Read Before Using - SPYKER 100 Operation Manual Service Manual Parts List

Model 100 Parts List
Item # Part # Quantity Description
1 05-98-0021-5 1 5' Extension Cable
2 05-98-0122 1 12 VDC, 550 RPM, 1/15 HP Motor
3 05-98-0128 1 Rubber Boot / Motor
4 05-94-0082 1 Cover / Hopper
5 05-99-0093 1 Manual
6 05-90-0044 1 Cable Fastener
7 05-94-0064 8 Nylon Washer / Hopper / Motor Mount
8 99-10-0205 11 Bolt, 1/4-20 X 1/2" Hex Head / Frame / Hopper Bottom Plate
9 05-90-0051 8 Bolt, 1/4-20 X 3/4" Truss Head / Hopper / Motor Mount
10 SS-91-0004 14 Nut, 1/4-20 Nylock
11 05-94-0042 2 Rate Gate / Accuway Guide
12 SS-94-0007 1 Hopper Bottom Bushing
13 05-94-0043 1 AccuwayTM
14 SS-96-0003 1 Agitator Wire
15 05-104-2245 1 Coupling / Spinner Shaft
16 05-90-0041 2 Set Screw, 1/4-20 Allen Head
17 05-100-0033 1 Spinner Shaft
18 05-97-0036 1 Spinner Clip
19 05-98-0061 1 Variable Speed Motor Control Unit, 12vdc
20 05-91-0023 1 Nut, Fine Thread Hex / On/Off Control Cable
21 05-92-0013 1 Washer, Tooth Lock, SS / On/Off Control Cable
22 05-100-2204 1 Motor Mount
23 05-71-2205 1 Hopper Bottom Plate
24 05-100-2208 1 Hopper
25 05-94-0068 1 Rate Gate
26 05-94-0069 1 Dial Mount
27 SS-94-0006 1 Dial
28 05-94-0078 1 Pine Tree Clip / Dial Assembly
29 05-24-1102 1 Rate Gate Linkage
30 05-94-0045 1 AccuwayTM Adjustment Screw
31 05-94-0046 1 AccuwayTM Adjustment Nut Bracket
32 05-100-2203 1 Frame Side R.H.
33 05-100-2202 1 Frame Side L.H.
34 05-100-2201 1 Frame Back
35 05-100-2205 2 Strut / ATV Mount
36 05-90-0083 4 U-Bolt, 5/16" X 1 3/8"W X 3 3/4"H / ATV Mount
37 05-90-0087 4 Bolt, 1/2-13 X 1 1/4" HH / ATV Mount
38 05-91-0030 4 Nut, 1/2-13 / ATV Mount
39 05-92-0003 4 Lockwasher, Split, 1/2" SS / ATV Mount
40 05-94-0050 2 Fire Ant Bait Plate
41 05-90-0055 5 Bolt, 10-32 X 1/2", HH, SS / Motor / Cable Retainer
42 05-88-2241 1 Cable Retainer
43 05-220-0140 1 Spinner
Optional Accessories
11-111-1111 Parts
6

Read Before Using

SPEED - ACCURACY - FREEDOM FROM STRIPES AND STREAKS
are yours - when you use this Spreader.
The spread width ranges from 4 ft. to 12 ft. wide, depending on the
volume/density, particle size of the material and the rate of travel.
The spread thins or feathers at the outer edges, eliminating sharp,
"Edge of spread" lines which cause stripes and streaks. Extra coverage
can be given under trees and other heavy feeding areas without
showing "edge of spread" lines.
Gaps and double overlaps are less likely. Small errors in travel are
forgiven and do not show.
WARNING: When spreading products containing herbicides, exercise extreme
caution with respect to careless spreading and to wind-drift.
CONTACT OF SOME PRODUCTS ON SOME PLANTS CAN BE FATAL.
If a dial setting is not found, use the size and weight comparison table
found on the back page.
Determine a dial setting on the low side. If the setting proves to be
too low, cover the area more than one time. A higher setting can be
used when a proven dial setting is established.
REMEMBER - Published dial settings can be approximate only. The
operation of the spreader, the condition of the material (damp or dry
or over-pulverized) and weather conditions, are all contributing factors.
For these reasons, it's often a good idea to spread the area 2 times -
at one-half rate - in cross directions (SEE INFORMATION ON ONE-HALF
RATE DIAL SETTINGS ON REFERENCE CHART ON THE BACK PAGE.
SPREADING AT ONE-HALF RATE DIAL SETTINGS IS HIGHLY
RECOMMENDED UNDER DAMP & HUMID CONDITIONS.
BECOME FAMILIAR WITH THE OPERATION OF THE SPREADER
BEFORE YOU PUT MATERIAL IN THE HOPPER.
Practice walking with the spreader, opening and closing the rate gate
at the appropriate times.
Travel at a constant speed and operate the spreader lever position.
Remember: Open the rate gate after the spreader is in motion at
operating speed (about 3 mph.).
Close the rate gate while spreader is still at operational speed.
7