Table of Contents
Advertisement
Available languages
Available languages
Recessed
area or closet installation
The dimensions shown are for the recommended
spacing
allowed (A and B), except the closet door ventilation openings.
The dimensions shown for the closet door ventilation openings
(C) are the minimum required.
19" T
(48,3 0m)
J[_
olo
i_ max.
I,/.1 (3b,b cm)
C
0"-_}_-- 27" --_-0"
_1 1"I* 26_/2
'' *1
(Ocm) "
(68,6cm) " (Ocm) (2,5cm)(64,8cm)
A
B
---_
3"
(7,6 cm)
_'--48 in, 2
(310cm2)- . _"
--_
24i02_.
31
(155 c m 2 )
(7,6 c m)
_-4"
-'_
(10,2 ¢ m)
C
A. Front view
B. Side view
C. Closet door with vents
•
Additional spacing should be considered for ease of
installation and servicing.
•
Additional clearances may be required for wall, door and floor
moldings.
•
Additional spacing of 1" (2.5 cm) on all sides of the washer is
recommended
to reduce noise transfer.
If a closet door is installed, the minimum air openings in the
top and bottom of the door are required (C). Louvered doors
with air openings in the top and bottom are acceptable.
Companion appliance spacing should also be considered.
t_'}_¢ _, _ ¢__
The washer can be installed using the standpipe drain system
(floor or wall), the laundry tub drain system, or the floor drain
system. Select the drain hose installation method you need. See
"Tools and Parts."
Standpipe drain system--wall
or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of
2" (5 cm). The minimum carry-away capacity can be no less than
17 gal. (64 L) per minute. A 1 V4" (3.2 cm) diameter to 1" (2.5 cm)
diameter standpipe adapter kit is available. See "Tools and
Parts."
The top of the standpipe must be at least 39" (99 cm) high and no
higher than 96" (244 cm) from the bottom of the washer.
To avoid siphoning, no more than 8" (20.3 cm) of drain hose
should be inside the standpipe. Secure drain hose with beaded
tie strap.
39"
(99 crn)
A
B
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 39" (99 cm) above the floor
and no higher than 96" (244 cm) from the bottom of the washer.
Floor drain system (view D)
The floor drain system requires a siphon break that may be
purchased separately. See "Tools and Parts."
The siphon break must be a minimum of 28" (71 cm) from the
bottom of the washer. Additional hoses might be needed.
To avoid siphoning, no more than 8" (20.3 cm) of drain hose
should be below the top of the wash tub. Secure drain hose with
beaded tie strap.
C
D
Electrical
Shock Hazard
Plug into a grounded
3 prong outlet.
Do not remove ground
prong.
Do not use an adapter.
Do not use an extension
cord.
Failure to follow
these instructions can result in death,
fire, or electrical
shock.
•
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical
supply is required. A time-delay fuse or circuit breaker is
recommended.
It is recommended
that a separate circuit
serving only this appliance be provided.
•
This washer is equipped with a power supply cord having a 3
prong grounding
plug.
•
To minimize possible shock hazard, the cord must be
plugged into a mating, grounded 3 prong outlet, grounded in
accordance
with local codes and ordinances.
If a mating
outlet is not available, it is the personal responsibility
and
obligation of the customer to have the properly grounded
outlet installed by a qualified electrician.
•
If codes permit and a separate ground wire is used, it is
recommended
that a qualified electrician determine that the
ground path is adequate.
•
Do not ground to a gas pipe.
Advertisement
Table of Contents
