Simple Setup; Step 1 Front And Surround Speaker Assembly - Panasonic SC-HT885W Operating Instructions Manual

Simple setup

1
STEP
Preparation
≥To prevent damage or scratches, lay down a soft cloth and perform assembly on it.
≥For assembly, use a Phillips-head screwdriver.
≥Make sure you have all the indicated components before starting assembly, setup, and connection.
≥There is no difference between the right and left speakers and pipes.
[Note]
≥To prevent the speaker cables from being pulled out of the pipes, leave the plastic wrap on the pipes while assembling the speaker stands.
≥[Continental[Europe\
The front and surround speaker pairs as well as the pipe pairs are different.
–Check the label on the rear of the speaker before attaching the pipe (➜ page 5).
–The pipe with the shorter cable is for the front speaker.
[Continental[Europe\
2 Front and
2 Surround speakers
[Southeast[Asia,]
[the[Middle[East,[South[Africa,[
[Saudi[Arabia[and[Kuwait[
4 Front/Surround
speakers
1
Assemble the speaker stands.
1
Thread the speaker cable through the base.
For quicker threading, loosely fold the cable in half (do not
crease), pass the folded portion through the hole, and then pull
the rest of the cable through the base.
Plastic wrap
Leave the excess speaker
cable for connecting later.
2
Insert the pipe.
Pipe
Groove
Pipe support
Base
3
Secure the pipe to the base.
Ensure the screws are securely fastened.
Short screws
Before proceeding to the next step, please remove the plastic
wrap from the pipe.
2
Attach the stands to the speakers.
Ensure the stand is fastened on straight by gradually tightening the
top and bottom screws alternately until fully tightened.
You can also attach to the lower rear of the speaker.
RQT8221
The height of the speaker can be changed when attaching the
4
stand to the upper rear or lower rear of the speaker.
Front and surround
speaker assembly
Pipes
≥2kpipes with short cable: For front speakers
≥2kpipes with long cable: For surround speakers
Cable
Base
Match the groove and these
holes with the base when you
insert the pipe.
Insert the pipe while gently
pulling on the speaker cable.
Phillips-head
screwdriver (not included)
Long screws
Pipe
Speaker
The supplied stands are specially designed for
attachment to Panasonic SB-FS930 front speakers,
SB-FS880 surround speakers, or SB-FS881 front or
surround speakers. Use only as indicated in this setup.
4 Bases
3
Connect the speaker cables.
Twist off the vinyl ends of the
§
speaker cables.
_:
Copper
`:
Silver
Push!
§
If the speaker cables do not have vinyl
tips, directly connect them to the
terminals.
Press the speaker cable into the
groove.
If there is any excess speaker cable, thread the speaker cable
into the opening near the top of the pipe while pulling the speaker
cable from the bottom of the base.
4
Secure the speaker cables to the bases.
Press the speaker cable into
the base cover groove as far
as possible.
Cable
∫ Preventing the speakers from falling over
Preparation
Attach screw eyes (not included) to secure the speakers to the wall
(➜ diagram below).
≥You will need to obtain the appropriate screw eyes to match the
walls or pillars to which they are going to be fastened.
≥Consult a qualified housing contractor concerning the
appropriate procedure when attaching to a concrete wall or a
surface that may not have strong enough support. Improper
attachment may result in damage to the wall or speakers.
1
Thread the string (not included) through the slot on the
rear of the speaker to prevent it from falling over.
2
Loop the string through the screw eye and tie tightly.
Screw eye (not included)
String (not included)
Rear of the speaker
8 Long 8 Short
screws screws
Rear of the speaker
Rear side
of base
Groove
Wall
Approx. 150 mm