Epson PowerLite Home Cinema5030UB User Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Projector
  5. PowerLite Home Cinema5030UB
  6. User manual
Epson PowerLite Home Cinema5030UB User Manual

Epson PowerLite Home Cinema5030UB User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

®
PowerLite
Home Cinema
5030UB/5030UBe User's Guide

Advertisement

Table of Contents
loading

Related Manuals for Epson PowerLite Home Cinema5030UB

Summary of Contents for Epson PowerLite Home Cinema5030UB

  • Page 1 ® PowerLite Home Cinema 5030UB/5030UBe User's Guide...

  • Page 3: Table Of Contents

    Contents PowerLite Home Cinema 5030UB/5030UBe User's Guide ............... 9 Introduction to Your Projector ......................... 10 Projector Features..........................10 Product Box Contents........................11 Additional Components ........................ 12 Optional Equipment and Replacement Parts................. 12 Warranty and Registration Information ..................13 Notations Used in the Documentation ....................14 Where to Go for Additional Information ....................
  • Page 4 Installing Batteries in the Remote Control ..................33 Using Basic Projector Features ....................... 36 Turning On the Projector ........................36 Turning Off the Projector ........................38 Viewing 3D Images ..........................39 Pairing the 3D Glasses with the Projector..................40 Charging the 3D Glasses....................... 41 3D Viewing Range.........................
  • Page 5 Unlocking the Projector's Buttons ..................... 65 Installing a Security Cable ......................65 Saving Settings to Memory and Using Saved Settings ..............65 Using WirelessHD ............................. 67 WirelessHD Transmitter Placement ....................67 Connecting the WirelessHD Transmitter .................... 67 Viewing WirelessHD Content ......................68 Switching WirelessHD Sources......................
  • Page 6 Solving Problems ............................ 107 Projection Problem Tips ........................107 Projector Light Status ........................107 Solving Image Problems ........................111 Solutions When No Image Appears..................... 111 Solutions When "No Signal" Message Appears................112 Displaying From a PC Laptop ....................112 Displaying From a Mac Laptop ....................113 Solutions When "Not Supported"...
  • Page 7 3D Safety Instructions ......................... 131 Restriction of Use ........................133 FCC Compliance Statement......................133 Trademarks ............................134 Open Source Software License......................134 Copyright Notice..........................179 A Note Concerning Responsible Use of Copyrighted Materials........... 180 Copyright Attribution ........................180...

  • Page 9: Powerlite Home Cinema 5030Ub/5030Ube User's Guide

    PowerLite Home Cinema 5030UB/5030UBe User's Guide Welcome to the PowerLite Home Cinema 5030UB/5030UBe User's Guide.

  • Page 10: Introduction To Your Projector

    Introduction to Your Projector Refer to these sections to learn more about your projector and this manual. Projector Features Notations Used in the Documentation Where to Go for Additional Information Projector Part Locations Projector Features The PowerLite Home Cinema 5030UB and 5030UBe projectors include these special features: Bright, high-resolution projection system •...

  • Page 11: Product Box Contents

    • 2.1× optical zoom ratio for improved zooming capability Product Box Contents Additional Components Optional Equipment and Replacement Parts Warranty and Registration Information Parent topic: Introduction to Your Projector Product Box Contents Save all the packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when shipping.

  • Page 12: Additional Components

    • To receive and view a 3D signal, you need a compatible HDMI cable. You can purchase one from Epson or an authorized Epson reseller. If your video source is a 3D Blu-ray disc, you also need a Blu- ray player that supports 3D playback. See your local computer or electronics dealer for purchase information.

  • Page 13: Warranty And Registration Information

    In addition, Epson offers free Extra Care Home Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States, Canada, or Puerto Rico. See the Extra Care Home Service brochure for details.

  • Page 14: Notations Used In The Documentation

    View FAQs (frequently asked questions) and e-mail your questions to Epson technical support 24 hours a day. • If you still need help after checking this manual and the sources listed above, you can use the Epson PrivateLine Support service to get help fast. For details, see "Where to Get Help".

  • Page 15: Projector Parts - Front/Top

    Projector Parts - Front/Top Lamp cover Horizontal and vertical lens shift dials Exhaust vent Remote receiver Lens shutter Lens Air intake/air filter cover Front adjustable foot Control panel and lights Focus ring Zoom ring Parent topic: Projector Part Locations...

  • Page 16: Projector Parts - Rear

    Projector Parts - Rear Cable clip holes HDMI1 port HDMI2 port Component ports Video port PC port (VGA) RS-232C port Trigger out port Service port Remote receiver AC input port Parent topic: Projector Part Locations Related tasks Installing a Security Cable Attaching and Removing the Cable Clips...

  • Page 17: Projector Parts - Base

    Projector Parts - Base Front adjustable feet Mounting bracket holes Cable cover attachment point Air exhaust vent Caution: The air exhaust vent cools the WirelessHD receiver. If you mount the projector on the ceiling, make sure dust does not block the vent or the WirelessHD receiver can overheat. Parent topic: Projector Part Locations...

  • Page 18: Projector Parts - Control Panel

    Projector Parts - Control Panel Status light Lamp light Temp light Menu button (accesses projector menu system) Control panel cover...
  • Page 19 Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons Arrow buttons Esc button (cancels/exits functions) Enter button (selects options) Source button (cycles through the list of sources) Power button/light Parent topic: Projector Part Locations Related references Projector Light Status...

  • Page 20: Projector Parts - Remote Control

    Projector Parts - Remote Control On button (turns on projector) P-in-P button (controls the Picture-in-Picture mode for HDMI inputs) Source buttons (select specific video input sources)
  • Page 21 HDMI Link button (displays the settings menu for HDMI Link) Link Menu button (displays the main menu of the connected device) Control buttons (control playback and other features of connected devices that support the HDMI CEC standard) 2D/3D button (cycles between 2D and 3D modes) Arrow buttons (move though on-screen options) Default button (returns selected setting to default value) Menu button (accesses projector menu system)
  • Page 22 Projector Memory Options - Memory Menu...

  • Page 23: Setting Up The Projector

    Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Projector Placement You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
  • Page 24 Rear Front Ceiling Rear Ceiling...

  • Page 25: Projection Distance

    Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system.
  • Page 26 Screen or image size Projection distance (1) Offset from lens center Offset from lens center Wide to Tele 40 inches (101.6 cm) 57 to 121.7 inches 11 inches (28 cm) 35.0 inches (89 cm) (144 to 309 cm) 60 inches (152.4 cm) 85.8 to 183.5 inches 16.5 inches (42 cm) 52.4 inches (133 cm)

  • Page 27: Projector Connections

    Screen or image size Projection distance (1) Offset from lens center Offset from lens center Wide to Tele 100 inches (254 cm) 117.3 to 250.4 inches 22.4 inches (57 cm) 71.3 inches (181 cm) (298 to 636 cm) 120 inches (304.8 cm) 141.3 to 300.8 inches 26.8 inches (68 cm) 85.8 inches (218 cm)

  • Page 28: Connecting To Video Sources

    Related references Projector Setup Settings - Extended Menu Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector. Connecting to an HDMI Video Source Attaching and Removing the Cable Clips Connecting to an MHL-Compatible Device Connecting to a Component Video Source Connecting to a Composite Video Source Parent topic:...

  • Page 29: Attaching And Removing The Cable Clips

    Note: When an audio/video source that meets the HDMI CEC standard is connected to the projector's HDMI port, you can use the projector's remote control to control certain features of the linked device by pressing the HDMI Link button on the remote control and setting HDMI Link to On. Parent topic: Connecting to Video Sources Related references...

  • Page 30: Connecting To A Component Video Source

    1. Connect the MHL cable or adapter to your device's Micro-USB port. 2. If you are using an MHL adapter, connect it to an MHL-compatible HDMI cable. 3. Connect the other end of the cable to the WirelessHD Transmitter's HDMI 5 / MHL (IN) port. Parent topic: Connecting to Video Sources Connecting to a Component Video Source...

  • Page 31: Connecting To A Composite Video Source

    You can also select the Fast Image Processing setting to reduce lag time. Parent topic: Connecting to Video Sources Related references Input Signal Settings - Signal Menu Connecting to a Composite Video Source If your video source has a composite video port, you can connect it to the projector using an optional RCA-style video or A/V cable.

  • Page 32: Connecting To A Computer For Hdmi Video

    2. Connect the VGA computer cable to your computer's monitor port. 3. Connect the other end to a PC port on the projector. 4. Tighten the screws on the VGA connector. Parent topic: Connecting to Computer Sources Connecting to a Computer for HDMI Video If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.

  • Page 33: Installing Batteries In The Remote Control

    Video source Surround sound Receiver Video cable Parent topic: Projector Connections Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries.
  • Page 34 1. Open the battery cover. 2. Insert the batteries with the + and – ends facing as shown.
  • Page 35 3. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.

  • Page 36: Using Basic Projector Features

    Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features. Turning On the Projector Turning Off the Projector Viewing 3D Images Selecting the Language for the Projector Menus Adjusting the Image Height Image Shape Resizing the Image With the Zoom Ring Focusing the Image Using the Focus Ring Adjusting the Color Convergence (Panel Alignment)
  • Page 37 1. Connect the power cord to the projector's power inlet. 2. Plug the power cord into an electrical outlet. Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. 3. Press the power button on the projector or the On button on the remote control to turn on the projector.

  • Page 38: Turning Off The Projector

    Turning Off the Projector Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown. Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage.

  • Page 39: Viewing 3D Images

    You can view 3D images using your projector. Viewing 3D images requires a 3D-compatible video device and a pair of Epson RF 3D glasses. You can purchase Epson RF 3D glasses from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at epsonstore.com...

  • Page 40: Pairing The 3D Glasses With The Projector

    5. Slide the power switch on the 3D glasses to the On position. 6. Put on the 3D glasses. If you do not see a 3D image, pair the glasses with the projector. Note: If you change the video source or you are not within range of your projector, the glasses enter standby mode and the indicator light flashes green.

  • Page 41: Charging The 3D Glasses

    4. Slide the power switch on the 3D glasses to the On position. 5. Move the glasses within 10 feet (3 m) of the projector, then hold down the Pairing button on the glasses for at least three seconds. The status light on the glasses flashes green and red. If pairing is successful, the light turns green for 10 seconds and then turns off.

  • Page 42: 3D Viewing Range

    1. Connect the smaller end of the charging cable to the port on the bridge of the glasses. Note: Make sure you connect the cable in the correct orientation or you may damage the glasses or cable. 2. Do one of the following: •...

  • Page 43: Selecting The Language For The Projector Menus

    32 ft (10 m) Parent topic: Viewing 3D Images Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2.

  • Page 44: Adjusting The Image Height

    3. Select the Extended menu and press Enter. 4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Using Basic Projector Features Adjusting the Image Height If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet.

  • Page 45: Adjusting The Image Position Using Lens Shift

    If the projected image is unevenly rectangular, you need to adjust the image shape. Adjusting the Image Position Using Lens Shift Parent topic: Using Basic Projector Features Related concepts Image Shape Adjusting the Image Position Using Lens Shift If you cannot install the projector directly in front of the screen, you can adjust the position of the projected image using the lens shift feature.
  • Page 46 Horizontal height × 47% Vertical height × 96% Follow these guidelines when using lens shift to adjust your images: • When adjusting the image height, position the image lower than where you want it to be and then move it up using the vertical lens shift dial. This will help prevent the image from moving down after adjustment.

  • Page 47: Image Shape

    Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality.

  • Page 48: Resizing The Image With The Zoom Ring

    3. Press a keystone button on the projector's control panel to adjust the image shape. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape with the remote control using the Keystone settings in the projector menus.

  • Page 49: Focusing The Image Using The Focus Ring

    2. To enlarge or reduce the image size, rotate the projector's zoom ring. Parent topic: Using Basic Projector Features Focusing the Image Using the Focus Ring 1. Turn on the projector and display an image. Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy.

  • Page 50: Adjusting The Color Convergence (Panel Alignment)

    Parent topic: Using Basic Projector Features Adjusting the Color Convergence (Panel Alignment) You can use the Panel Alignment feature to manually adjust the color convergence (the alignment of the red, green and blue colors) in the projected image. Note: Allow your projector to warm up for at least 10 to 15 minutes and make sure the image is in focus before you use the Panel Alignment feature.
  • Page 51 • B to adjust the blue color convergence. Note: You can only adjust the red or blue color convergence. Green is the standard color panel and cannot be adjusted. 8. Select the Pattern Color setting and press Enter. 9. Select the pattern you want to use and press Enter. 10.

  • Page 52: Remote Control Operation

    14. Do one of the following: • If your projector's panel alignment is now correct, select Exit and press Enter to return to the Panel Alignment menu. • If your projector needs additional panel alignment, select Select intersection and adjust and press Enter.
  • Page 53 Vertical 32 feet (10 m) ± 30° 60° 10°...

  • Page 54: Selecting An Image Source

    Horizontal 32 feet (10 m) ± 30° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.

  • Page 55: Projection Modes

    2. For video image sources, insert a DVD or other video media and press its play button, if necessary. 3. Do one of the following: • Press the Source button on the projector until you see the image from the source you want. •...

  • Page 56: Changing The Projection Mode Using The Menus

    • Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount. • Rear flips the image horizontally to project from behind a translucent screen. • Rear/Ceiling flips the image over top-to-bottom and horizontally to project from the ceiling and behind a translucent screen.

  • Page 57: Image Aspect Ratio

    Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio. However, for certain images you can change the aspect ratio to fit your screen by pressing a button on the remote control. If you always want to use a particular aspect ratio for a certain video input source, you can select it using the projector's menus.

  • Page 58: Color Mode

    Note: Black bands and cropped images may project in certain aspect ratios, depending on the aspect ratio and resolution of your input signal. Aspect ratio setting Description Auto Automatically sets the aspect ratio according to the input signal. Normal Displays images using the full projection area and maintains the aspect ratio of the image.

  • Page 59: Changing The Color Mode

    Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. 1. Turn on the projector and switch to the image source you want to use. 2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary.

  • Page 60: Turning On Auto Iris

    Color Mode Description 3D Dynamic Best for projecting in a bright room 3D Cinema Best for movies projected in a dark room 3D THX Best for projecting in a dark room Parent topic: Color Mode Turning On Auto Iris In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project.

  • Page 61: Using Picture In Picture

    • Normal for standard brightness adjustment. Note: You can set Auto Iris for each Color Mode that supports the feature. 5. Press Menu or Esc to exit the menus. Parent topic: Color Mode Using Picture in Picture You can use the Picture in Picture mode to view two image sources simultaneously. Note: You can only display HDMI or WirelessHD video sources when Picture in Picture mode is active.
  • Page 62 Setting Description Subscreen Size Adjusts the size of the sub-screen Subscreen Position Adjusts the location where the sub-screen is displayed Subscreen Source Selects which source appears in the sub-screen (PowerLite Home Cinema 5030UBe) Swap Main/Sub Switches the video source displayed on the main screen with the source displayed on the sub-screen Exit Picture in Picture Closes the sub-screen and resumes normal projection...

  • Page 63: Adjusting Projector Features

    Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments. Shutting Off the Picture Temporarily Projector Security Features Saving Settings to Memory and Using Saved Settings Shutting Off the Picture Temporarily You can temporarily turn off the projected picture if you want to redirect your audience's attention during a presentation.

  • Page 64: Locking The Projector's Buttons

    Locking the Projector's Buttons You can lock the buttons on the projector's control panel to prevent anyone from using the projector. You can lock all the buttons or all the buttons except the power button. 1. Press the Menu button. 2.

  • Page 65: Unlocking The Projector's Buttons

    Locking the Projector's Buttons Installing a Security Cable You can use the security slot on the back of the projector to attach a Kensington Microsaver Security system, available from Epson. Parent topic: Projector Security Features Saving Settings to Memory and Using Saved Settings You can save customized settings for each of your video inputs and then select the saved settings whenever you want to use them.
  • Page 66 5. Select one of the following options: • Load Memory: Overwrites your current settings with saved settings • Save Memory: Saves your current settings to memory (10 memories with different names are available) Note: A memory name that is being used is indicated by a green mark. Saving over a previously saved memory overwrites the settings with your current settings.

  • Page 67: Using Wirelesshd

    Using WirelessHD You can use the included WirelessHD transmitter to wirelessly stream HD content from a video device to the projector (PowerLite Home Cinema 5030UBe). WirelessHD Transmitter Placement Connecting the WirelessHD Transmitter Viewing WirelessHD Content Switching WirelessHD Sources Using the WirelessHD Picture-in-Picture Feature WirelessHD Transmitter Placement Keep these considerations in mind as you select a WirelessHD transmitter location: •...

  • Page 68: Viewing Wirelesshd Content

    2. Connect HDMI cables to your video devices and to the HDMI input ports on the side and back of the WirelessHD transmitter. Note: You can connect an MHL-compatible smartphone or tablet to the HDMI 5 / MHL (IN) port on the WirelessHD Transmitter.

  • Page 69: Switching Wirelesshd Sources

    3. Press the WirelessHD button on the remote control. The WiHD light on the transmitter lights up and your projector displays WirelessHD content. Note: If the WirelessHD connection fails, press the Setup button on the bottom of the WirelessHD transmitter and try again. Parent topic: Using WirelessHD Switching WirelessHD Sources...

  • Page 70: Using The Wirelesshd Picture-In-Picture Feature

    2. Press the Input button repeatedly to highlight different input sources. 3. When you have highlighted the source you want to switch to, release the Input button. The display automatically switches to the highlighted source after a few seconds. Parent topic: Using WirelessHD Using the WirelessHD Picture-in-Picture Feature If you have connected multiple video sources to the WirelessHD transmitter, you can use the Picture-in-...
  • Page 71 • Press and hold the P-in-P button on the remote control to switch the sources shown in the main display and the sub-screen. 3. When you are finished watching Picture-in-Picture, press the P-in-P button on the remote control to resume normal projection. Parent topic: Using WirelessHD...

  • Page 72: Adjusting The Menu Settings

    Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings. Using the Projector's Menus Image Quality Settings - Image Menu Input Signal Settings - Signal Menu Projector Feature Settings - Settings Menu Projector Setup Settings - Extended Menu Projector Memory Options - Memory Menu Projector Information Display - Info Menu...

  • Page 73: Image Quality Settings - Image Menu

    2. Press the up or down arrow buttons to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4.
  • Page 74 To change settings for an input source, make sure the source is connected and select that source. Setting Options Description Color Mode See the list of available Color Adjusts the vividness of image Modes colors for various image types and environments Brightness Varying levels available Lightens or darkens the overall...
  • Page 75 RGB: adjusts the offset and gain for each color RGBCMY: adjusts the hue, saturation, and brightness for each color EPSON Super White: reduces over-exposure of whites in your image; can be set only when Color Mode is set to Natural, Cinema, THX, 3D THX, B&W Cinema, or 3D Cinema.

  • Page 76: Input Signal Settings - Signal Menu

    Parent topic: Adjusting the Menu Settings Related concepts Color Mode Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source.
  • Page 77 Setting Options Description 3D Setup 3D Display Selects various 3D options 2D-to-3D Conversion 3D Display: enables 3D mode 3D Format 2D-to-3D Conversion: converts 2D images to 3D 3D Depth 3D Format: selects the 3D Diagonal Screen Size format 3D Brightness 3D Depth: sets the depth for the Inverse 3D Glasses 3D image...
  • Page 78 Setting Options Description Deinterlacing Sets whether to convert interlaced-to-progressive signals Video for certain video image types Film/Auto Off: for fast-moving video images Video: for most video images Film/Auto: for movies, computer graphics, and animation Motion Detection 1 to 5 Selects how the image is converted to a progressive signal (Adjust this setting if you experience problems with still...
  • Page 79 WirelessHD (PowerLite Home Cinema 5030UBe) video sources. • You can set the HDMI Video Range setting only when the Epson Super White setting is set to Off. • The Reset setting does not reset the Diagonal Screen Size, 3D Viewing Notice, Aspect, and Image Processing settings.

  • Page 80: Projector Feature Settings - Settings Menu

    Parent topic: Adjusting the Menu Settings Related concepts Image Aspect Ratio Related tasks Viewing 3D Images Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features. Setting Options Description Keystone Varying levels available Adjusts image shape to rectangular (vertically)
  • Page 81 Setting Options Description HDMI Link Device Connections Adjusts the HDMI Link options that allow the projector remote to HDMI Link control HDMI-connected devices Power On Link that support the CEC standard Power Off Link Device Connections: lists the devices connected to the HDMI1 and HDMI2 ports HDMI Link: enables or disables the HDMI Link function...
  • Page 82 Setting Options Description WirelessHD Device Connections Device Connections: displays a list of available WirelessHD (PowerLite Home Cinema WirelessHD devices 5030UBe) Reception WirelessHD: controls whether WiHD Mode the projector receives WirelessHD signals Reception: displays the strength of the WirelessHD signal WiHD Mode: adjusts the WirelessHD signal strength and range •...

  • Page 83: Projector Setup Settings - Extended Menu

    Setting Options Description User Button 2D-to-3D Conversion Assigns a menu option to the User button on the remote 3D Depth control for one-touch access 3D Brightness Inverse 3D Glasses Power Consumption Info Picture in Picture See the list of available Picture in Adjusts the size and location of Picture options the sub-screen, swaps sources and exits Picture in Picture mode...
  • Page 84 Setting Options Description Operation Direct Power On Selects various operation options Sleep Mode Direct Power On: lets you turn Illumination on the projector without pressing Trigger Out the power button High Altitude Mode Sleep Mode: automatically turns off the projector after an interval of inactivity Illumination: turns off the lights on the projector...
  • Page 85 Setting Options Description Display Menu Position Selects various display options Menu Color Menu Position: adjusts the location where the menu is Messages displayed Display Background Menu Color: selects the color of Startup Screen the menu Standby Confirmation Messages: controls whether messages are displayed on the screen Display Background: selects...

  • Page 86: Projector Memory Options - Memory Menu

    Setting Options Description Panel Alignment Panel Alignment Corrects color misalignment in the projected image Select Color Panel Alignment: enables Pattern Color adjustments for color Start Adjustments convergence (the alignment of the red and blue colors in the projected image) Select Color: specifies the color convergence to correct Pattern Color: specifies the color pattern used during panel...

  • Page 87: Projector Information Display - Info Menu

    Setting Description Load Memory Displays the list of customized settings entries that you have created; select an entry and press Enter on the remote control to load it Save Memory Saves the current projector settings to the projector's memory Erase Memory Displays the list of customized settings entries that you have created;...
  • Page 88 Displays the number of hours (H) the lamp has been used in each Power Consumption mode; if the information is displayed in yellow, obtain a genuine Epson replacement lamp soon Source Displays the name of the port to which the current input source is...

  • Page 89: Projector Reset Options - Reset Menu

    Information item Description Version Displays the firmware version of the projector Parent topic: Adjusting the Menu Settings Related references Optional Equipment and Replacement Parts Related tasks Replacing the Lamp Resetting the Lamp Timer Projector Reset Options - Reset Menu You can reset most of the projector settings to their default values using the Reset All option on the Reset menu.
  • Page 90 Parent topic: Adjusting the Menu Settings...

  • Page 91: Maintaining And Transporting The Projector

    The only parts you should replace are the lamp, air filter, and remote control batteries. If any other part needs replacing, contact Epson or an authorized Epson servicer. Warning: Before cleaning any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except as specifically explained in this manual.

  • Page 92: Cleaning The 3D Glasses

    • To remove dust or smudges, gently move the shutter to the side and wipe the lens with lens-cleaning paper. • To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas.

  • Page 93: Cleaning The Projector Case

    Filter maintenance intervals will depend on the environment. If regular maintenance is not performed, your Epson projector will notify you when the temperature inside the projector has reached a high level. Do not wait until this warning appears to maintain your...

  • Page 94: Cleaning The Air Filter

    Damage due to the failure to properly maintain the projector or its filter may not be covered by the projector or lamp Limited Warranties. Cleaning the Air Filter Replacing the Air Filter Parent topic: Projector Maintenance Related references Projector Light Status Cleaning the Air Filter You need to clean the projector's air filter in the following situations: •...
  • Page 95 3. Pull the air filter out of the projector. 4. Tap each side of the air filter 4 to 5 times to shake off any excess dust. Caution: Do not use excessive force when tapping the air filter, or it may crack and become unusable.

  • Page 96: Replacing The Air Filter

    5. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust. Note: If dust is difficult to remove or the air filter is damaged, replace the air filter. 6. Place the air filter back in the projector as shown. 7.
  • Page 97 • If the filter is a dark gray color You can replace the air filter while the projector is mounted to the ceiling or placed on a table. 1. Turn off the projector and unplug the power cord. 2. Press in on the inner edge of the air filter cover to release the latch, then pull to remove. 3.

  • Page 98: Projector Lamp Maintenance

    4. Place the new air filter in the projector as shown. 5. Close the air filter cover. Parent topic: Air Filter and Vent Maintenance Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
  • Page 99 You can replace the lamp while the projector is mounted to the ceiling, if necessary. 1. Turn off the projector and unplug the power cord. 2. Allow the projector lamp to cool down for at least one hour. 3. Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp cover.
  • Page 100 4. Slide the lamp cover out and lift it off. 5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out.
  • Page 101 6. Lift up the lamp handle and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 7.
  • Page 102 8. Push in the lamp firmly and tighten the screws to secure it. Caution: Do not over-tighten the screws. 9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp’s usage.

  • Page 103: Resetting The Lamp Timer

    Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly. Note: Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage information.

  • Page 104: Replacing The Remote Control Batteries

    Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries.
  • Page 105 3. Insert the batteries with the + and – ends facing as shown. 4. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame.

  • Page 106: Transporting The Projector

    • When shipping the projector for repairs, place it in its original packing materials, if possible, or use equivalent materials with cushioning around the projector. Mark the box "Fragile." Note: Epson shall not be liable for any damages incurred during transportation. Parent topic:...

  • Page 107: Solving Problems

    • The lights on the projector may indicate what the problem is. • The solutions in this manual can help you solve many problems. If none of these solutions help, you can contact Epson for technical support. Parent topic: Solving Problems...
  • Page 108 Status light Lamp light Temp light Power light Power light Status light Lamp light Temp light Status and solution Blue Blue Normal operation Blue Flashing blue Warming up; wait for an image to appear Standby or sleep mode...
  • Page 109 • Clean or replace the air filter • If operating the projector at high altitude, turn on High Altitude Mode • If the problem persists, unplug the projector and contact Epson for help...
  • Page 110 Epson for help Flashing blue Flashing Flashing Auto Iris error; turn the projector off, orange orange unplug it, and contact Epson for help Flashing blue Orange Orange Power error (ballast); turn the projector off, unplug it, and contact Epson for help...

  • Page 111: Solving Image Problems

    Related tasks Cleaning the Air Filter Replacing the Lamp Replacing the Air Filter Solving Image Problems Check the solutions in these sections if you have any problems with projected images. Solutions When No Image Appears Solutions When "No Signal" Message Appears Solutions When "Not Supported"...

  • Page 112: Solutions When "No Signal" Message Appears

    • For images projected from applications using Windows DirectX, turn off DirectX functions. Parent topic: Solving Image Problems Related references Image Quality Settings - Image Menu Projector Setup Settings - Extended Menu Solutions When "No Signal" Message Appears If the "No Signal" message appears, try the following solutions: •...

  • Page 113: Displaying From A Mac Laptop

    Parent topic: Solutions When "No Signal" Message Appears Displaying From a Mac Laptop If you see the "No Signal" message when you display from a Mac laptop, you need to set up the laptop for mirrored display. (See your laptop manual for details.) 1.

  • Page 114: Solutions When The Image Is Not Rectangular

    Parent topic: Solving Image Problems Related references Input Signal Settings - Signal Menu Supported Video Display Formats Solutions When the Image is Not Rectangular If the projected image is not evenly rectangular, try the following solutions: • Place the projector directly in front of the center of the screen, facing it squarely, if possible. •...

  • Page 115: Solutions When The Image Is Fuzzy Or Blurry

    • If you connected an extension power cable, try projecting without it to see if it caused interference in the signal. Parent topic: Solving Image Problems Related references Input Signal Settings - Signal Menu Image Quality Settings - Image Menu Supported Video Display Formats Solutions When the Image is Fuzzy or Blurry If the projected image is fuzzy or blurry, try the following solutions:...

  • Page 116: Solutions When A 3D Image Does Not Display Correctly

    Auto, but in some cases you may need to select a different setting to match the 3D signal from your video device. • Make sure you are using RF 3D active shutter glasses. You can purchase them from Epson. • Make sure your 3D glasses are turned on and fully charged. If the glasses have entered standby mode, slide the power switch on the glasses to the Off position and then back to the On position.

  • Page 117: Solutions When A Wirelesshd Source Does Not Display Correctly

    • If the other solutions do not not solve the problem, change the Inverse 3D Glasses setting on the Signal menu. Return the setting to its original value if changing it does not solve the problem. Parent topic: Solving Image Problems Related references Projector Feature Settings - Settings Menu 3D Viewing Range...

  • Page 118: Solving Projector Or Remote Control Operation Problems

    • The projector's buttons may be locked for security. Unlock the buttons or use the remote control to turn on the projector. • The power cord may be defective. Disconnect the cord and contact Epson. • If the projector's lamp shuts off unexpectedly, it may have entered sleep mode after a period of inactivity.

  • Page 119: Solutions To Problems With The Remote Control

    Projector Feature Settings - Settings Menu Related tasks Replacing the Remote Control Batteries Where to Get Help If you need to contact Epson for technical support services, use the following support options. Internet Support Visit Epson's support website at epson.com/support (U.S.) or...
  • Page 120 Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a projector support specialist by dialing (562) 276-4394 (U.S.) or (905) 709-3839 (Canada).

  • Page 121: Technical Specifications

    Technical Specifications These sections list the technical specifications of your projector. General Projector Specifications Projector Lamp Specifications Remote Control Specifications Projector Dimension Specifications Projector Electrical Specifications Projector Environmental Specifications Projector Safety and Approvals Specifications Supported Video Display Formats General Projector Specifications Type of display Poly-silicon TFT active matrix Resolution...

  • Page 122: Projector Lamp Specifications

    Image size 30 inches (0.76 m) to 300 inches (7.62 m) (in native aspect ratio) Projection distance 34 inches (0.87 m) to 754 inches (19.15 m) (in native aspect ratio) Projection methods Front, rear, ceiling-mounted Optical aspect ratio 16:9 (width-to-height) Focus adjustment Manual Zoom adjustment...

  • Page 123: Remote Control Specifications

    Remote Control Specifications Reception range 32 feet (10 m) Batteries Two alkaline or manganese AA Parent topic: Technical Specifications Projector Dimension Specifications Height (excluding feet) 5.51 inches (140 mm) Width 18.35 inches (466 mm) Depth 15.55 inches (395 mm) Weight PowerLite Home Cinema 5030UB: 18.4 lb (8.4 kg) PowerLite Home Cinema 5030UBe:...

  • Page 124: Projector Environmental Specifications

    For best results, your computer's monitor port or video card resolution should be set to display in the projector's native resolution. However, your projector includes Epson's SizeWise chip that supports other computer display resolutions, so your image will be resized to fit automatically.
  • Page 125 Display format Refresh rate (in Hz) Resolution (in pixels) 60/70/75/85 1024 × 768 WXGA 1280 × 768 1366 × 768 60/75/85 1280 × 800 SXGA 70/75/85 1152 × 864 1280 × 960 1280 × 1024 WXGA++ 1600 × 900 Composite video TV (NTSC) 720 ×...
  • Page 126 Display format Refresh rate (in Hz) Resolution (in pixels) SDTV (480i/480p) 720 × 480 SDTV (576i/576p) 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30/50/60 1920 × 1080 MHL input signals (PowerLite Home Cinema 5030UBe) SDTV (480i/480p) 720 ×...
  • Page 127 Display format Refresh rate (in Hz) Resolution (in pixels) 3D formats HDTV750p (720p) 50/60 1280 × 720 Side by Side Top and Bottom HDTV1125i (1080i) 50/60 1920 × 1080 Side by Side HDTV1125p (1080p) 50/60 1920 × 1080 — 1920 × 1080 Side by Side Top and Bottom Parent topic:...

  • Page 128: Notices

    Important Safety Instructions FCC Compliance Statement Trademarks Open Source Software License Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to epson.com/recycle for information on how to return your products for proper disposal. Parent topic: Notices Important Safety Information Caution: Never look into the projector lens when the lamp is turned on;...

  • Page 129: Important Safety Instructions

    Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes. •...
  • Page 130 • Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector. • If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the projectors to allow for proper ventilation.

  • Page 131: 3D Safety Instructions

    • Do not store the projector outside of the required temperature range of 14 to 140 ºF (–10 to 60 ºC) or in direct sunlight for long periods of time. Doing so may cause damage to the case. • Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not bring your hands or face close to the vents while projection is in progress.
  • Page 132 muscle twitching, loss of awareness, altered vision, involuntary movements, disorientation, eye strain, nausea/vomiting, dizziness, headaches, fatigue, or blurry/double vision that lasts longer than few seconds. Do not engage in any potentially hazardous activity (such as driving a vehicle or operating machinery) until your symptoms have completely gone away.

  • Page 133: Restriction Of Use

    • Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by flashing light effects • SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF EPILEPSY. • Do not leave the 3D glasses or any parts supplied with the glasses within reach of children. They could be accidentally swallowed.

  • Page 134: Trademarks

    HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks. Parent topic: Notices...
  • Page 135 We provide the source code of the GPL Programs until five (5) years after the discontinuation of same model of this projector product. If you desire to receive the source code of the GPL Programs, contact Epson as described in the User's Guide.
  • Page 136 The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it.
  • Page 137 Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program).
  • Page 138 In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3.
  • Page 139 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein.
  • Page 140 10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
  • Page 141 We provide the source code of the LGPL Programs until five (5) years after the discontinuation of same model of this projector product. If you desire to receive the source code of the LGPL Programs, please see the "EPSON Projector Contact List" in the User's Guide, and contact the customer support of your region.
  • Page 142 The list of LGPL Programs is as follows and the names of author are described in the source code of the LGPL Programs. LGPL Programs glibc-2.8 SDL-1.2.13 SDL-Image The GNU Lesser General Public License Version 2 is as follows. You also can see the GNU Lesser General Public License Version 2 at http://www.gnu.org/licenses/.
  • Page 143 source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library.
  • Page 144 Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. The precise terms and conditions for copying, distribution and modification follow.
  • Page 145 a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.
  • Page 146 complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.
  • Page 147 and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library.
  • Page 148 9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.
  • Page 149 Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.
  • Page 150 Copyright (c) <year> <name of author> This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.
  • Page 151 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3.
  • Page 152 2. You can use this software for whatever you want. You don't have to pay us. 3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that you've used the IJG code. In legalese: The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for a particular purpose.
  • Page 153 It appears that the arithmetic coding option of the JPEG spec is covered by patents owned by IBM, AT&T, and Mitsubishi. Hence arithmetic coding cannot legally be used without obtaining one or more licenses. For this reason, support for arithmetic coding has been removed from the free JPEG software. (Since arithmetic coding provides only a marginal gain over the unpatented Huffman mode, it is unlikely that very many implementations will support it.) So far as we are aware, there are no patent restrictions on the remaining code.
  • Page 154 libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c) 2000-2002 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.6 with the following individuals added to the list of Contributing Authors Simon-Pierre Cadieux Eric S.
  • Page 155 Guy Eric Schalnat Paul Schmidt Tim Wegner The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors and Group 42, Inc. assume no liability for direct, indirect, incidental, special, exemplary, or consequential damages, which may result from the use of the PNG Reference Library, even if advised of the possibility of such damage.
  • Page 156 zlib-1.1.4 License terms of conditions of each program which are provided by owner of the copyright to the "zlib" are as follows. Copyright notice: (c) 1995-1998 Jean-loup Gailly and Mark Adler This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.
  • Page 157 http://www.apache.org/licenses/ TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION 1. Definitions. "License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document. "Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License.
  • Page 158 "Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and subsequently incorporated within the Work. 2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and such Derivative Works in Source or Object form.
  • Page 159 Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the conditions stated in this License. 5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this License, without any additional terms or conditions.
  • Page 160 that a file or class name and description of purpose be included on the same "printed page" as the copyright notice for easier identification within third-party archives. Copyright [yyyy] [name of copyright owner] Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License.
  • Page 161 Copyright (c) 1994-2007 Red Hat, Inc. All rights reserved. This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY expressed or implied, including the implied warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
  • Page 162 THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED WARRANTY. IN PARTICULAR, NEITHER THE AUTHOR NOR AT&T MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE. ----------- The author of this software is David M.
  • Page 163 5900 E. Ben White Blvd. Austin, TX 78741 800-292-9263 (5) C.W. Sandmann Copyright (C) 1993 C.W. Sandmann This file may be freely distributed as long as the author's name remains. (6) Eric Backus (C) Copyright 1992 Eric Backus This software may be used freely so long as this copyright notice is left intact. There is no warrantee on this software.
  • Page 164 All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  • Page 165 (13) Royal Institute of Technology Copyright (c) 1999 Kungliga Tekniska Hökolan (Royal Institute of Technology, Stockholm, Sweden). All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
  • Page 166 DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  • Page 167 THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;...
  • Page 168 LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (19) Todd C.
  • Page 169 Intel hereby grants you permission to copy, modify, and distribute this software and its documentation. Intel grants this permission provided that the above copyright notice appears in all copies and that both the copyright notice and this permission notice appear in supporting documentation. In addition, Intel grants this permission provided that you prominently mark as "not part of the original"...
  • Page 170 (27) Konstantin Chuguev (--enable-newlib-iconv) Copyright (c) 1999, 2000 Konstantin Chuguev. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  • Page 171 LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (30) - Alex Tatmanjants (targets using libc/posix) Copyright (c) 1995 Alex Tatmanjants <alex@elvisti.kiev.ua>...
  • Page 172 THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;...
  • Page 173 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS"...
  • Page 174 Copyright (c) 2009 CodeSourcery, Inc. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  • Page 175 * * Neither the name of MIPS Technologies Inc. nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
  • Page 176 FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. TOPPERS/JSP This projector product includes the open source software program "TOPPERS/JSP"...
  • Page 177 (a) The above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.). (b) The TOPPERS Project shall be notified owing to a method in which the form of distribution is decided otherwise.
  • Page 178 This product includes software developed by the University of California, Berkeley and its contributors. 4. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS"...

  • Page 179: Copyright Notice

    Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.

  • Page 180: A Note Concerning Responsible Use Of Copyrighted Materials

    A Note Concerning Responsible Use of Copyrighted Materials Epson encourages each user to be responsible and respectful of the copyright laws when using any Epson product. While some countries' laws permit limited copying or reuse of copyrighted material in certain circumstances, those circumstances may not be as broad as some people assume. Contact your legal advisor for any questions regarding copyright law.

This manual is also suitable for:

Powerlite home cinema 5030ubePowerlite home cinema 5030ub

Table of Contents