Table of Contents
Advertisement
Quick Links
Gigabit Ethernet Switch
User's Guide
Version 1.0
P/N: ATNSGD5082503 Rev.1
This User's Guide contains important information regarding the
installation of your switch. Please read it completely before
beginning installation.
For future reference, record the serial number
of your network switch in the space below:
SERIAL number
The serial number is located on the bottom of the switch.
Advertisement
Table of Contents
Related Manuals for Amer.com Gigabit Ethernet Switch
Summary of Contents for Amer.com Gigabit Ethernet Switch
- Page 1 Gigabit Ethernet Switch User’s Guide Version 1.0 P/N: ATNSGD5082503 Rev.1 This User's Guide contains important information regarding the installation of your switch. Please read it completely before beginning installation. For future reference, record the serial number of your network switch in the space below: SERIAL number The serial number is located on the bottom of the switch.
- Page 3 Amer.com 7259 Bryan Dairy Road, Largo, FL 33777 USA © Amer.com Corp., 1997-2002 All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from Amer.com, as stipulated by the United States Copyright Act of 1976.
- Page 4 Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected to. Consult the dealer or an experienced radio/TV technician for help. Shielded interface cables must be used in order to comply with emission limits. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
-
Page 5: Table Of Contents
ABLE OF ONTENTS ABOUT THIS GUIDE ..........4 ..................4 ERMS ’ ..........4 VERVIEW OF THIS UIDE INTRODUCTION ............5 ..........5 IGABIT THERNET ECHNOLOGY ............5 WITCHING ECHNOLOGY ..................6 EATURES UNPACKING AND SETUP ........11 ................11 NPACKING .................. -
Page 6: About This Guide
H I S U I D E This user’s guide tells you how to install your 5-Port 1000BASE-T Gigabit Ethernet Switch, how to connect it to your Gigabit Ethernet network. Terms For simplicity, this documentation uses the terms “Switch” (first letter upper case) to refer to the 5-Port 1000BASE-T Gigabit Ethernet Switch, and “switch”... -
Page 7: Echnology
N T R O D U C T I O N This section describes the features of the 5-Port 1000BASE-T Gigabit Ethernet Switch, as well as providing some background information about Gigabit Ethernet and switching technology. Gigabit Ethernet Technology Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure, format, and support for CSMA/CD protocol, full duplex, flow control, and management objects, but with a tenfold increase in theoretical throughput over 100-Mbps Fast Ethernet and a... - Page 8 Features The 5-Port 1000BASE-T Gigabit Ethernet Switch was designed for easy installation and high performance in an environment where traffic on the network and the number of users increase continuously.
- Page 9 Support Full duplex transfer mode for 1000Mbps Full wire speed reception and transmission Store-and-Forward switching method Supports 8K absolute MAC addresses Supports 256KBytes RAM for data buffering Extensive front-panel diagnostic LEDs IEEE 802.3x flow control for full-duplex Back pressure flow control for half-duplex...
-
Page 11: Unpacking And Setup
Unpacking Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following items: One SGD5 5-Port 1000BASE-T Gigabit Ethernet Switch Four rubber feet with adhesive backing One external power adapter This User’s Guide If any item is found missing or damaged, please contact your local supplier for replacement. -
Page 12: Identifying External Components
D E N T I F Y I N G X T E R N A L O M P O N E N T S This chapter describes the front panel, rear panel and LED indicators of the Switch Front Panel The figure below shows the front panels of the switch. - Page 13 Power is supplied through an external AC power adapter. Check the technical specification section for information about the AC power input voltage. 1000BASE-T Ports: Five Gigabit Ethernet ports of 10/100/1000Mbps Auto-Negotiation interface. LED Indicators The LED indicators of the Switch include Power, Link/Act, 1000Mbps and 100Mbps.
-
Page 14: Technical Specifications
E C H N I C A L P E C I F I C A T I O N S General Standards: IEEE 802.3ab 1000BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3 10BASE-T IEEE 802.3x Flow Control Protocol: CSMA/CD Data Ethernet: 10Mbps (Half-duplex) Transfer... - Page 15 Physical and Environmental DC inputs: 7.5V 1.5A Power Consumption: 8.5 watts maximum Operating 0 °C ~ 40°C Temperature: Storage -10°C ~ 70°C Temperature: Humidity: 5% ~ 95% RH, non-condensing Dimensions: 171 x 98 x 29 mm (W x H x D) FCC Class A, CE Marking Class A, VCCI Certification: Class A...
-
Page 16: Limited Lifetime Warranty
Amer.com Warranty Policy Limited Lifetime Warranty In the event of a defect in quality or workmanship, Amer.com will repair or replace any hardware product sold by Amer.com with new or reconditioned parts free of charge in North America for a limited lifetime period unless otherwise specified on the sales invoice from the date of original purchase. - Page 17 Limits and Expectations There are no express warranties except as listed above. Network products by Amer.com shall not be liable for incidental or consequential damages resulting from the use of this product. Any future upgrades, including (but not limited to) hardware and software are not covered by this limited warranty. If a hardware problem with this product develops during the warranty period, you may contact the Amer.com Service Center at:...
Need help?
Do you have a question about the Gigabit Ethernet Switch and is the answer not in the manual?
Questions and answers