Table of Contents
Advertisement
Burners:
reinstall
orifice
one ofthe
spud
screws
screws homing
range cooktop
the burner head down. Lift the
burner head off the cooktop to uncover the
orifice spud homer. The orifice spud is recessed
in the holler.
Note: Reinstall one of the screws through the
range cooktop to hoM orifice spud homer in phce
wMb removing and rephcing orifice spuds.
Locate the LP. gas orifice spuds
in Uiterature package. Orifice
spuds are stamped with a
number and marked with two
cobr dots and a groove.
5116"
nut driver
_oove
L,P, gas
orifice spud
orifice
spud,
Replace orifice
spud with the
number listed
in chart,
LP. Gas
Surface
burner
Left rear
Left front
Right front
Right rear
Propane
Orifice
Color
Rate(BTU/hr} Number Marking
8,000
LS0
Green/Lt. Blue
11,000
L99
Green/Yellow
8,000
LS0
5,000
L65
Green/Brown
A brass orifice spud is located in the center of
each burner throat about 2" below the cooktop.
Apply masking tape to the end of a 5/16" nut
driver to fit snugly over the orifice spud. Press
driver down onto the spud of the left front burner
and remove by turning spud counter-clockwise
and lifting it out. Replace the Natural gas spud
with the appropriate LP. gas spud shown in the
table.
Continue to replace the remaining
orifice spuds,
one at a time. Placethe
Natural gas spuds in
plastic parts bag for future use and keep with
literature
package. Replace burner caps using
both screws, and burner grates.
orifice hood
Natural
gas
increase
gas
increase
flame
size
pre-set
at factory
for Natura_
gas
hood
LP, gas
decrease
gas
decrease
f_ame size
_mOven burner: Use 1/2" combination
wrench to turn the orifice hood down snug onto
pin (approximately 2 to 2-1/2 turns). DO NOT
OVERTIGHTEN. The burner flame cannot be
properly adjusted if this conversion is not made.
orifice hood
5u
Broil b urner: Use 1/2" combination wrench
to turn the orifice hood down snug onto pin
(approximately 2 to 2-1/2 turns}. DO NOT
OVERTtGHTEN. The burner flame cannot be
properly adjusted if this conversion is not made.
Page 8
6m
Reinstall the storage drawer. Complete
installation sections D through E, Pages 5-7.
Checking for proper cooktop burner and oven
flame is very important.
YOU MUST ADJUST "LOW" SETTING FOR
EACH COOKTOP BURNER. SEE STEP 1(;,
PAGE 6.
The small inner cone should have a very distinct
blue flame 1/4" to 1/2" long. The outer cone is not
as distinct as the inner cone. LP. gas flames may
have a slightly yellow tip. If the flame is noisy or
blowing, it is getting too much air. If the flame is
soft and lazy, it is not getting enough air.
Natural gas conversion
mComplete
installation
sections A-C (Pages
4-5} before converting
cooktop to natural gas.
Check that main gas supply line has been shut
off and the power suppty cord is disconnected.
pressure
_\
...... _
reguJator
_
--,
plastic
regulater
_
plastic
Cover
Natural
cap
--washer
--
Nat. gas
L,P. gas
DO NOT REFAOVE THE PRESSURE REGULATOR.
mPressureregulator: Remove storage
drawer and locate pressure regulator at back of
range. Remove plastic cover. Turn cap marked
"LP." on front of pressure regulator
counterclockwise with a wrench to remove. Do
Not disturb or remove the spring beneath the
cap. Turn the cap over and reinstall cap on
regulator so that the letter "N" is visible. Replace
plastic cover over cap.
S
reinstall
Surface
one of the
Burners:
or{rice
screws
Remove
burner
spud
_
\
spark electrode
screws holding
rangecooktop
the burner head down. Lift the
burner head off the cooktop to uncover the
orifice spud holder. The orifice spud is recessed
in the holder.
Note: Reinstall one of the screws through the
range cooktop to hold orifice spud holder in place
while removing and replacing orifice spuds.
Locate the Natural gas orifice spuds
in literature package. Orifice spuds
are stamped with a number and
marked with two color dots.
5/I6"
Natural
gas
nut driver
orifice
spud
orifice spud,
_.
Replace orifice
spud with the
number Jisted
in chart.
1__
burner
orifice
assembly
number
Natural Gas
Surface
burner
Left rear
Left front
Right rear
Natural Gas Orifice
Color
Rate(BTU/hrt Number
Marking
8,000
N139
Blue/Black
12,000
N176
Blue/Red
9,500
N151
Blue/Brass
5,000
N112
Blue/White
Locate the brass orifice spuds in the center of each
burner throat about 2" below the cooktop. Apply
masking tape to the end of a 5/16" nut driver to fit
snugly over the orifice spud. Press driver down
onto the spud of the left front burner and remove
by turning spud counter-clockwise and lifting it
out. Replace the LP. gas spud with the appropriate
Natural gas spud shown in the table.
Continue to replace the remaining orifice spuds,
one at a time. Place the Natural gas spuds in
plastic parts bag for future use and keep with
literature package. Replace burner caps, using
both screws and burner grates.
orifice hood
pin
/
hood
Natural
gas
increase
gas
_
LP, gas
increase
fJame size
decrease
gas
pro=set at factor',!
decrease
for Natural
gas
f_ame size
4R
Oven burner: Use 1/2" combination
wrench to loosen the orifice hood away from pin
(approximately 2 to 2-1/2 turns). The burner
flame cannot be properly adjusted if this
conversion is not made.
5_
Broil burner: Use 1/2" combination
wrench to loosen orifice hood away from pin
(approximately 2 to 2-1/2 turns), The burner
flame cannot be properly adjusted if this
conversion is not made.
the storage drawer. Complete
installation sections D through E, Pages 5-7.
Checking for proper cooktop burner and oven
flame is very important.
YOU FAUSTADJUST "LOW" SETTING FOR
EACH COOKTOP BURNER. SEE STEP 16, PAGE 6.
Natural gas flames do not have yellow tips.
Advertisement
Table of Contents
