Adding New Sound On A Recorded Cassette - Panasonic NV-MX1B Operating Instructions Manual

VIDEO CAMERA
START/
DATE/ PHOTO
STOP
OSD
TIME SHOT
COUNTER RESET TITLE
ZOOM
T
MULTI
REC A.DUB
¥
P-IN-P
V /REW PLAY FF/ W
W
6 1 5
STILL ADV PAUSE STILL ADV
E ; D
INDEX STOP INDEX
: 9
∫
SELECT
VAR. P.B.
SEARCH ZOOM
STORE
MENU
SET
OFF/ON
ITEM
P.B.DIGITAL
Title
Adding New Sound on a
Recorded Cassette
(Audio Dubbing)
You can add music or narration on a recorded
cassette.
≥If you perform audio dubbing onto a tape that was
recorded with [AUDIO REC] on the [RECORDING
SETUP] Sub-Menu of the [CAMERA FUNCTIONS]
Main-Menu set to [16bit], the original sound is
erased.
If you intend to perform audio dubbing but also want
to keep the original sound, be sure to set [AUDIO
REC] to [12bit] before making the original recording.
≥It is not possible to perform audio dubbing onto
recordings made in the LP Mode. (p. 13)
≥Audio dubbing using the [AV IN/OUT] socket is
possible only with the NV-MX7 model. Step 2 and 3
need not be performed for all other models.
60
CAMERA
VCR
CARD P.B
MODE
ON
OFF
MENU
2 1 PUSH W.B/SHUTTER/IRIS/VOL/JOG
Procedure
1 2
Insert the recorded Set [AV JACK] on the
cassette and slide the [AV IN/OUT SETUP]
[OFF/ON/MODE] Switch Sub-Menu to [IN/OUT].
from the [ON] position to
put the Movie Camera in
the VCR Mode.
≥Make sure that the
prevention slider of the
cassette is set to [REC].
CAMERA MENU
VCR
CARD P.B
2 1
MODE
ON
OFF
4 5
At the point from which Press the [A.DUB]
you want to insert the Button on the Remote
new sound, switch the Controller.
Movie Camera over to
the Still Playback Mode.
A.DUB
PLAY
1
PAUSE
;
A.DUB;
3
Set [A. DUB INPUT] on
the [AV IN/OUT SETUP]
Sub-Menu to [MIC] or
[AV IN], and exit from
the Menu.
[AV IN]:
For performing audio
dubbing using an
MENU
external device (such as
an audio component).
[MIC]:
2 1
For performing audio
dubbing using the
external microphone
socket or built-in
microphone.
6
Stopping Audio
Dubbing
Press the Pause Button
Press the Pause Button
[;] on the Remote
[;] on the Remote
Controller.
Controller to start
The Movie Camera is
audio dubbing.
again in the Still
≥In the case of line input
Playback Mode.
signals, play the device
which has been
connected.
PAUSE
PAUSE
;
;
A.DUB!
Remarks, etc.
≥It is not possible to perform audio dubbing on an
unrecorded part of the tape.
≥If there was an unrecorded part on the tape when
audio dubbing was performed, picture and sound
distortion occur at that tape portion during
playback.
≥It is not possible to perform audio dubbing for sound
supplied from the DV Terminal.
≥If you reset the Tape Counter to zero at the point
where you want the audio dubbing to end and turn on
the Memory Stop Function (p. 121), the audio
dubbing automatically stops when the tape reaches
that point.
≥If the data recorded with audio dubbing is imported in
the personal computer using a PC software
programme, only the original sound (ST1) may be
imported depending on the software programme.
Playing Back the Sound Recorded with Audio
Dubbing
≥Depending on the setting selected for [12bit AUDIO]
on the [PLAYBACK FUNCTIONS] Sub-Menu of the
[VCR FUNCTIONS] Main-Menu, the sound added
with audio dubbing and the original sound are played
back as follows:
ST1: The original sound alone is played back.
ST2: The dubbed sound alone is played back.
MIX: The original sound and the sound added with
audio dubbing are played back together.
61