Advertisement
}
J
Check that you
removed
all the shipping
pieces,-including
the round shipping
piece,
Dispose of all
materials
in proper
manner,
If you do not remove
the round shipping
piece,
your washer/dryer
may "walk"
away
from its location.
your tools,
Check that you have all
[] Turn on water faucets and
check for leaks, Tighten couplings if there is
leaking, DO NOT OVERTIGHTEN. Thiscould
cause damage to faucets,
2m
Replace
the access panel,
Be
sure to tighten
screws at each
end of the
access panel,
3
[] Plug power supply cord into
grounded outlet,
4_
Read the Use and Care Guide
to fully understand
your new washer/dryer,
Now start the washer and allow it to
complete
the regular cycle,
5
[] Remove tape
from dryer door
and open dryer door, Remove tape
across
the dryer lint screen, Check to be sure lint
screen is in its proper
position, Wipe out drum
with a damp
cloth to remove
any dust, Start
dryer and allow it to complete
a heat cycle
to make sure the dryer is working
properly,
Finally, save all literature
and
keep with washer/dryer,
Panel E
Recessed
and doset
installation
instructions
Fire Hazard
It is recommended
that thewasher/dryer
be
exhausted
to the outside,
If washer/dryer
is installed
in a closet,
the
dryer
MUST
be exhausted
outside.
Failure
to follow
these
instructions
may
result
in a fire.
To prevent large amounts
of lint and moisture
from accumulating
and to maintain
drying
efficiency,
and to prevent
exposure
to
possible
health hazards, this appliance
should be exhausted
outdoors.
THIS WASHER/DRYER
MAY BE INSTALLED
IN A RECESSED AREA OR CLOSET.
The installation
spacing
is in centimeters
and
inches and is the minimum
allowable,
Additional
spacing
should be considered
for
ease of installation,
servicing
and
compliance
with local codes and
ordinances,
If closet door is installed,
the minimum
unobstructed
air openings
in top and
bottom
are required,
Louvered
doors with
equivalent
air openings
are acceptable,
Closet installation
must be exhausted,
Other installations
must use the minimum
dimensions
indicated,
Recessed
installation
,__,m (o")
drye---T
©_
_©
washer
0 crn (0")
7.6 crn
(3")
___&
front view
side view
Minimum
installation
spacing
Note: If recessed installation is exhausted, all
spacing can be 0 cm (0 in).
Additional clearancefor wall, doorand floor
molding may be required.
Cbsef
installation
closet door
\
_
--___l_O_sq.
cm (48
in.)
sq.
7.6cm (3")
0
7.6 cm (3")
_f
_
_5_-sq.
crn (24 sq. in.)
"
_-
front view
Unobstructed air openings are minimum for closet
door. Louvered door with equivalent air openings
is acceptable.
310 sq. em (48 sq. in.)
?-
closet
door
155 sq. crn (24 sq. in.)
L
L2.5
cm (1")
side view
-_--- 0 cm (0")
Additional
space may
be needed
_rexhaust
Closet installation
must be exhausted
outdoors.
Recessed,
non-exhausted
installation must use
only the rear exhaust
position
and Exhaust
Deflector
Kit No. 4500 is required.
Product dimensions
(Shown with legs extended
1 inch from
bottom
of washer/dryer.)
61 cm
i<
"-I
31, 27
I_/-
11.Icm
(4-3/S")
recess
depth
recessw, th
\--
48.3 cm
(19")
rear view
70.2 cm
(27-5/8")
144.8 cm
(57")
119.4 cm
(47")
39.1 cm
130.
crr
:51-
2")
r y
v
T
S1.6 cm
(32 - 1/8")
!
side view
54.1
cm
(21-5/16")
__
69.2 cm
(27-1/4")
13.3crn
T
182.2 cm
(71-3/4")
96.5 cm
(38")
Advertisement
