Table of Contents
Advertisement
Power save:
To reduce the VCR's power consumption
when the VCR is switched off.
• Set Power save mode as follows:
[ON]:
The power consumption is greatly reduced when
the VCR is turned off.
[OFF]:
The power consumption is not reduced when the
VCR is turned off.
Refer to the followings when [Power save] is set to [ON].
• [VCR display] is automatically set to [OFF].
• To turn the VCR on, keep the [VCR-ON/OFF]
VCR main unit. It is not possible to turn it on with the remote
control.
• The Power save function does not work in the timer recording
standby mode. After all programmed timer recordings have been
made, and after all programmed data have been erased, the VCR
switches over to the Power save mode.
• When the VCR is off, Pay TV programmes cannot be watched on
the TV because the signal from the connected decoder is not
looped through. To watch them, turn on the VCR.
(For NV-FJ732EE and NV-FJ632EE)
VCR display:
For automatic change of the brightness of
the VCR display when the VCR is switched
off.
• Set the brightness of the VCR display as follows:
[ON]:
Indications are brightly lit.
[OFF]:
Indications are not lit.
[DIMMED]:
Indications are dimly lit.
OSD:
For automatic display on the TV screen of
the TV station information, type of sound
system of the programme being watched
and the sound playback mode.
(See page 21.)
• Set OSD mode as follows:
[4:3]:
Indications can be displayed on the TV screen.
[16:9]:
Indications can be displayed on the TV screen
when using wide type of TV screen and selecting
the wide screen mode on the TV setting.
• Even if setting to [16:9], indications may be cut off depending on
the TV.
[OFF]:
No indications appears.
AV2:
To select the type of external source
equipment which is connected to the VCR's
AV2 21-pin socket. (For NV-FJ732EE and
NV-FJ632EE)
• Set the external source equipment as follows:
[DECODER]:
When a decoder is connected.
[EXT LINK 1]:
When a digital receiver which transmits a special
control signal recordings via the 21-pin Scart
cable, for example the F.U.N. receiver
(TU-DSF30/S3) is connected for the linked timer
recordings. (See page 12.)
[EXT LINK 2]:
When an external equipment with a timer function
is connected for the linked timer recordings.
(See page 12.)
[EXT]:
When another VCR or a satellite receiver is
connected.
AV:
To select the type of external source
equipment which is connected to the VCR's
AV1 21-pin socket. (For NV-FJ628EE)
• Set the external source equipment as follows:
[TV/EXT]:
When TV, another VCR or a satellite receiver is
connected.
[EXT LINK 1]:
When a digital receiver which transmits a special
control signal recordings via the 21-pin Scart
cable, for example the F.U.N. receiver
(TU-DSF30/S3) is connected for the linked timer
recordings. (See page 12.)
[EXT LINK 2]:
When an external equipment with a timer function
is connected for the linked timer recordings.
(See page 12.)
20
TV system:
• Set the colour TV system as follows:
[AUTO]:
[PAL]:
[MESECAM]:
RFC system:
(1)
pressed on the
• Set the type of RFC system as follows:
[BG]:
[DK]:
[I]:
Remote:
• Set the Remote control mode as follows:
[VCR 1]:
[VCR 2]:
• To change the remote control mode on the remote control itself,
change the position of the [VCR 1/2] (16) to match the setting. If
these settings are not matched, the remote control cannot be used
to operate the VCR.
4) Press the [OK] (24) to conclude the setting.
5) Press the [EXIT] (27) to exit the On Screen Display.
Language or Country Setting
1) Press the [MENU] (7) to display the Main menu on the
2) Press the [Cursor] (38) 34 to
3) Press the [Cursor] (38) 3421
4) Press the [Cursor] (38) 34 to select the desired
5) Press the [OK] (24) to conclude the setting.
6) Press the [EXIT] (27) to exit the On Screen Display.
To select the type of colour TV system to be
used during playback or during recording
from an external source.
Normally set to this position.
When PAL system is used.
When SECAM system is used.
To set RFC system the same as the TV
system of the connected TV.
PAL B.G.H/SECAM B.G
PAL D/SECAM D.K. K1
PAL I
To set the Remote control mode.
(For NV-FJ732EE)
Select this setting on both the VCR and the
remote control for normal use with one VCR.
Select this setting on both the VCR and the
remote control when using this VCR and another
Panasonic VCR in the same place. This ensures
that you can operate both VCRs independently
with their respective remote control. It also allows
you to operate both VCRs with a single remote
control, simply by changing the remote control
mode on the remote control.
(Press it twice on the Remote control setting.)
TV screen.
select [Other settings]. Press the
[OK] (24) to display Other
settings menu.
to select [Language] or [Country]
and the entry field for [Language] or [Country] in this
order.
language or country.
Panasonic VCR
Other settings
2/2
TV system
: AUTO
RFC system
: DK
Remote
: VCR 1
Language
: English
Country
: others
Hide quick links:
Advertisement
Table of Contents
