Alto ENCORE R Operator's Manual
  1. Manuals
  2. Brands
  3. Alto Manuals
  4. Floor Machine
  5. ENCORE R
  6. Operator's manual

Alto ENCORE R Operator's Manual

American-lincoln technology
Hide thumbs Also See for ENCORE R:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual , Electrical Troubleshooting Manual
Operator's Manual
Instruction Book
Beginning with Serial Number 180337
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure
to read this book prior to operating or attempting any service or maintenance procedure to
your machine could result in injury to you or to other personnel; damage to the machine or to
other property could occur as well. You must have training in the operation of this machine
before using it. If you or your operator(s) cannot read English, have this manual explained
fully before attempting to operate this machine.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books, write to: American-Lincoln
Part No. 2-86-00315
AMERICAN-LINCOLN
ENCORE R
AMERICAN-LINCOLN
TECHNOLOGY
, 1100 Haskins Road, Bowling Green, Ohio 43402
2003
®
American-Lincoln
ENCORE R
ISO 9001
U L
®
#
FILE A2287
56041768
USA
Printed in the
1-1

Advertisement

Table of Contents
loading

Related Manuals for Alto ENCORE R

Summary of Contents for Alto ENCORE R

  • Page 1 AMERICAN-LINCOLN TECHNOLOGY Operator's Manual ENCORE R Instruction Book Beginning with Serial Number 180337 READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your machine could result in injury to you or to other personnel;...
  • Page 2 NOTE AMERICAN-LINCOLN ENCORE R...

  • Page 3: Table Of Contents

    MAINTENANCE 39 OPERATING INSTRUCTIONS 30 ORDERING PARTS 10 SAFETY PRECAUTIONS 11 SPECIFICATIONS 14 STANDARD HARDWARE & TORQUE VALUES 7 SYMBOLS 9 TROUBLESHOOTING 50 WIRE HARNESS CONNECTIONS 54 WIRE HARNESS CONNECTIONS-SPRAY WAND 58 WIRE HARNESS ROUTING & CONNECTIONS 56 AMERICAN-LINCOLN ENCORE R...

  • Page 4: Disclaimer

    No portion of this manual may be reproduced without the express written consent of: AMERICAN LINCOLN Product Engineering 1100 Haskins Road Bowling Green, OH, 43402 (419) 352-7511 Fax: (419) 373-4284 Copyright 2003 American Lincoln. All rights reserved. Printed in USA March 2003 AMERICAN-LINCOLN ENCORE R...

  • Page 5: Decimal-Metric Conversion Table

    DECIMAL-METRIC CONVERSION TABLE DECIMAL DECIMAL FRACTION MILLIMETER FRACTION MILLIMETER C-2001/9907 AMERICAN-LINCOLN ENCORE R...

  • Page 6: Hardware Abbreviations

    = Square Head Setscrew = Knurled Cup Point Setscrew -KCP = Cup Point Setscrew = Oval Point Setscrew = Full Dog Point Setscrew -FDP = Half Dog Point Setscrew -HDP = Flat Point Setscrew -COP = Cone Point Setscrew C-2004 AMERICAN-LINCOLN ENCORE R...
  • Page 7 F = Fine Thread * = Torque values for #6 through 1/4 are lb./in. All others are lb./ft. NOTE Decrease the torque by 20% when using thread lubricant The torque tolerance is ± on torque values. C2000/9905 AMERICAN-LINCOLN ENCORE R...
  • Page 8 92-100 1 5/16-12 200-220 1 11/16-12 125-140 1 5/8-12 210-280 2-12 150-165 1 7/8-12 270-360 * O-Ring face seal type end not defined for this tube size. NOTE Parts must be lightly oiled with hydraulic fluid. C-2002 AMERICAN-LINCOLN ENCORE R...

  • Page 9: Symbols

    Moving Fan Blade Pinch Point/Crush Hazard Power Recovery Tank High Cover or Hopper Could Close/ Engage Support Scrub Brush Down & On Turn Key Off/Lock Wheel Before Leaving Seat WARNING! / ATTENTION! Scrub Brush Up and Off AMERICAN-LINCOLN ENCORE R...

  • Page 10: Ordering Parts

    Fax: +1 416 6 75 69 89 E-mail: info@alto-nl.com Tel.: +1 704 971 1240 Fax: +1 704 971 1241 CROATIA NORWAY E-mail: info@altocsi.com Wap ALTO Strojevi za ciscenje, d.o.o. ALTO Norge A/S Siget 18a Bjørnerudveien 24 10020 Zagreb 1266 Oslo Tel.: +385 1 65 54 144 Tel.: +47 22 75 17 70...

  • Page 11: Safety Precautions

    Scrub deck presents hazard for crushing, entanglement, WARNING friction and abrasion ELECTRICAL HAZARD - Shocks can cause serious personal injury Disconnect battery before working in this area Repairs must be performed by authorized personnel only AMERICAN-LINCOLN 1-11 ENCORE R...

  • Page 12: Safety Precautions

    This machine is not at tow truck and should not be used for towing. • Do not use this machine as a step or furniture. • Do not operate machine on public highways, gravel, sand, grass and other unsafe surfaces. 1-12 AMERICAN-LINCOLN ENCORE R...
  • Page 13 Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. AMERICAN-LINCOLN 1-13 ENCORE R...

  • Page 14: Specifications

    Guaranteed power sound level: L max = 96 dBA (Operator) Sound pressure level: 77.2 dBA CHARGER Encore R (34” & 38”) 36 Volt output, 115V/60Hz or 230V/50Hz Input MOTORS, VACUUM 1 HP (.74 kW), 3 stage, tangential discharge MOTORS, BRUSH 1.7 hp (1.3kW)
  • Page 15 SPECIFICATIONS WIDTH Encore R (34”) Machine 33.5” (85 cm) Brush Housings 38.0” (96.5 cm) Squeegee 42.0” (106.7cm) Encore R (38”) Machine 33.5” (85 cm) Brush Housings 41.0” (104.1 cm) Squeegee 42.0” (106.7 cm) HEIGHT 51” (129.5 cm) HEIGHT W/OHG 80” (203.2 cm) WEIGHT Encore R (34”)
  • Page 16 SPECIFICATIONS 1-16 AMERICAN-LINCOLN ENCORE R...

  • Page 17: Machine Preparation

    UNPACKING AND ASSEMBLING MACHINE The Encore R is shipped on a pallet covered by a plastic bag and fastened with four hold down brackets. 1. Remove plastic bag. 2. Unbolt lag screws located on each corner of machine.
  • Page 18 Do not charge batteries on a concrete grounded surface. Hydrogen gas is formed during the charging operation and is explosive. Only charge batteries in a well ventilated area with the lid open. Avoid any smoking, open flame, or electrical sparks. 1-18 AMERICAN-LINCOLN ENCORE R...
  • Page 19 Connect battery connector wires in series to batteries as shown in figure 8. WARNING Do not leave charged batteries on concrete surface, they will discarge. AMERICAN-LINCOLN 1-19 ENCORE R...
  • Page 20 Plug the battery connector assembly from the battery to the machine connector assembly as shown in figure 10. Reinstall the side panel and then release the safety latch and lower the seat as shown in figure 11. 1-20 AMERICAN-LINCOLN ENCORE R...

  • Page 21: Controls

    Low Solution Light (Left) High Recovery Light (Right) Scrub Pressure Switch Squeegee Vacuum Switch Light Switch, Optional LCD Display Forward/Reverse Switch Key Switch Secondary Optional Brake Pedal (Bottom), Pedal Lock (Top) Horn Button, Optional Foot Throttle AMERICAN-LINCOLN 1-21 ENCORE R...
  • Page 22 LCD DISPLAY SCREEN CONTROL BUTTON The Encore R is equipped with an LCD display allowing the operator to monitor machine operation. The LCD display button is located in the center of the console to the right under the display. Pushing on the menu button enables the operator to view screen functions and monitor machine status and operation.
  • Page 23 Selected pressure is displayed as a bar on the LCD control panel. Pressing the scrub pressure switch down selects the next lowest setting available, decreasing pressure as shown in figure 17. AMERICAN-LINCOLN 1-23 ENCORE R...
  • Page 24 19. Pressing down on the foot throttle with the forward/reverse switch in the reverse position will raise the squeegee when it is down. The vacuum will turn off in 15 seconds after the squeegee is raised. 1-24 AMERICAN-LINCOLN ENCORE R...
  • Page 25 The high recovery red indicator light is located on the left side above the switches on the console to the right of the low solution indicator light as shown in figure 21. When the high recovery indicator light illuminates the recovery tank is full and needs to be drained and cleaned out. AMERICAN-LINCOLN 1-25 ENCORE R...
  • Page 26 The horn button is located on the floor of the operator’s compartment to the left of the optional parking brake peda as shown in figure 24. Pressing the button with the left foot will activate the horn. 1-26 AMERICAN-LINCOLN ENCORE R...
  • Page 27 The foot brake is not a method for slowing machine travel or for stopping under normal conditions. This is accomplished by releasing the foot throttle. AMERICAN-LINCOLN 1-27 ENCORE R...
  • Page 28 The hour meter is activated when the key switch is in the “on” position. Screen 2 on the LCD display shows total hours and panel screen display 3 shows total hours, brush hours and traction hours. This is useful for determining service intervals. 1-28 AMERICAN-LINCOLN ENCORE R...
  • Page 29 The machine will stop immediately if there is no operator present in the seat. HAND LEVER Fig. 29 PRE SWEEP (OPTION) The sweeper is designed to turn the broom on as it is lowered. To lower the broom release hand lever on right side. AMERICAN-LINCOLN 1-29 ENCORE R...

  • Page 30: Operating Instructions

    3. Push down on the foot throttle to obtain desired travel speed, release foot throttle to stop. WARNING Do not turn the steering wheel sharply when the machine is in motion. The sweeper is very responsive to movement of the steering wheel. Do not make sudden turns. 1-30 AMERICAN-LINCOLN ENCORE R...
  • Page 31 BRUSHES OFF IN NEUTRAL - Scrub brushes automatically disengage when machine is idle. PARKING BRAKE INTERLOCK - Parking brake will automatically set when foot pedal is released. AUTOMATIC RECOVERY VACUUM SHUT-OFF - Vacuum fans will shut down when recovery tank is full. AMERICAN-LINCOLN 1-31 ENCORE R...
  • Page 32 Sensors in each tank will indicate, by lights on the control panel, when the water in the solution tank is too low or when the water in the recovery tank is too high. 1-32 AMERICAN-LINCOLN ENCORE R...
  • Page 33 After scrubbing, the dirty solution is vacuumed from the floor and discharged into the recovery tank. At intervals, a float switch activates the recycling pump, which sends filtered solution from the recovery tank to the solution tank. AMERICAN-LINCOLN 1-33 ENCORE R...
  • Page 34 Discontinue the scrubbing cycle, put all controls in the forward position for transport and drive to the drain area. NOTE After stopping, perform these post operation checks. 1-34 AMERICAN-LINCOLN ENCORE R...
  • Page 35 The local city and state regulations regarding wastewater discharge may be in effect in your area. Understand and follow the regulations in your area. Be aware of the environmental hazards associated with the substances you dispose of. AMERICAN-LINCOLN 1-35 ENCORE R...
  • Page 36 Fig. 40 Fig. 41 Inspect the disc brushes and replace when bristles are reduced to 3/4 inch length as shown in figure 40 and 41. To order replacement brushes, see scrub brush options in this manual. 1-36 AMERICAN-LINCOLN ENCORE R...
  • Page 37 This process can be repeated until all four edges are worn. If the squeegee blade has become rippled, it will need to be replaced. Inspect the inner flap on the rear squeegee for wear and to ensure it has not been torn or damaged. AMERICAN-LINCOLN 1-37 ENCORE R...
  • Page 38 The filter bag should be checked every time the pre sweep is used and replaced when full as shown in figure WARNING There is a potential risk of the bag tearing and causing premature failure to the dust control motor and the main and side broom motor. 1-38 AMERICAN-LINCOLN ENCORE R...

  • Page 39: Maintenance

    American-Lincoln parts. Refer all Maintenance and Service Requirements to Qualified Maintenance Personnel. Do not attempt to service this machine until you have read and understood all Safety Warnings associated with the equipment you are working on. AMERICAN-LINCOLN 1-39 ENCORE R...
  • Page 40 If it becomes necessary to remove such equipment for repair or maintenance, this equipment must be reinstalled before machine is placed back in operation. 1-40 AMERICAN-LINCOLN ENCORE R...
  • Page 41 2. Insert charging plug into battery receptacle. 3. Plug power cord into proper AC source. 4. Follow the charging instructions provided on the charger. 5. Maintain electrolyte level in batteries, check after charging. Add distilled water as needed. AMERICAN-LINCOLN 1-41 ENCORE R...
  • Page 42 The battery box can slide off a forklift and cause severe personal injury or damage to equipment. Ensure that the battery box is properly secured to the forks of the forklift during transport, drive and stop with caution. 1-42 AMERICAN-LINCOLN ENCORE R...
  • Page 43 3. Unplug the battery connector assembly from the battery to the machine connector assembly. 4. Disconnect the battery connector wires from the batteries. Remove battery spacers holding batteries in place. 6. Use a 100 lb. (454 KG) lifting mechanism to lift and remove batteries. AMERICAN-LINCOLN 1-43 ENCORE R...
  • Page 44 (See replacing the scrub brushes) To change pad follow this procedure. 1. The pad driver is held in place by a ring. Pull the pad driver straight down to remove it. 2. Remove the pad holder using the spring wire retainer. 3. Replace the worn pad. 1-44 AMERICAN-LINCOLN ENCORE R...
  • Page 45 Inspect the squeegee blade. If the blade is worn, turn the blade so that a new edge is in the wiping position. Reinstall squeegee assembly on the machine. Note Toothed lock washers must be on top of support plate AMERICAN-LINCOLN 1-45 ENCORE R...
  • Page 46 Remove the cover from the solution tank, rotate the handle on the drain plug counterclockwise and then pull up as shown in figure 61. After the tank has drained, flush out with clean water and reinstall the plug. 1-46 AMERICAN-LINCOLN ENCORE R...
  • Page 47 PULL FORWARD TO TIGHTEN BELT TO ADJUST BELT SIDE BROOM BELT Fig. 64 Side Broom Belt 1. Check belt tension adjustment as shown in figure 64. 2. Loosen pulley and broom nut. 3. Force pulley and broom forward. 4. Retighten. AMERICAN-LINCOLN 1-47 ENCORE R...
  • Page 48 66. Check fuses with an amp meter to locate the blown fuse. Replace the fuse with one of exactly the same size as shown in figure 67 and 68. Replace the cover and tighten the internal hex screws. Fuse Part Nos. 2-00-05861 (2 amp) 2-00-05860 (10 amp) 8-28-05019 (70 amp) 1-48 AMERICAN-LINCOLN ENCORE R...
  • Page 49 Fuse 6 2 Amp Tank Float Switch Fuse Fuse 7 10 Amp Light and Horn Fuse Fuse 8 10 Amp Option Pump Fuse WARNING Replace fuses with the same size fuse to avoid damage to electrical components. AMERICAN-LINCOLN 1-49 ENCORE R...

  • Page 50: Troubleshooting

    3. Adjust or replace 4. Hopper not installed broom belts. Reset correctly. circuit breakers 5. Poor broom pattern. adjust broom micro 6. Flaps worn. switches. Repair loose wire connections. 4. Reinstall. 5. Adjust sweep pattern. 6. Repair or replace. 1-50 AMERICAN-LINCOLN ENCORE R...
  • Page 51 4. Remove obstruction, 4. Overload of drive put drive pedal in circuit. neutral. 5. Adjust. Machine does not move. 1. Blown fuse. 1. Check fuse and 2. Battery unplugged. replace if necessary. 2. Plug in battery. AMERICAN-LINCOLN 1-51 ENCORE R...

  • Page 52: Trouble Shooting

    4. Brushes rotating opposite direction 1. Lift actuator out of Squeegee leaves wet spots adjustment 2. Squeegee wheels out of adjustment Squeegee makes excessive 1. Blades worn or damaged noise 1-52 AMERICAN-LINCOLN ENCORE R...
  • Page 53 NOTES AMERICAN-LINCOLN 1-55 ENCORE R...
  • Page 54 Division of Nilfi sk-Advance A/S Industrivej 1 9560 Hadsund Denmark Tel.: (+45) 72 18 21 00 Fax: (+45) 72 18 21 11 E-mail: salg@nilfi sk-alto.dk E-mail: service@nilfi sk-alto.dk www.nilfi sk-alto.dk...

Table of Contents