Page 1
ORDER No. AD9912264C3 Portable CD Player SL-CT570 Traverse Deck: RAE0220Z Mechanism Series Colours (S)....Silver Type (A)....Blue Type Areas GK...China. GH...Hong Kong.
SPECIFICATIONS Specification Audio (Anti-shock off) No. of channels: 2 channels (left and right, stereo) Frequency response: 20 to 20,000 Hz (+0.5dB, - 1.5dB) Output voltage: 0.6 V (50k S/N: more than 96 dB Wow and flutter: Below measurable limit DA converter: 1 bit, MASH Headphones output level: Max.
[When used in hold mode, at 25°C (77°F) temperature and on flat and stable surface] Batteries used ANTI-SHOCK MEMORY II OFF/ ON 2 ”AA” (LR6) alkaline batteries About 24h/ 30h 2 “AAA” (LR03) alkaline About 10h/ 13h batteries Ni-MH Rechargeable batteries About 6h/ 8h 4 alkaline batteries About 38h/ 50h...
Page 4
Wave length: 780nm Maximum output radiation power from pickup: 100 W/VDE Laser radiation from the pickup lens is safety level, but be sure the followings: 1. Do not disassemble the optical pickup unit, since radiation from exposed laser diode is dangerous. 2.
Page 6
4.2. Grounding for electrostatic breakdown prevention 1. Human body grounding Use the anti-static wrist strap to discharge the static electricity from your body. (as shown in Fig.2 2. Work table grounding Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed, and fround the sheet.
6. Checking the Operation Problems on the Traverse Deck (Optical Pickup) Make sure to follow the procedures below to check the operation problems of the traverse deck (optical pickup) before replacing it. Replace the traverse deck only after the problem is identified.
Page 13
Check the operations described below on the traverse deck after replacing it. *Checking Skip Search 1. Play an ordinary musical program disc. 2. Press the skip button to check for normal skip search operation (in both the forward and reverse directions). *Checking Manual Search 1.
7. Automatic Adjustment Results Display Function (Self-check Function) On this unit (SL-CT570), each automatic adjustment results are displayed on the LCD. This function is convenient to check or identify which automatic adjustment circuit is incorrect. The followings are the contents of the automaticadjustment result displays (self-check function).
<Example> Follow the below steps when “E-1” is displayed. (Cause: Focus balance (FBC) is set beyond the limit.) Check if (1) the waveform or voltage of the focus servo circuit is correct. (check the waveform or voltage.) (2) the optical pickup returns to the normal state by exchanging the traverse deck. Follow the below steps when “E-4”...
Page 16
- DC voltmeter - Lead wire (for test points) Test short land Short-circuit the lands of the laser ON/OFF swtch (S201) by soldering them. It turns “ON” position. (Refer to below or “12. Printed Circuit Board and Wiring Connection Diagram” for shortland location) Note: Remove the solders from the short lands after adjustment.
Page 17
1. Connect the DC voltmeter to VDD(+) and GND on the P.C.B.. 2. Connect the AC adaptor cord to the DC IN port (or use the full- recharged rechargeable battery, a new article batteries) and load the test disc (SZZP1054C). 3.
9.1. Conventional Shockproofing Technique (LCD Display: Input information read out of the CD at double speed is demodulated, stored in the memory, and while sound-marking signal is supplied at normal speed from the memory to the D/A converter, the residual data is accumulated in the memory. If reaccess to the break point is accomplished before the memory becomes empty, apparent playback sound is entirely kept free from breaking even when information pauses due to vibration, etc.
Page 20
- Ground the soldering iron. - Put a conductive mat on the work table. - Do not touch the pins of IC or LSI with fingers directly. 11. Schematic Diagram 12. Printed Circuit Board and Wiring Connection Diagram 13. Block Diagram 14.
Page 21
Mark I/O / Function Division PDOWN Reduced voltage detection signal output terminal OFTR Off-track signal output terminal (H: off-track) — Not used, open RF envelop signal output terminal Envelop control input terminal — Not used, open TE IN Tracking error amplifier input terminal TE OUT Tracking error amplifier...
Page 22
Mark I/O / Function Division 3KEY A/D key input terminal (Not used, open) Doctor mode input terminal DOCTOR (Connected to power supply though resistor) — Not used, open STOP STOP key input terminal SKIP.F SKIP.F key input terminal SKIP.R SKIP.R key input terminal REPEAT REPEAT key input terminal 8 MEMORY...
Page 23
Mark I/O / Function Division 24 ZANSEL For selection of battery remaining power indication input terminal /RESET Reset detection input terminal BATT Output terminal for STROBE measurement of battery charging voltage (Measured by Hi-Z) OPEN Cover open detection input terminal XOSCIN Clock signal input terminal when MSEL is H: Crystal...
Page 24
Mark I/O / Function Division Spindle moter gain control signal output terminal JUG GL — Not used, open Not used, open — 47 REMSEL LCD remote control (3 key wireless) switching input terminal (Connected to power supply) 48 RAMSEL — For selection of 4M/16M DRAM input terminal (Not used, open)
Page 25
Mark I/O / Function Division — Triangular wave output terminal (Connected to GND through capacitor) Power supply input terminal Not used, open — VREF Reference voltage input terminal External clock input terminal PVCC1 Power supply input terminal VO1R Focus coil drive signal output terminal PGND1 —...
Page 26
Mark I/O / Function Division VO3R Traverse motor drive signal output terminal PVCC3 Power supply input terminal VO3F Traverse motot drive signal output terminal Connected to GND 31 PGND34 — Not used, open — Power supply output terminal for spindle motor drive PVCC4 Power supply input terminal...
Page 27
Mark I/O / Function Division UOUT Spindle motor drive signal output terminal — Output current detection terminal (Connected to GND through resistor) Motor position detection input terminal Motor coil midpoint input terminal — Starting oscillation capacitor / connection terminal (Connected to GND through capacitor) CSL1 —...
Page 28
Mark I/O / Function Division Connected to GND PGND1 — DC/DC converter coil drive terminal PVCC1 Power supply input terminal VSEN Empty detection input terminal (Connected to power supply) 5 RESTART DC/DC converter drive input terminal (Connected to power supply through capacitor) ICNT Setting of charging current...
Page 29
Mark I/O / Function Division DC/DC converter external clock input terminal Connected to GND 22 PREGND — AREF Audio reference output terminal AVCC Ripple filter output terminal (Connected to power supply) Ripple filter smoothing capacitor connection terminal (Connected to GND through capacitor) RESET Reset detection output...
Page 30
Processing, Digital Filter, and D/A Converter Mark I/O / Function Division DVDD3V Power supply input terminal for DRAM Data input/output terminal for DRAM Write enable output terminal for DRAM NRAS RAS control signal output terminal for DRAM Data 2/3 input/output terminal for DRAM NCAS0 CAS control 0 signal output...
Page 31
Mark I/O / Function Division CSEL Frequency control input terminal of crystal osicillator (Not used, connected to GND) Focus error signal input terminal (Analog input) Tracking error signal input terminal (Analog input) RFENV RF envelope signal input terminal (Analog input) Off-track signal input terminal (H: off-track) 36 NRFDET...
Page 32
Mark I/O / Function Division — TMOD1 Terminal mode switching input 1 terminal (L: normal) (Connected to GND) — TMOD2 Terminal mode switching input 2 terminal (L: normal) (Connected to GND) FLAG — Flag signal output terminal (Not used, open) FCLK —...
Page 44
:CD PLAYBACK SIGNAL LINE :POSITIVE VOLTAGE LINE Q201 2SB709ATX LASER POWER DRIVE R201 SHORT LAND (1.9V) 2.5V OPTICAL PICKUP (2.2V) S201 (LASER ON/OFF) 0.047 0.22 CN101 RF( A) R113 TE(F) TE(E) R114 VREF RF( B) TRACKING COIL FOCUS COIL PLAY 70mV 2ms.
Page 45
:POSITIVE VOLTAGE LINE OPERATION/LCD UNIT LCD301(RSL5248 C) LCD DISPLAY 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CN301 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b d...
Page 46
:POSITIVE VOLTAGE LINE S202 TRAVERSE SPINDLE (REST DET. MOTOR MOTOR SWITCH) CN401 2.5V 3.2V R435 Q431 C438 R441 DTA144EUA106 1500P 180K SWITCHING (3.2V) IC402 3.2V BA6966FVE2 MOTOR DRIVE 2.5V (0V) IC401 BH6522FVE2 COIL & MOTOR DRIVE IN2F (0V) 2.5V MUTE (PC) IN2R 7.1V IN1R...
Page 47
:POSITIVE VOLTAGE LINE :CD PLAYBACK SIGNAL LINE 2.8V 2.5V 3.2V RJ508 (0.6V) (0.5V) (0.2V) (0.2V) (0.6V) (1.5V) (1.5V) 2.5V 2.5V 2.5V 0.7V 0.7V 2.5V IC502 M51V7400D1FS 16M DRAM 2.5V 0.4V 0.4V (0.5V) (0.6V) (0.6V) (0.5V) (0.5V) (0.5V) (1.5V) (1.5V) B C D E F G H I J K L M N O P C502 2.4V...
Page 48
:CD PLAYBACK SIGNAL LINE :POSITIVE VOLTAGE LINE 2.8V 2.5V 3.2V POWER SUPPLY IC11 VOLTAGE ADJ. RS10003E2 DC DC CONVERTER MA741WKTX 1.2V PREGND 1.5V 2.5V MCLK/ AREF CHARGE 2.5V MLD/ VCNT 2.5V 6.3V22 MDATA/ 2.8V 2.5V MSTAT/ RESET ACDET 6.1V 120P 1.6V 2.4V 2.4V...
Page 49
:CD PLAYBACK SIGNAL LINE :POSITIVE VOLTAGE LINE 2.8V JK11 DC IN 4.5V Q904 R902 2.5V 270K 2SD1819ATX 1.1V ICP11 SWITCHING UNHH20600L (REMOTE) 2.5V CN11 2 R03/LR03(UM-4) BATTERIES . . . 3V (0V) (2.8V) 2 RECHARGEABLE 2.5V BATTERIES . . . 2.4V (2.8V) 2.2V (2.8V)
ELECTRICAL PARTS LOCATION (SIDE:B) Ref. Ref. Ref. Ref. Note: This printed circuit board diagram may be modified at any time with the development of new technology. (SIDE:A) IC11 CN51 R511 C201 IC401 CN101 R604 C302 IC502 CN301 R605 C401 IC701 CN401 R607 C402...
Portable CD player A Skip/search buttons (:, 9 6, 5) B Memory/recall button (MEMORY/RECALL) C EQ button (EQ) D Display E Battery check button (BATT CHECK) F Play/pause button (1 ;) G Stop/operation off button (∫, OPR OFF) H Repeat button (`) I Anti-shock button (A.SHOCK) J Out jack (OUT) K Optical digital out jack (OPT OUT)
Page 58
ELECTRICAL PARTS LOCATION (SIDE:B) Ref. Ref. Ref. Ref. Note: This printed circuit board diagram may be modified at any time with the development of new technology. (SIDE:A) IC11 CN51 R511 C201 IC401 CN101 R604 C302 IC502 CN301 R605 C401 IC701 CN401 R607 C402...
Page 59
AN8839NSBE1 IC101 OPTICAL PICKUP SERVO AMP RF IN CS BRT Semiconductor RFENV OFTR 3 TENV laser DET. Vref. OFTR OFTR Q201 Vref. Laser BDO DET. power cont. /RFDET NRFDET DET. Vref. FE IN SUBTRA- CTOR FE OUT Vref. Vref. VCBA Vref.
Page 60
MN662784SA IC501 SERVO PROCESSOR / DIGITAL SIGNAL PROCESSOR DIGITAL FILTER & D/A CONVERTER +B5 +B3 DIGITAL AUDIO INTERFACE DSL/PLL VCO DEMODULATION/ SYNC INTERPOLATION/ OUTR SUBCODE L.P.F. SQCK 4TIMES DEMODULATION 1 BIT SUBCODE OVER SAMPLING/ BUFFER DIGITAL FILTER/ SUBQ SOFT MUTING/ LOGIC DIGITAL OUTL...
Page 63
Portable CD player A Skip/search buttons (:, 9 6, 5) B Memory/recall button (MEMORY/RECALL) C EQ button (EQ) D Display E Battery check button (BATT CHECK) F Play/pause button (1 ;) G Stop/operation off button (∫, OPR OFF) H Repeat button (`) I Anti-shock button (A.SHOCK) J Out jack (OUT) K Optical digital out jack (OPT OUT)
Page 65
:CD PLAYBACK SIGNAL LINE :POSITIVE VOLTAGE LINE Q201 2SB709ATX LASER POWER DRIVE R201 SHORT LAND (1.9V) 2.5V OPTICAL PICKUP (2.2V) S201 (LASER ON/OFF) 0.047 0.22 CN101 RF( A) R113 TE(F) TE(E) R114 VREF RF( B) TRACKING COIL FOCUS COIL PLAY 70mV 2ms.
Page 66
:POSITIVE VOLTAGE LINE OPERATION/LCD UNIT LCD301(RSL5248 C) LCD DISPLAY 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CN301 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b d...
Page 67
:POSITIVE VOLTAGE LINE S202 TRAVERSE SPINDLE (REST DET. MOTOR MOTOR SWITCH) CN401 2.5V 3.2V R435 Q431 C438 R441 DTA144EUA106 1500P 180K SWITCHING (3.2V) IC402 3.2V BA6966FVE2 MOTOR DRIVE 2.5V (0V) IC401 BH6522FVE2 COIL & MOTOR DRIVE IN2F (0V) 2.5V MUTE (PC) IN2R 7.1V IN1R...
Page 68
:POSITIVE VOLTAGE LINE :CD PLAYBACK SIGNAL LINE 2.8V 2.5V 3.2V RJ508 (0.6V) (0.5V) (0.2V) (0.2V) (0.6V) (1.5V) (1.5V) 2.5V 2.5V 2.5V 0.7V 0.7V 2.5V IC502 M51V7400D1FS 16M DRAM 2.5V 0.4V 0.4V (0.5V) (0.6V) (0.6V) (0.5V) (0.5V) (0.5V) (1.5V) (1.5V) B C D E F G H I J K L M N O P C502 2.4V...
Page 69
:CD PLAYBACK SIGNAL LINE :POSITIVE VOLTAGE LINE 2.8V 2.5V 3.2V POWER SUPPLY IC11 VOLTAGE ADJ. RS10003E2 DC DC CONVERTER MA741WKTX 1.2V PREGND 1.5V 2.5V MCLK/ AREF CHARGE 2.5V MLD/ VCNT 2.5V 6.3V22 MDATA/ 2.8V 2.5V MSTAT/ RESET ACDET 6.1V 120P 1.6V 2.4V 2.4V...
Page 70
:CD PLAYBACK SIGNAL LINE :POSITIVE VOLTAGE LINE 2.8V JK11 DC IN 4.5V Q904 R902 2.5V 270K 2SD1819ATX 1.1V ICP11 SWITCHING UNHH20600L (REMOTE) 2.5V CN11 2 R03/LR03(UM-4) BATTERIES . . . 3V (0V) (2.8V) 2 RECHARGEABLE 2.5V BATTERIES . . . 2.4V (2.8V) 2.2V (2.8V)