Table of Contents
Advertisement
Advanced Features
Semi-OSD Settings
The semi-OSD system places one line messages
at the lower third of the video display screen
whenever the Volume, Input Source, Surround
mode or tuner frequency of any of the configura-
tion settings are changed. The semi-OSD system
is helpful in that enables you to have feedback
on any control changes or remote commands
using the video display when it is difficult to
view the front-panel displays. However, you may
occasionally prefer to turn these displays off for
a particular listening session. You may also want
to adjust the length of time the displays remain
on the screen. Both of those options are possible
with the AVR 3000.
To turn off the semi-OSD system, you will need
to make an adjustment in the ADVANCED
SELECT menu (Figure 9). To start the
adjustment, press the OSD button
the MASTER MENU to the screen. Press
the
Button
twice, until the on-screen
cursor is next to the ADVANCED line.
Press the Set Button
to enter the
ADVANCED SELECT menu.
At the ADVANCED SELECT menu
make certain that the on-screen
to the S E M I O S D line by pressing the
buttons
as needed. Next, press the
ton
so that the word O F F is highlighted
in the video display.
Note that this setting is temporary and will
remain active only until it is changed or until the
AVR 3000 is turned off. Once the unit is turned
off, the semi-OSD displays will remain activated,
even if they were switched off for the previous
listening session.
To change the length of time that the semi-OSD
displays remain on the screen, go to the
ADVANCED SELECT Menu as out-
lined earlier, and press the
needed, until the on-screen
the SEMI-OSD T I M E O U T line. Next,
press the
Buttons
/
time in seconds is displayed. Note that unlike
most of the other options in this menu, this is a
permanent setting change, and the time-out
entry will remain in effect until it is changed,
even when the unit is turned off.
to bring
If you wish to make other adjustments in the
menu, press the
screen
cursor is next to the desired setting or
the RETURN TO M E N U line and press
the Set button
ments to make, press the OSD Button
exit the menu system.
cursor is next
/
but-
buttons
as
/
cursor is next to
until the desired
Buttons
until the on-
/
. If you have no other adjust-
to
Full-OSD Time Out Adjustment
The FULL-OSD menu system is used to
simplify the setup and adjustment of the AVR
3000 using a series of on-screen menus. The fac-
tory default setting for these menus leaves them
on the screen for 20 seconds after a period of
inactivity before they disappear from the screen
or Time Out. This Time Out is a safety measure to
prevent the menu text from burning into the
CRTs in your monitor or projector, which might
happen if they were left on indefinitely. However,
some viewers may prefer a slightly longer or
shorter period before the Time Out display.
To change the Full-OSD Time Out, you will need
to make an adjustment in the ADVANCED
SELECT Menu (Figure 1). To start the
adjustment, press the OSD button
the MASTER MENU to the screen. Press
the
button
twice, until the on-screen
cursor is next to the ADVANCED line.
Press the Set Button
to enter the
ADVANCED SELECT Menu (Figure 9).
At the ADVANCED SELECT menu
make certain that the on-screen
to the FULL-OSD T I M E O U T line by
pressing the
Buttons
as needed. Next,
/
press the
buttons
until the desired
/
time is displayed in seconds. Note that unlike
most of the other options in this menu, this is a
permanent setting change, and the time-out
entry will remain in effect until it is changed,
even when the unit is turned off.
If you wish to make other adjustments in the
menu, press the
Buttons
/
screen
cursor is next to the desired setting or
the RETURN TO M E N U line and press
the Set button
. If you have no other adjust-
ments to make, press the OSD Button
exit the menu system.
ADVANCED FEATURES 35
to bring
cursor is next
until the on-
to
Hide quick links:
Advertisement
Table of Contents
