Table of Contents INFORMATION TO USER : Parts This equipment has been tested and found to comply with the limits of a Class Connection to Signal Source B digital device, pursuant to Part 15 of the FCC Rules. The range of control Angle These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can Name and Function of Front...
Good Posture Guide Parts Place the monitor to face the user and then adjust the monitor angle. Take a break (for about 10 minutes) at every hour during the work with monitor. Refer to the following figure to take the correct posture. Look down the monitor below the horizon.
Connection to Signal Source The range of control Angle Basic Connection How to Adjust the Stand Port for AC power cable. Port for BNC input Port for S-VHS input Port for signal cable from signal source. Kensington Lock Forward 4 <...
Name and Function of Front Front panel Functions Power button Power button is located in the lower center of the Front Bezel. You can push the button to turn on/off the power. Power Indicating LED Dark : Power off Green : Normal mode Green blinking : DPMS mode or Check Signal Cable mode.
Adjusting OSD Power Management Feature PC MODE The monitor is equipped with a power saving circuit that confirms to the world-standard Display Power Manager Signalling Brightness / Contrast (DPMS) mode of Video Electronics Standard Association (VESA). The power management feature requires that the video card of the MENU SELECT computer should support DPMS function.
Clock Phase Phase SELECT MENU SELECT 1. Press the MENU button to access main menu. 1. Press to move Phase ICON. 2. Use to move CLOCK PHASE ICON. 2. Use SELECT button to select it. 3. Press SELECT button into the submenu. 3.
OSD H-Position Preset Color MENU SELECT 1. Use to select the Mode 1, and Mode 2. 1. Use to move OSD H-Position ICON. 2. Press the Menu button to return previous state. 2. Press SELECT button to select it. 3. Use to adjust OSD left or right.
Special Language MENU SELECT MENU SELECT 1. Use to move Language ICON. 1. Press the MENU button to access main menu. 2. Press SELECT button to select it. 2. Use to move Special ICON. 3. Use to select language. 3. Press SELECT button into the submenu. Factory Reset SELECT 1.
Adjusting OSD CVBS, S-VIDEO MODE Brightness / Contrast Image MENU SELECT SELECT 1. Press the MENU button to access main menu. 1. Press the MENU button to access main menu. 2. Use -,+ to move IMAGE menu. 2. Use to move Brightness / Contrast ICON. 3.
Aspect Ratio (CVBS,S-VIDEO Mode) SELECT SELECT 1. Use -,+ to move ASPECT RATIO menu. 1. Use to select the HUE ICON. 2. Press the SELECT button to select it. 2. Press SELECT button to select it. 3. Use -,+ to select 4:3 or 5:4. 3.
Page 12
OSD V-Position User Color SELECT SELECT MENU 1. Use to move OSD V-Position ICON. 1. Use to move User color ICON. 2. Press SELECT button to select it. 2. Press SELECT button to select it. 3. Use to adjust OSD upward or downward. 3.
Standard Signal Table PC Supported Mode Factory Reset Horizontal Frequency Vertical Frequency Clock Frequency Resolution (KHz) (Hz) (MHz) (720 X 400) 28.322 31.469 70.087 SELECT (640 X 480) 25.175 31.469 59.940 31.500 1. Use to move the Factory Reset ICON. (640 X 480) 37.500 75.000...
Troubleshooting Specification IK-H550V(B15AC) Model Type Amorphous active matrix super TFT LCD Power LED is dark. Check the power connection. No picture. Screen Size 38.1cm (Diagonal) (Refer to page 4) Maximum Resolution 1024 X 768 @ 75 Hz Pixel Range 0.297 mm X 0.297 mm Display Colors 16.2M Color...
Warning To prevent damage or loss, please read this warning carefully. When connecting/disconnecting the plug, pull out Adjust COLOR at User Mode in OSD Color Color is irregular. the plug itself, and never pull the cord to prevent fire Menu. caused by short.