Download Print this page

KitchenAid Pro Line Installation Instructions

Washer
Hide thumbs

Advertisement

Quick Links

Kit©he A|d
° PROLJ ®
EZ iNSTALLTips
Consultthe Useand CareGuideformoredetailedinstructions.
Move the washer into place and remove transport system.
Position the back of the washer
within 3 ft (91.4 cm) of its final
location.
NOTE: Door must be taped in
place prior to moving the
washer.
On the back of the washer
loosen the 4 transport
bolts
using a 13 mm wrench.
Pull out and discard transport
bolts and plastic spacers.
Pull the power cord through the
Cover the 4 bolt holes with the
opening and close the hole with
transport bolt hole plugs.
the attached cap.
Attach the door handle.
Connect inlet hoses to water faucets.
iMPORTANT: Check that there is a rubber washer in
each end of the hoses.
Insert the 2 screws through
the holes in the door. Place
the plastic washers onto the
screws. Attach the handle by
hand tightening the screws,
first the top then the bottom.
Push the handle against the
door. Using a Phillips
screwdriver, tighten the
screws.
NOTE: Do not overtighten.
Hand tighten couplings to
faucets.
2
Turn another Y_rotation.
Do not overtighten.
Run water into bucket to
determine which hose is hot and
which is cold.
installed Washer
iii_i
Connect inlet hoses to washer.
2
Hand tighten couplings - hot to
Turn another X_ rotation.
hot, cold to cold.
Do not overtighten.
Turn on the water faucets.
Check for leaks.
Secure the drain hose with the cable tie, in one of these ways:
laundry tub,
drainpipe (must be at least
39"[99 cm] high),
wall-mounted
standpipe.
Move washer to its final location and level the washer.
iMPORTANT:
Make firm contact with the floor and level
washer to maintain balance and minimize noise and vibration.
NOTE: Adjust the right front foot only. The other three feet
have been preset at the factory.
Push on the upper front panel to
be sure that the washer is on the
rear feet. Lower right front foot to
floor. By hand, firmly rotate foot
up to an additional 1_ turns.
Check the levelness of the washer,
side to side and front to back.
Rock washer gently front to back,
If level, use a gA_"(14 mm)
side to side and diagonally to make
open-end wrench to turn the
sure that all four feet are in firm
nuts on the feet tightly against
contact with the floor,
the washer cabinet.
NOTE: If the washer is not level, refer to the Use and Care Guide for
more detailed information.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow
these instructions can result in death, fire, or
electrical shock.
Plug into a grounded 3 prong outlet.
Check for leaks around faucets,
inlet hoses and drain hose.
French on back.
Version en fran£ais au verso.
3957667
4/06
@2006 All rights reserved.
¢3 Registered
trademark/TM
Trademark
of KitchenAid,
U.S.A., KitchenAid
Canada
Jicensee in Canada
Printed in U.S.A.

Advertisement

loading

  Also See for KitchenAid Pro Line

  Summary of Contents for KitchenAid Pro Line

  • Page 1 Version en fran£ais au verso. laundry tub, drainpipe (must be at least wall-mounted standpipe. 39"[99 cm] high), 3957667 4/06 @2006 All rights reserved. ¢3 Registered trademark/TM Trademark of KitchenAid, U.S.A., KitchenAid Canada Jicensee in Canada Printed in U.S.A.
  • Page 2 I'egout (doit 8tre tuyau de rejet A 1'6gout mural. A 39" [99 crn] de hauteur minimum), 3957667 4/06 TOUS droits rSserves. ® Marque deposee / TM Marque de commerce de KitchenAid U.S.A. Ernploi Iicenci_ par KitchenAid Canada au Canada Imprim_ aux E.=U.