Time; Changing The Basic Settings - Siemens HB64A Series Instruction Manual

Press the 0 sensor.
4.
The time when the dish will be ready and the end time
symbol y will be shown on the display panel.
Delay the end time using the
5.
Press the ºC sensor.
6.
Set the temperature or required grill power using the
sensors.
The programmed temperature and the
on the display panel, and the oven will be set to standby. When
the oven turns on, the programmed temperature and the
symbol will be shown. The
The cooking time has finished
A signal will sound. The oven will stop heating. The display
panel will show : . Press the
‹‹ ‹‹
cooking time can be set with the sensors
the 0 sensor and turning the control knob to zero. The oven
is off.

Changing the basic settings

This oven has different basic settings. The settings can be
adapted to the user's own needs.
Basic setting
Duration of signal after the cooking time or the
™‚
time set on the timer has elapsed
Time indicator
™ƒ
Time until a setting is applied
™„
The shelf support rails have been refitted.
™†
Select default settings for all values.
™‡
* Default setting
The oven must be switched off.
Press the sensor for approximately 4 seconds.
0
1.
The display panel will show the current basic setting for the
duration of the signal, e.g.,
Change the basic setting using the
2.
or sensors.
@ A
symbol will be shown
y
symbol turns off.
y
sensor twice . A new
0
or . Or pressing
@ A
Option .
™‚ ƒ
@ or A sensors.
Changing the end time
Press the sensor
the or sensors. The altered time is shown after a few
@ A
seconds. Do not change the end time if the cooking time has
already started to count down. The final result may not be the
same.
Cancelling the end time
Press the sensor three times and reset the end time to the
0
current time with the
Viewing the time settings
If several time functions are programmed, the corresponding
symbols light up on the display panel.
To view the timer
the time 0 , press the
symbol lights up. The corresponding value will be shown for a
few seconds on the display panel.

Time

Once the oven has been connected or after a power cut, the
0 and ‹ : ‹‹
clock to the right time.
Press the 0
1.
The time is displayed
Set the time with the
2.
Confirm the time with the
3.
The programmed time is displayed after a few seconds.
Changing the time
@ or A
No other time function must be programmed, the oven must be
switched off.
Press the
0
1.
x
The display panel displays
Set the time with the
2.
Confirm the time with the
3.
The programmed time is displayed after a few seconds.
Hiding the time
The time can be hidden. See the Modifying basic settings
chapter.
Option 0 Option 1
- approx. 10 sec
no yes*
- approx. 2 sec
no yes
no* yes
Confirm with the sensor
3.
The display panel shows the following basic setting. The
sensor allows you to run through all the settings and the
sensors allow you to modify them.
A
Finally, press the
4.
All basic settings have been applied.
The basic settings can be changed again at any time.
three times. Change the end time using
0
sensor. The oven switches on.
A
V , the cooking time x
0 sensor repeatedly until the required
symbols light up on the display panel.Set the
sensor.
: .
‚ƒ ‹‹
@ or A sensors.
sensor.
0
sensor twice.
.
0
or sensors.
@ A
0 sensor.
Option 2
approx. 2 min*
-
approx. 4 sec*
-
-
.
0
sensor for approximately 4 seconds.
0
, the end time y or
Option 3
approx. 5 min
-
approx. 10 sec
-
-
0
or
@
9