Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Response Alarms Eclipse E100 Wirefree
Summary of Contents for Response Alarms Eclipse E100 Wirefree
- Page 1 E100 Wirefree Alarm System Installation & Operating Manual...
-
Page 2: Table Of Contents
FOREWORD CONTENTS Page No. Your decision to purchase an Eclipse Wirefree Solar INTRODUCTION Alarm System represents a major and sensible step towards total protection of your premises, its contents PLANNING AND EXTENDING YOUR WIREFREE SOLAR ALARM SYSTEM and its occupants. The Eclipse Wirefree Solar Alarm System complies with WIREFREE EXTERNAL SOLAR SIREN the requirements of BS6799 Class 1 for Wireless Alarms. -
Page 3: Introduction
INTRODUCTION The Eclipse Wirefree Solar Alarm System contains all components necessary to install a complete system. Wirefree items included are: Wirefree External Solar Siren 2 x PIR Movement Detectors 1 x Remote Control Wirefree Passive Infra Red Movement Detectors (PIR’s) Wirefree External Solar Siren PANIC WP1.2-6... -
Page 4: Planning And Extending Your Wirefree Solar Alarm System
PLANNING AND EXTENDING YOUR WIREFREE ALARM SYSTEM For even greater protection you can fit as many System is designed to give you protection for a two PlR Movement Detectors and Magnetic Contact bedroomed house. Just add additional detectors Detectors as and when you require. The Eclipse Alarm where further protection is needed. -
Page 5: Wirefree External Solar Siren
WIREFREE EXTERNAL SOLAR SIREN GENERAL INFORMATION HOUSING NORTH Siren and Solar Panel are all encapsulated within Avoid if a tough polycarbonate housing. This housing provides possible full protection against adverse weather conditions. All electronic components are specially treated to ensure long, reliable, trouble free operation and an integral tamper switch gives maximum security protection to EAST... -
Page 6: Settings
Solar Panel Front cover 7.5 Volt DC locating tabs charging adaptor Receiver input Aerial Dip switch cover Bleep Disable Link Tamper switch Siren Disable Link J.D. Link 6 Volt 1.2Ahr rechargeable battery House Code 9 Volt PP3 initial dip switches 1-8 power up battery Printed circuit board enclosure... -
Page 7: Remote Control Unit
Detection. In order to detect any attempts to illegally HOUSE CODE jam the radio channel used with your alarm system a Inside you will find a row of 8 dip special jamming detection function is incorporated switches 1 - 8. This is your House PANIC into the Solar Siren. -
Page 8: Wirefree Passive Infra Red Movement
WIREFREE PASSIVE 4. Where possible, mount the detector so that the logical path of an intruder would cut across the fan INFRA RED MOVEMENT patterns rather than directly towards the detector. DETECTORS (PlR’s) Any number of PIR Movement Detectors can be used with your system, providing they are all coded with the Two Passive Infra Red Movement Detectors are supplied System House Code and are within the radio range of... -
Page 9: Installation
House Code cover. After the battery has been connected for Anti Tamper approximately 40 seconds the PIR Movement Switch Detector will become active causing the LED above the detector window to flash every time movement is detected. Where Two Pulse Count Detection has been selected the LED will be dim on first detection and brighter on the second. -
Page 10: Testing The System
Fix the detector and magnet to the opening using 4. Using a ball-point pen, set the miniature switches either the double sided tape screws provided. 1-8 to the same combination of ‘ON’ and ‘OFF’ as the dip switches in the Solar Siren. Before fixing the detector to a metal door/window check the radio range as previously described. -
Page 11: Operating Instructions
To test the optional Magnetic Contact Detectors, Arm alarm condition is initiated accidently the alarm can be the system using the remote control. Open the stopped immediately by pressing and releasing the protected door/window and ensure that the Solar ‘OFF’ button on the Remote Control. Siren goes into Alarm Mode. -
Page 12: Maintenance
battery(ies) as required turn the Solar Siren back to DETECTORS & REMOTE CONTROL Disarmed Mode. The Detectors and Remote Control(s) require no Note: When replacing PIR batteries, fit PP3 Alkaline maintenance. Simply replace the batteries once a year or type. Rechargeable batteries should NOT be fitted. when a low battery is indicated. -
Page 13: Trouble Shooting
TROUBLE SHOOTING Symptom Recommendation Symptom Recommendation Siren gives full alarm condition when arming PIR Movement Detector not detecting a person’s movement Rear anti-tamper switch on siren is open - ensure Check battery connections are good. that it is pressed fully closed. The wall is possibly uneven, the siren may need relocating to a more 2. -
Page 14: Extending Your System
EXTENDING YOUR E100 WIREFREE ALARM SYSTEM You may add Wirefree Magnetic Contact Detectors and additional Wirefree PIR Detectors etc. from the CA2000 range of accessories as required, to give additional protection where needed. The following accessories are also available to extend and enhance your system. - Page 15 For security, Recorded or Registered Post is recommended. 17 Church Road, Great Bookham, Surrey KT23 3PG Telephone: 01372 450960 E-mail: info@wireless-alarms.net www.wireless-alarms.net E100 Wirefree Alarm System Response...
-
Page 16: Specification
ECLIPSE E100 SPECIFICATION Wirefree External Solar Siren Remote Control User changeable four digit access code On-Air indicator Case material 3mm Polycarbonate 15 second Entry/Exit Delay facility Dual front and rear anti-tamper Anti-tamper Internal receiver and aerial UK Indoor use only frequency 418MHz Dual Personal Attack buttons Sealed lead acid...
Need help?
Do you have a question about the Eclipse E100 Wirefree and is the answer not in the manual?
Questions and answers