Table of Contents
Advertisement
Model 80 Parts List
Item #
Part #
Quantity
Description
1
05-98-0104
1
On/Off Control Lever
2
05-95-0046
2
Idle / Drive Wheel
3
05-94-0042
2
Rate Gate Guide
4
05-94-0064
4
Nylon Washer / Hopper
5
SS-94-0007
1
Hopper Bottom Bearing
6
05-94-0043
1
AccuwayTM
7
SS-94-0011
2
Axle Bushing
8
SS-96-0003
1
Agitator Wire
9
99-10-0205
5
Bolt 1/4-20 x 1/2" / Hopper Bottom Plate
10
05-90-0098
2
Jay Bolt / Handle
11
05-98-0089
2
Plastic Knob / Handle / Jay Bolt
12
05-94-0103
2
Plastic Plug / Hopper Support Tube End
13
05-90-0054
8
Bolt 1/4-20 x 1 1/2" / Hopper / Frame Braces
14
SS-91-0004
10
Lock Nut 1/4-20 / Hopper / Frame / Frame Braces
15
05-90-0038
2
Bolt 1/4-20 x 2" / Frame
16
05-90-0042
2
Bolt 10-24 x 1 1/4" / On/Off Lever
17
05-91-0008
2
Lock Nut 10-24 / On/Off Lever
18
05-90-0065
1
Clevis Pin 3/16" x 1 3/4" / Drive Wheel
19
05-90-0089
1
Hair Pin / Drive Pin
20
05-90-0055
1
Bolt 10-32 x 1/2" SS HH / Cable Retainer
21
SS-92-0002
2
Felt Washer / Gear Box / Hopper
22
05-94-0102
1
Handle Grip
23
05-98-0120
2
Collar 1/2" / Axle
24
05-80-2202
2
Axle Support Tube
25
05-71-2205
1
Hopper Bottom Plate
26
05-88-2241
1
Cable Retainer / Cable Mount Bracket
27
05-35-2203
1
Ground Prop / Hopper Support
28
SS-90-0001
2
Roll Pin, .125 x 3/4" / Bevel Gear / Pinion Gear
29
SS-90-0002
2
Roll Pin, 1/8" x 7/8" / Bevel Gear / Pinion Gear
30
SS-94-0010
1
Bevel Gear
31
SS-94-0009
1
Pinion Gear
32
SS-94-0012
1
Spinner
33
05-94-0029
1
Bushing / Gear Box
34
SS-94-0014
4
Clamp Ring / Gear Box
35
SS-94-0008
2
Gear Box Half
36
05-35-0060
1
Spinner Shaft
37
05-35-0050
1
Axle
38
05-80-0030
1
Hopper
39
05-94-0068
1
Rate Gate
40
05-94-0069
1
Dial Mount
41
SS-94-0006
1
Dial
42
05-90-0044
1
Cable / Wire Fastener
43
05-94-0078
1
Pine Tree Clip / Dial Mount
44
05-24-1102
1
Rate Gate Linkage
45
05-35-2204
1
Handle
46
05-94-0045
1
AccuwayTM Adjustment Screw
47
05-94-0046
1
AccuwayTM Nut / Bracket
48
05-35-0280
1
Cable Mount Bracket
49
05-35-1040
2
Frame Brace
Optional Accessories
11-111-1111
Parts
6
Read Before Using
SPEED - ACCURACY - FREEDOM FROM STRIPES AND STREAKS
are yours - when you use this Spreader.
The spread width ranges from 4 ft. to 12 ft. wide, depending on the
volume/density, particle size of the material and the rate of travel.
The spread thins or feathers at the outer edges, eliminating sharp,
"Edge of spread" lines which cause stripes and streaks. Extra coverage
can be given under trees and other heavy feeding areas without
showing "edge of spread" lines.
Gaps and double overlaps are less likely. Small errors in travel are
forgiven and do not show.
WARNING: When spreading products containing herbicides, exercise extreme
caution with respect to careless spreading and to wind-drift.
CONTACT OF SOME PRODUCTS ON SOME PLANTS CAN BE FATAL.
If a dial setting is not found, use the size and weight comparison table
found on the back page.
Determine a dial setting on the low side. If the setting proves to be
too low, cover the area more than one time. A higher setting can be
used when a proven dial setting is established.
REMEMBER - Published dial settings can be approximate only. The
operation of the spreader, the condition of the material (damp or dry
or over-pulverized) and weather conditions, are all contributing factors.
For these reasons, it's often a good idea to spread the area 2 times -
at one-half rate - in cross directions (SEE INFORMATION ON ONE-HALF
RATE DIAL SETTINGS ON REFERENCE CHART ON THE BACK PAGE.
SPREADING AT ONE-HALF RATE DIAL SETTINGS IS HIGHLY
RECOMMENDED UNDER DAMP & HUMID CONDITIONS.
BECOME FAMILIAR WITH THE OPERATION OF THE SPREADER
BEFORE YOU PUT MATERIAL IN THE HOPPER.
Practice walking with the spreader, opening and closing the rate gate
at the appropriate times.
Travel at a constant speed and operate the spreader lever position.
Remember: Open the rate gate after the spreader is in motion at
operating speed (about 3 mph.).
Close the rate gate while spreader is still at operational speed.
7
Advertisement
Table of Contents
