Table of Contents
Advertisement
Available languages
Available languages
INSTALLATION REQUIREMENTS
•
Island trim and attachment
screws (3).
_-_ ,
-_
_ _ _ _i_4.
C
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
Tools needed
NOTE: The island trim included with the range may be used if
installed with 1" (2.5 cm) clearance from a combustible rear
wall or with 0" (0 cm) clearance from a noncombustible
rear
wall.
•
LP conversion kit.
•
Tape measure
•
1%e"combination
wrench
•
Flat-blade screwdriver
•
Marker or pencil
•
Phillips screwdriver
•
Masking tape
•
Level
•
Pipe-joint compound
resistant to LP gas
•
Hand or electric drill
•
Channel lock pliers
•
Noncorrosive
leak-detection
solution
•
Pipe wrench
•
Stud finder
NOTE: The cooktop is manufactured
for use with Natural gas.
To convert to LP gas, see the gas conversion instructions
provided in the literature package.
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See "Electrical Requirements"
and
"Gas Supply Requirements"
sections.
All electrical connections should be made by a licensed, qualified
electrical installer.
Parts needed
•
A UL listed or CSA approved conduit connector
•
UL listed wire connectors
Parts supplied
Check that all parts are included.
•
Anti-tip bracket kit
1"-4
I
m_"q'24.4ore)
a
......................... .........................
ULU
L_q
\
C
A. Anti-tip bracket - 1" (2.5 cm)
B. Anti-tip bracket - 13/4 '' (4.4 cm)
C. #10 x 2" Phillips head screws (2)
NOTE: Brackets must be securely attached to wall stud.
Thickness of finished wall may require longer screws to anchor
bracket to wall. Longer screws are available from your local
hardware store. See "Install Anti-Tip Bracket" section.
•
Backguard and attachment
screws (7).
NOTE: The backguard included with the range is required if
installed with less than 1" (2.5 cm) clearance from a
combustible
rear wall.
IMPORTANT: Observe all governing codes and ordinances.
Do
not obstruct flow of combustion
and ventilation air.
•
It is the installer's responsibility
to comply with installation
clearances specified on the model/serial rating plate. The
model/serial
rating plate is located on the right vertical
surface of the oven door frame.
•
It is recommended
that a 600 CFM range hood be installed
above the range.
•
Recessed installations must provide complete enclosure of
the sides and rear of the range.
•
To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
that projects horizontally a minimum of 5" (12.7 cm) beyond
the bottom of the cabinets.
•
All openings in the wall or floor where range is to be installed
must be sealed.
•
Do not seal the range to the side cabinets.
•
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
•
The wall anti-tip bracket must be installed. To install the anti-
tip bracket shipped with the range, see "Install Anti-Tip
Bracket" section.
•
Grounded electrical supply is required. See "Electrical
Requirements"
section.
•
Proper gas supply connection must be available. See "Gas
Supply Requirements" section.
•
Contact a qualified floor covering installer to check that the
floor covering can withstand at least 200°F (93°C). Use an
insulated pad or 1¼,, ( 0.64 cm) plywood over carpet and under
range if installing range over carpeting.
IMPORTANT: Some cabinet and building materials are not
designed to withstand the heat produced by the oven for baking
and self-cleaning.
Check with your builder or cabinet supplier to
make sure that the materials used will not discolor, delaminate or
sustain other damage.
Hide quick links:
Advertisement
Table of Contents
