Using The Wired Remote Control; Using The Unit With Optional Accessories; Maintenance; Using The Unit With An Audio System - Panasonic SL-CT570 Operating Instructions Manual

Using the Wired Remote Control

The remote control can be operated regardless of the hold mode
of the unit.
Preparation:
Release the remote control from the hold mode.
VOLUME
HOLD
∫ Operation confirmation tones
When an operation button is pressed, a confirmation tone
sounds. Refer to the parentheses in the illustration for the differ-
ent types of confirmation tones.

Using the Unit with Optional Accessories

A
[OUT] jack
Side panel of the unit
Stereo phono
cable (not included)
(White)
(Red)
B
[OPT OUT] jack
Side panel of the unit
o
Optical cable
(not included)
To optical in jack
5
How to use the wired remote control
2
HOLD
To start play
To stop play
To turn off the

Using the unit with an audio system

Stereo connection A
Use a stereo connection cable (not included) to listen to CDs
through your home audio system.
≥Turn off the amplifier before connecting the cable.
≥Do not connect the cable to the PHONO jacks on the amplifier.
≥Obtain the optional connecting cable if the amplifier comes with
Amplifier
mini-phone jacks.
L ≥Adjust the volume level on the amplifier.
To CD or AUX
Note.
terminals
≥Sound quality changes when S-XBS, TRAIN or LIVE is select-
R
ed, but volume is reduced by approximately fifty percent.
≥Set anti-shock to the 10-second mode or turn it off for purer
sound. The 40-second mode digitally compresses the audio sig-
nal.
≥You can connect speakers, active or otherwise, with an imped-
ance of 1 k≠ or less to the headphone jacks. Set the unit's vol-
ume between 4 and 6.
Digital connection B
Use a optical cable (not included) to connect to digital recording
equipment, such as a mini-disc deck.
≥Turn off the mini-disc deck before connecting the cable.
≥Use the AC adaptor to power this unit.
≥Turn the anti-shock function off.
Mini-disc deck
Note.
≥Sound quality is unchanged when S-XBS, TRAIN or LIVE is se-
lected.
≥This connection can not be used if the unit is powered with bat-
teries.
Press once during off or stop mode.
Press once during play.
Press and hold during play or stop
mode.
unit
(Beep...Bee...p)
Skipping
tracks
PUSH
(Beep)
Searching
through tracks
PUSH
(Beep...Beep)
To adjust the
volume
PUSH
Using the unit with a car audio
system
Items to be purchased
For connection to the car audio system:
Car stereo cassette adaptor (SH-CDM10A)
Connect the car stereo cassette adaptor to the unit's
headphone jack. (When doing this, keep the unit's
VOLUME at a setting between 4 and 6.)
For securing the unit and connecting the power
supply:
≥Car adaptor (SH-CDC9)
≥Car mounting kit (SH-CDF7)
Note.
It may not be possible to use the unit with some types of car
stereo owing to restrictions imposed by the construction of the
car stereo cassette adaptor.
For further details, refer to the instructions of the part concerned.

Maintenance

If the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
If the surfaces are extremely dirty, use a soft cloth dipped in a
soap-and-water solution or a weak detergent solution.
≥Never use alcohol, paint thinner or benzine to clean this unit.
≥Before using chemically treated cloth, read the instructions that
came with the cloth carefully.
Maintaining the lens
Open the lid and clean the lens as shown in the figure.
Use a cotton swab to gently wipe off any finger-prints.
Recommended product: Lens cleaner kit (SZZP1038C)
Air blower for
camera lens
Lens
Turn during play
Backward Forward
(Beep Beep Beep) (Beep Beep)
Turn and hold during play.
When adjusting the volume using the
remote control, position the volume
control on the unit between 4 and 6.
s r
VOLUME
2
HOLD
Lens