Switching The Attenuator; Switching The Input Signal Detection Setting; Reset (Factory Settings); When Other Equipment (Mini Component System, Av Amp, Etc.) Manufactured By Panasonic Operates With The Remote Control Operations Of This System - Panasonic SC-HTX5 Operating Instructions Manual

Switching the attenuator

Switch the attenuator "ON " when big sounds become distorted
while playing an analogue input source.
1. Press and hold [–SETUP, OFF] for about 2
seconds.
The setting items are displayed. (➜ page 21)
2. Press [w][q] to select "ATTENUATOR "
and press [OK].
3. Press [e][r] to select "ON " and press
[OK].
ON, OFF
Factory setting: OFF
4. Press [ RETURN] several times to select
"EXIT " and press [OK] to fi nish the
setting.
Switching the input signal
detection setting
Most sources can be played with "AUTO " (factory setting).
However, in the following cases, change the input signal
detection setting.
• When the beginning of the song is cut during playback of CD,
set to "PCM " (PCM FIX).
• When the signal is not detected during playback of DTS
sources, set to "DTS " (DTS FIX).
• When noise occurs, return the setting to "AUTO ".
1. Press and hold [–SETUP, OFF] for about 2
seconds.
The setting items are displayed. (➜ page 21)
2. Press [w][q] to select "INPUT MODE "
and press [OK].
3. Press [w][q] to select the input and press
[OK].
Input: TV, DVD, AUX1, AUX2, AUX3
4. Press [e][r] to select the detection
method of input signal and press [OK].
AUTO : Automatic detection
PCM : PCM (from CDs) digital input fixed
DTS : DTS digital input fixed
Factory setting: AUTO
Repeat steps 3 and 4 to change setting.
5. Press [ RETURN] several times to select
"EXIT " and press [OK] to fi nish the
setting.

Reset (factory settings)

The operation settings for the system will be initialized to the
settings made at the time of shipment.
1. Press and hold [–SETUP, OFF] for about 2
seconds.
The setting items are displayed. (➜ page 21)
2. Press [w][q] to select "RESET " and press
[OK].
3. Press [e][r] to select "YES " and press
[OK].
YES : Choice for resetting
NO : Choice against resetting
• To cancel, select "NO ".
Note
• All the settings are reset when you select "YES " and the input
selector automatically switches to "BD/DVD ".
• If you select "NO ", you will return to step 2. To exit setup
mode, press [ RETURN] a few times to display "EXIT ", and
then press [OK].
When other equipment (mini component
system, AV amp, etc.) manufactured
by Panasonic operates with the remote
control operations of this system
When using this system's remote control, other equipment
may operate. In this case, switch this system's remote control
code to "REMOTE 1 ". Do the following to set the same code
number for this system and remote control.
Setting this system
1. Press and hold [–SETUP, OFF] for about 2
seconds.
The setting items are displayed. (➜ page 21)
2. Press [w][q] to select "REMOTE " and
press [OK].
3. Press [e][r] to select "1 " and press [OK].
Factory setting: 2
• You cannot fi nish the setting mode until the setting on
the remote control is changed. Go to step 4.
• To set the remote control code to 2, select "2 " in step
3 and press [OK].
Setting the remote control
4. Press and hold [OK], and then press [TV]
(more than 2 seconds).
TV: Remote control code 1
BD/DVD: Remote control code 2 (factory setting)
• Select the same number as the code number you
have selected in step 3.
• To set the remote control code to 2, press and hold
[OK] in step 4, and then press [BD/DVD] more than 2
seconds.
5. Press [ RETURN] several times to select
"EXIT " and press [OK] to fi nish the
setting.
Note
If different codes are set between this system and remote
control, the error message "REMOTE 2 " or "REMOTE 1 " is
displayed.
23
RQT9478