remove all cables connected to the computer. 2. Turn the computer upside down and remove the battery pack (refer to Chapter 6, Power and Power-Up Modes.) 3.
Page 142: Additional Battery Pack
Optional Devices 7. Rotate the keyboard back into place and secure the keyboard brace as described in the previous section. 8. Turn the computer upside down and replace the battery pack. Additional battery pack You can increase the portability of the computer with additional battery packs.
Page 143: Removing
Optional Devices Removing To remove the secondary battery from the adaptor, follow the steps below. 1. Slide the latch in the direction of the arrow shown below. 2. Push the secondary battery pack up from the bottom and lift it out. Removing the secondary battery pack from the adaptor Universal AC adaptor If you frequently transport the computer between different sites such as...
Page 144: Removing The Hdd Pack
Optional Devices Removing the HDD pack To remove the HDD pack, follow the steps below and refer to the figures below. 1. Set the computer to boot mode and turn off the power. 2. Disconnect the AC adaptor and all external cables connected to the computer.
Page 145: Slim Selectbay Hdd Adaptor
Optional Devices Installing the HDD pack To install the HDD pack, follow the steps below. 1. Insert the HDD pack into the slot. 2. Fold over the plastic tab so that it goes into the HDD pack slot. Press to ensure a firm connection. Installing the HDD pack 3.
Page 146: Usb Diskette Drive
Optional Devices 2. Insert the HDD and push forward to ensure a firm connection. Installing the HDD 3. Close the lid and slide the lock to the lock position. Closing the lid For details on installing the Slim SelectBay HDD adaptor in the Slim SelectBay, refer to Chapter 4, Operating Basics.
Page 147: Advanced Port Replicator Ii
Optional Devices Advanced Port Replicator II In addition to the ports available on the computer, the Advanced Port Replicator II provides, audio line-out jack, line-in jack and separate ports for PS/2 mouse and PS/2 keyboard. The Port Replicator connects directly to the docking interface on the bottom of the computer.
Page 148: External Monitor
Optional Devices External monitor An external analog monitor can be connected to the external monitor port on the computer and Slim Port Replicator. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. If an external monitor is connected to the computer, do not connect the Slim Port Replicator.
Page 149: I.link (Ieee1394) Devices
There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. ■ Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.
Page 150: Connecting
Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. Connecting the i.LINK cable 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■...
Page 151: Security Lock
Optional Devices Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the left side of the computer.
Page 152: Chapter 9 Troubleshooting
Troubleshooting Portégé M100 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 153: Preliminary Checklist
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.
Page 154: Hardware And System Checklist
Troubleshooting Software The problems may be caused by your software or diskette. If you cannot load a software package, the media (usually a diskette) may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation.
Page 155: System Start-Up
This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■...
Page 156: Power
Troubleshooting Power When the computer is not plugged into an AC outlet, the battery pack is the primary power source. However, your computer has a number of other power resources, including intelligent power supply, Real Time Clock battery. These resources are interrelated and any one could affect apparent power problems.
Page 157 Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. Portégé M100...
Page 158: Password
Troubleshooting Password Problem Procedure Cannot enter Refer to the Password section in Chapter 6, password Power and Power-Up Modes. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard and Chapter 7, HW Setup. Problem Procedure Some letter keys...
Page 159: Lcd Panel
Troubleshooting LCD panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup, for more information. Problem Procedure Press hotkeys Fn + F5 to change the display No display priority, to make sure it is not set for an external monitor.
Page 160: Dvd-Rom Drive
Troubleshooting DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access Make sure the drive's drawer is securely closed. a CD/DVD in the Press gently until it clicks into place. drive Open the drawer and make sure the CD/DVD is properly seated.
Page 161: Cd-Rw/Dvd-Rom Drive
Cannot write If you have trouble writing, make sure you are correctly observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording.
Page 162 Chapter 2, The Grand Tour. Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■...
Page 163: Diskette Drive
Troubleshooting Diskette drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure Drive does not There may be a faulty cable connection. Check operate the connection to the computer and to the drive. Some programs run The software or hardware configuration may be correctly but others causing a problem.
Page 164: Printer
Troubleshooting Printer Refer to the troubleshooting and other relevant sections in your printer and software documentation. Problem Procedure Printer does not turn Check that the printer is connected to an electric outlet. Make sure the outlet is supplying power by plugging in an appliance. Computer/printer do Make sure the printer is turned on and is online not communicate...
Page 165: Pc Card
Troubleshooting PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation.
Page 166: Sound System
Troubleshooting Sound system Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. Check Windows Device Manager. Make sure the sound function is enabled and that settings for I/O address, Interrupt level and DMA are correct for your software and do not conflict with other hardware devices that you may have connected...
Page 167: Modem
Troubleshooting Modem Problem Procedure Communication Make sure the computer’s internal modem software can't settings are correct. Refer to Modem Properties initialise modem in the Control Panel. You can hear a dial If the call is going through a PBX machine, make tone but can't make sure the communication application’s tone dial a call...
Page 168: Standby/Hibernation
Troubleshooting Standby/Hibernation Problem Procedure Is Windows Media™ Player open? The system The system will not might not enter Standby/Hibernation, if Windows enter Standby/ or finished playing a selection. Close Windows Hibernation Media Player before you select Standby/Hibernation. Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules.
Page 169: Wireless Lan
Troubleshooting Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Make sure the computer’s wireless Wireless LAN communication switch is set to on. If problems persist, consult your LAN administrator.
Page 170: If You Need Further Assistance
They are your best sources for current information and support. Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed in Appendix C. Portégé M100 9-19...
Page 171: Appendix A Specifications
Specifications Portégé M100 Appendix A Specifications This appendix summarises the computer’s technical specifications. Physical dimensions Size With TFT display 270 (w) x 248 (d) x 31.7/37.4 (h) millimetres 2.00kg typical*, configured with:12.1"XGA-TFT, Weight 256MB RAM, 40GB HDD, DVD-ROM drive, Wireless LAN (Intel) * Weight will vary depending on whether or not and what kind of options are adopted.
Page 172: Environmental Requirements
Specifications Environmental Requirements Conditions Ambient Relative humidity temperature Operating 5°C to 35°C 20% to 80% Non-operating -20°C to 65°C 10% to 90% Thermal Gradient 20°C per hour maximum Wet-bulb 26°C maximum temperature Conditions Altitude (from sea level) Operating -60 to 3,000 metres Non-operating -60 to 10,000 metres maximum Power Requirements...
Page 173 Specifications Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analogue only) Type of dialling Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication Data: Full duplex system Fax: Half duplex Data Communication...
Page 174: Appendix B Ac Power Cord And Connectors
AC Power Cord and Connectors Portégé M100 Appendix B AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country in which it is used. All cords must meet the following specifications: Length: Minimum 2 metres...
Page 175 AC Power Cord and Connectors Italy: The Netherlands: KEMA Norway: NEMKO Sweden: SEMKO Switzerland: United Kingdom: DENANHO Japan: In Europe, power cords must be VDE type, H05VVH2-F and two conductor. For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-15P (125 V) as designated in the U.S.
Page 176: Appendix C The Toshiba International Warranty
TOSHIBA representation for registration. On the following pages is a list of the TOSHIBA companies who can be contacted if a claim on the warranty needs to be made. If users need further addresses in Eastern Europe or outside Europe, these are available from the national or European companies.
Page 177 Estonia ServiceNet EE Tel: +372-6504-949 Pärnu str. 142 Fax: +372-6504-948 11317 Tallinn http://www.servicenet.ee Finland Scribona Suomi OY / Toshiba Digital Media Tel: +358-9-5272555 Sinimäentie 8A,P.O.Box 83 Fax: +358-9-5272500 02630 ESPOO http://www.toshiba-dm.com France Toshiba Systèmes (France) S.A. Tel.: +33-8 92 69 70 92 7 Rue Ampère ;...
Page 178 The TOSHIBA International Warranty Ireland Toshiba Information Systems (U.K.) Limited, Tel.: +353 (0)1248 1 248 Toshiba Court, Weybridge Business Park, Fax: + 44 (0)8702 202 303 Addlestone Road, Weybridge, Surrey KT15 2UL www.toshiba.co.uk/computers/ Israel Mafil Technologies (3000) Ltd Tel: +972-3-918-3333...
Page 179 The TOSHIBA International Warranty Oman Bahwan IT Tel.: + 968 790191-117 Sarco Building, Ground Floor No. 459, Way Fax: +968-790 192 (Sultanate of Oman) No. 3109 Al Noor Street, http://www.bahwanit.com Ruwi 113 Muscat AC Serwis Sp. Z o. o. ul.
Page 180 Kingdom Toshiba Court, Weybridge Business Park Fax: + 44-(0)8702 202303 Addlestone Road, Weybridge www.toshiba.co.uk/computers/ Surrey KT15 2UL United States Toshiba America Information Systems, Inc. Tel: +1-949-583-3000 9740 Irvine Blvd., P.O. Box 19724 Fax: +1-949-583-3345 Irvine, CA 92713-9724 http://www.toshiba.com CT Computers d.o.o.
Page 181 The TOSHIBA International Warranty TOSHIBA addresses for the Internet/World Wide Web TOSHIBA Europe TOSHIBA Japan http://www.toshiba-europe.com http://www.toshiba.co.jp TOSHIBA America TOSHIBA Canada http://www.toshiba.com http://www.toshiba.ca Portégé M100...
Page 182: Appendix D Keyboard Layouts
Keyboard Layouts Portégé M100 Appendix D Keyboard Layouts Belgian Danish User's Manual Portégé M100...
Page 183 Keyboard Layouts French German Italian Portégé M100...
Page 184 Keyboard Layouts Norwegian Polish Portuguese Portégé M100...
Page 185 Keyboard Layouts Spanish Swedish Swiss-German Portégé M100...
Page 186 Keyboard Layouts UK English US English Portégé M100...
Page 187: Appendix E Display Controller And Modes
Display Controller and Modes Portégé M100 Appendix E Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides XGA and SXGA graphics modes support for the internal LCD and external monitors.
Page 188 Display Controller and Modes Video modes (VGA) Video Type Resolution Character Scanning mode matrix colours colours frequency (pels) vertical 0, 1 40 × 25 Characters 8 × 8 16 of 256K 16 of 256K Text 2, 3 80 × 25 Characters 8 × 8 16 of 256K 16 of 256K Text...
Page 189 Display Controller and Modes Video modes (SVGA) Resolution LCD colours CRT colours Vertical frequency (Hz) 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K (Virtual) 1400 × 1050 256/256K 256/256K (Virtual) 1600 ×...
Page 190 Display Controller and Modes Resolution LCD colours CRT colours Vertical frequency (Hz) 1400 × 1050 64K/64K 64K/64K (Virtual) 1600 × 1200 64K/64K 64K/64K (Virtual) 1920 × 1440 64K/64K 64K/64K (Virtual) 2048 × 1536 64K/64K 64K/64K 640 × 480 16M/16M 16M/16M 800 ×...
Page 191: Appendix F If Your Computer Is Stolen
What is your address, phone, and fax number? To register the theft, please follow these procedures: ■ Fill in the TOSHIBA Theft Registration form (or a copy of it) on the next page. ■ Attach a copy of your receipt showing where your computer was purchased.
Page 192: Toshiba Theft Registration
If your computer is stolen TOSHIBA Theft Registration Send to: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany Fax number: +49 (0) 941 7807 925 Country stolen: Machine type: (e.g. Portégé M100) Model number: (e.g. PXXXXX YXT) Serial number: (e.g.
Page 193: Appendix G Ascii Character Codes
ASCII Character Codes Portégé M100 Appendix G ASCII Character Codes This appendix shows the American Standard Code for Information Interchange (ASCII) on the following pages. The characters in the IBM char column appear on your display when you type the corresponding ASCII code (as described in Chapter 5, The Keyboard).
Page 194 ASCII Character Codes Sort Ctrl code code char char ¶ § ▲ ▼ Portégé M100...
Page 195 ASCII Character Codes Sort Sort code code char code code char space “ & ’ < > Portégé M100...
Page 196 ASCII Character Codes Sort Sort code code char code code char ’ Ç ü é â ä à å ç ê ë è ï î ì Ä Å É æ Æ ô ö ò û ù ÿ Ö Ü ¢ £...
Page 197 ASCII Character Codes Sort Sort code code char code code char á í ó ú ñ Ñ ¿ ¡ « » Portégé M100...
Page 198 ASCII Character Codes Sort code code char ß Portégé M100...
Page 199: Appendix H Internal Modem Guide
Internal Modem Guide Portégé M100 Appendix H Internal Modem Guide This appendix describes how to install and the remove the internal modem. Do not remove the base cover except to remove or install the internal modem or to check the PTT label. Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described.
Page 200: Removing The Internal Modem
Internal Modem Guide 7. Align the connectors and seat the modem board. 8. Secure the modem board with two screws. 9. Connect the modem cable. 10. Seat the palm rest and secure it with three screws. 11. Connect the keyboard cable and seat the keyboard. 12.
Page 201: Appendix I Wireless Lan
Portégé M100 Appendix I Wireless LAN This appendix describes Wireless LAN features and TOSHIBA Wireless LAN card specifications. For details on Wireless LAN settings, refer to the LAN Card Settings and Client Manager help file. These references have the latest information.
Page 202: Radio Characteristics
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN Wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Page 203 Subject to the radio regulations that apply in your country, your Wireless LAN Card may support a different set of 5GHz / 2.4GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in your country/region.
Page 204 Wireless LAN Wireless IEEE 802.11 Channels Sets (Revision A) Frequency Range 5150-5850 MHz Note Channel ID 5180 5200 5220 5240 5260 5280 5300 5320 5745 US only 5765 US only 5785 US only 5805 US only Available Area: US (USA, CANADA) only A peer-to-peer mode is available under the following condition;...
Page 205 Wireless LAN Wireless Channels Sets (Turbo Mode) Frequency Range 5150-5850 MHz Note Channel ID 5210 US only 5250 US only 5290 US only 5760 US only 5800 US only Available Area: US (USA, CANADA) only A peer-to-peer mode is available under the following condition: A Wireless LAN card receives a “US county/region code”...
Page 206: Glossary
Glossary The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference. AccuPoint II: A pointing device integrated into the TOSHIBA computer keyboard. adaptor: A device that provides an interface between two dissimilar electronic devices.
Page 207 Glossary asynchronous: Lacking regular time relationship. As applied to computer communications, asynchronous refers to the method of transmitting data that does not require a steady stream of bits to be transmitted at regular time intervals. AUTOEXEC.BAT: A batch file that executes a series of MS-DOS commands and programs each time you start the computer.
Page 208 Glossary cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time.
Page 209 Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
Page 210 Glossary data bits: A data communications parameter controlling the number of bits (binary digits) used to make up a byte. If data bits = 7 the computer can generate 128 unique characters. If data bits = 8 the computer can generate 256 unique characters. data: Information that is factual, measurable or statistical that a computer can process, store, or retrieve.
Page 211 Glossary echo: To send back a reflection of the transmitted data to the sending device. You can display the information on the screen, or output it to the printer, or both. When a computer receives back data it transmitted to a CRT (or other peripheral device) and then retransmits the data to printer, the printer is said to echo the CRT.
Page 212 The computer’s feature in which certain keys in combination with the extended function key, Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. Portégé M100...
Page 213 Glossary I/O devices: Equipment used to communicate with the computer and transfer data to and from it. I/O: Input/output. Refers to acceptance and transfer of data to and from a computer. icon: A small graphic image displayed on the screen or in the indicator panel.
Page 214 Glossary level 2 cache: See cache. Light Emitting Diode (LED): A semiconductor device that emits light when a current is applied. Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of glass coated with transparent conducting material. The viewing- side coating is etched into character forming segments with leads that extend to the edge of the glass.
Page 215 Glossary motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions. Sometimes called a main board. MPEG: Moving picture coding expert group is an industry standard architecture for compression of video signals.
Page 216 Glossary parallel interface: Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface. parallel: Refers to two or more processes or events that can occur simultaneously, and without interfering with each other. See also serial.
Page 217 A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. RAMDRIVE: Part of the computer’s random access memory assigned to simulate a disk.
Page 218 Glossary SCSI: Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices. serial communications: A communications technique that uses as few as two interconnecting wires to send bits one after another. serial interface: Refers to a type of information exchange that transmits information sequentially, one bit at a time.
Page 219 Glossary USB: The Universal Serial Bus is a way to connect up to 127 devices through one connector. A new development in 1997, this offers significantly improved ease of use and reliability than earlier expansion methods. VGA: Video graphics array is an industry standard video adaptor that lets you run any popular software.
Page 220: Index
Index Portégé M100 Index AC adaptor Cache memory connecting, 3-6 CPU cache, 1-3 AC adaptor, 1-5 level 2 cache, 1-3 AccuPoint II, 1-5 computer precautions, 4-2 cleaning, 4-26 problems, 9-13 moving, 4-26 using, 4-1 Cooling, 1-10 ASCII characters, 5-9, G-1 DC IN 15V battery, 6-4 indicator, 6-3...
Page 221 Index Hard disk drive, 1-4 LAN, 1-7, 4-20 problems, 9-8 Ethernet LAN, 1-7 Hibernation, 1-10 Hot keys, 5-4 Memory, 1-3 Hotkey, 1-9 expansion, 1-13 HW Setup, 7-1 microphone accessing, 7-1 using, 4-22 boot priority, 7-4 modem CPU, 7-3 installing, H-1 device config, 7-2 problems, 9-16 display, 7-3...
Page 222 9-13 Real Time Clock, 9-18 Toshiba Utilities, 1-8 SD card, 9-14 Troubleshooting, 9-1 sound system, 9-15 support from TOSHIBA, 9-19 system start-up, 9-4 using optical media drives, 4-5 power sources, 9-5 USB, 9-15 video modes, E-1 wireless LAN, 9-18...

Toshiba Portege M100 User Manual

Chapter 1 Introduction

Chapter 2 The Grand Tour

Chapter 3 Getting Started

Chapter 4 Operating Basics

Chapter 5 The Keyboard

Chapter 6 Power and Power-Up Modes

Chapter 7 HW Setup

Chapter 8 Optional Devices

Chapter 9 Troubleshooting

Appendix A Specifications

Appendix B AC Power Cord and Connectors

Appendix C the TOSHIBA International Warranty

Appendix D Keyboard Layouts

Appendix E Display Controller and Modes

Appendix F if Your Computer Is Stolen

Appendix G ASCII Character Codes

Appendix H Internal Modem Guide

Appendix I Wireless LAN

Quick Links

Related Manuals for Toshiba Portege M100

Summary of Contents for Toshiba Portege M100