Page 1
35668-9401 Better Products. Better Value. GAS HOB INSTRUCTION BOOKLET - INSTALLATION AND SERVICING INSTRUCTIONS MODEL NOS. HG 250...
Page 2
Refer to your local appliance. Children should be supervised at all Tricity Bendix Service Centre. Always insist on genuine Tricity Bendix spare parts. times and should not be allowed to touch the hot surface or be in the vicinity when in use or until the appliance has cooled after use.
Description of the Appliance Page Operation Page Maintenance and Cleaning Page Help us to help You Page Tricity Bendix Service Force Addresses Page Guarantee for 12 Months Page SECTION 2 - Instructions for the Installer - Technical Data Page Installation Page...
INSTRUCTIONS FOR THE USER This appliance meets the requirements laid down INSTALLATION in EEC directive No. 89/336 relating to the It is mandatory that all operations required for the suppression of radio and TV interferences. installation are carried out by a Competent Gas Installer (CORGI registered installers normally meet this criteria), and in accordance with existing rules WHEN THE HOB IS FIRST INSTALLED...
160 mm. 240 mm. If the control knobs become difficult to turn, Medium (semirapid) 120 mm. 220 mm. please contact your local Tricity Bendix Service Small (Auxiliary) 80 mm. 160 mm. Centre. MAINTENANCE AND CLEANING Before any maintenance or cleaning can be...
CUSTOMER RELATIONS DEPARTMENT In the event of your appliance requiring servive For general enquiries concerning your Tricity Tricity Bendix have an arrangement with Bendix appliance, or further information on Electrolux Group Service. Before calling out an Cookers, Microwaves, Refrigeration or Home...
TRICITY BENDIX SERVICE FORCE POSTCODE TO SERVICE CENTRE CROSS REFERENCE Postcode Telephone Service Centre Postcode Telephone Service Centre Postcode Telephone Service Centre 01224-696569 Aberdeen 0181-9659699 Canvey PL1-9, 16, 19-21 01626-65909 Newton Abbott 0113-2608511 Leeds PL10-15, 17, 18 0181-965 9699 Canvey...
Page 8
TRICITY BENDIX SERVICE FORCE ADDRESSES CENTRE ADDRESS CENTRE ADDRESS CENTRE ADDRESS INVERNESS Tricity Bendix Service Force ABERDEEN Tricity Bendix Service Force NORTHERN Tricity Bendix Service Force Northeast Appliance Service George Ross PO Box 40 Preston Road 8 Cornhill Arcade Forrestry Workshop...
. any light bulbs or removable parts of glass or We, Tricity Bendix undertake that if, within the plastic. 12 months of the date of the purchase, this Tricity Bendix appliance or any part thereof is...
INSTRUCTIONS FOR THE INSTALLER - TECHNICAL DATA OVERALL DIMENSIONS CUT OUT DIMENSIONS Width: 580 mm. Width: 550 mm. Depth: 510 mm. Depth: 470 mm. Thickness: 40 mm. Height: 88 mm. Weight: 11 Kg. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 240V 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse.
INSTALLATION IMPORTANT Rectangular cut-out size for hob It is essential that a competent installer is employed to fit this appliance. The manufacturer will not accept liability, should the above instruction or any of the other safety instructions incorporated in this book be ignored. On the end of the shaft, which includes the GJ 1/2"...
INSTALLATION ABOVE CUPBOARD OR DRAWER If the hob is to be installed above a cupboard or It is also recommended to carry out the electrical drawer it will be necessary to fit a heat resistant connection to the hob as shown in illustrations A board below the base of the hob on the and B.
IMPORTANT SAFETY REQUIREMENTS This appliance must be installed in accordance LOCATION with the Gas Safety (Installation and Use) The hob may be located in a kitchen, a kitchen/ Regulations (Current Edition) and the IEE Wiring diner or bed sitting room, but not in a bathroom Regulations (Current Edition).
ELECTRICAL CONNECTIONS All electrical connections must be carried out by When replacing the plug top fuse only a 3amp competent persons in accordance with the current BS1362 ASTA rated replacement should be used. regulations. This appliance is designed to be The plug must not be used if the fuse cover/carrier is connected to a 240V 50Hz AC electrical supply.
FAULT FINDING PRELIMINARY ELECTRICAL SYSTEMS SOCKET CHECK PLUG (with cover removed) (face view) Earth Wire Green/Yellow Blue Brown Green Yellow START Neutral Wire Isolate appliance Blue and carry out: A: Earth Continuity check. Blue Green Brown Yellow Carry out: Electricity supply Carry out: D: Resistance to should now be...
Page 17
IGNITION SYSTEM / GAS IGNITION Check gas supply at Ignitor does not spark burner Check plug top fuse and Light burner manually replace if necessary Check by pass simmer Check polarity and earth adjusted continuity of supply point Check position of the Check earth continuity electrode of appliance...
COMMISSIONING When the hob has been fully installed it will be a) Minimum adjust.screw necessary to check the minimum flame setting. b) Tap To do this, follow the procedure below. Turn the gas tap to the MAX position and ignite. Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
SERVICING A: Removal Of Hob Top D: Removal Of Burner 1. Remove the panstands and each burner cap and 1. Follow the procedures in Section A. crown. 2. With the aid a 12mm spanner loosen off the pipe 2. Lift the hob from off the working top. connection nut.
Page 20
Better Products. Better Value. TRICITY BENDIX, 99 OAKLEY ROAD, LUTON, BEDFORDSHIRE, LU4 9QQ. A Division od Emaco Limited - Registered in England No. 176547 - Registered Office. 101 Oakley Road, Luton LU4 9RJ. MODEL NO. PART NO. HG 250 35668-_____...
Need help?
Do you have a question about the HG 250 and is the answer not in the manual?
Questions and answers