Table of Contents
Advertisement
Programming the Remote
Channel Control Punch-Through
The AVR 3000's remote may be programmed to
operate so that the channel control function for
either the TV, cable or satellite receiver used in
your system may be used in conjunction with one
of the other devices controlled by the remote. For
example, while using and controlling the VCR,
you may wish to change channels on a cable box
or satellite receiver without having to change the
device selected by the AVR 3000 or the remote.
To program the remote for Channel Control
Punch-Through, follow these steps:
1. Press the Input Selector button
device you wish to have the channel control asso-
ciated with and the Mute button
same time until the red light illuminates under the
Input Selector
and the Program/SPL
Indicator
flashes amber.
2. Press the Volume Down button
Program/SPL Indicator
will stop flashing
and stay amber.
3. Press and release the AVR
or Input
Selector button
for the device that will be
used to change the channels. The Program/SPL
Indicator
will blink green three times and
then go out to confirm the data entry.
Example: To control the channels using your TV
while the remote is set to control the VCR, first
press the VID 1/VCR Input Selector button
and the Mute button
at the same time. Next,
release them and press the Volume Down but-
ton
, followed by the VID 2/TV Input
Selector button
.
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original con-
figuration, repeat the steps shown in the example
above. However, press the VID 1/VCR Input
Selector in Steps 1 and 3.
Transport Control Punch-Through
The AVR 3000's remote may be programmed to
operate so that the Transport Control Functions
(Play, Stop, Fast Forward, Rewind, Pause and
Record) for a VCR, DVD or CD will operate in con-
junction with one of the other devices controlled
by the remote. For example, while using and con-
trolling the TV, you may wish to start or stop your
VCR or DVD without having to change the device
selected by the AVR 3000 or the remote. To pro-
gram the remote for Transport Control Punch-
Through, follow these steps:
for the
1. Press the Input Selector
you wish to have the channel control associated
at the
with and the Mute button
until the red light illuminates, under the Input
Selector
and the Program/ SPL Indicator
flashes amber.
. The
2. Press the Play button
Indicator
will stop flashing and stay amber.
3. Press and release the AVR
Selector button
used to change the channels. The Program/SPL
Indicator
will blink green three times and
then go out to confirm the data entry.
Example: To control the transport of a CD player
while the remote is set to control the TV, press the
VID 2/TV Input Selector button
Mute button
at the same time. Next, release
them and press the Play button
the CD Input Selector button
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original con-
figuration, repeat the steps shown in the example
above. However, press the VID 2/TV Input
Selector in Steps 1 and 3.
NOTE: Before programming the remote for
Volume, Channel or Transport Punch-Through,
make certain that any programming needed for
the specific TV, CD, DVD, Cable or Satellite
Receivers has been completed.
Resetting the Remote Memory
As you add components to your home-theater sys-
tem, occasionally you may wish to totally repro-
gram the remote control without the confusion of
any commands, macros or "Punch-Through" pro-
gramming that you may have done. To do this, it is
possible to reset the remote to the original factory
defaults and command codes by following these
steps. Note, however, that once the remote is
reset, all commands or codes that you have
entered will be erased and will need to be re-
entered:
for the device
1. Press any of the Input Selector buttons
and the "O" button
at the same time
the Program/SPL Indicator
amber.
2. Press the "3" button
3. The red LED under the Input Selector
. The Program/SPL
go out and the Program/SPL Indicator
stop flashing and turn green.
or Input
4. The Program/SPL Indicator
for the device that will be
green until the remote is reset. Note that this may
take a while, depending on how many commands
are in the memory and need to be erased.
5. When the Program/SPL Indicator
out, the remote has been reset to the factory set-
tings.
and the
, followed by
.
at the same time until
begins to flash
three times.
will
will
will remain
goes
PROGRAMMING THE REMOTE 39
Hide quick links:
Advertisement
Table of Contents
