Subscribe to Our Youtube Channel
Related Manuals for Fisher & Paykel DishDrawer DS602I
Summary of Contents for Fisher & Paykel DishDrawer DS602I
- Page 1 Fisher&Poykel DishDrawer DS602 (Prefinished) DS6021 (Integrated) Part No. 525854/B Models DS602 DS602I...
- Page 2 NOTE TO THE INSTALLER • Be sure to leave these instructions with the Customer. • Ensure this appliance is properly grounded. NOTE TO THE CONSUMER • Keep these Installation Instructions with your Use & Care Manual future reference. IMPORTANT • Read these Instructions completely and carefully.
- Page 3 Section General Information Preparation Product Specifications Cavity Dimensions Tools Needed to Install DishDrawer Product Parts- Prefinished Single Product Parts - Integrated Single Section Electrical, Plumbing & Drainage Information Electrical Grounding Instructions Plumbing - Water Supply Plumbing - Drainage Options Section Fitting the Single DishDrawer Single DishDrawer...
- Page 4 GENERAL INFORMATION Ensure the DishDrawer enclosure is prepared for installation. WARNING Remove all packaging and materials supplied with the DishDrawer. Before installing i )ishl "h awer. rem,-_\v lhe It vim h,rve any (lueslinns con(mnmg lhe inslallalion ol this Dishl)rawe_, _onna(:t II_ uit!_P',Ikol 22982 AlcaldeDrive...
- Page 5 IMPORTANT Where the DishDrawer J in an under counter i situat;on: i.e. huih into ,'! I kitchen 11i, unit, recommended that bare wood surrounding the DishDrawer is sealed with based paint or polyurethane to prevenl possible steam damage. IMPORTANT [ If mounting DishDrawer near the Ix)from of the cabinel,...
- Page 6 _, \ Foot Template - Single (1) Drain Hose Supporl (1) Screw (1) Wire Clip (1) M8 Boffs(4) Washer_ (4) Single Connector (t) Edge protector (1) Flexible Extrusion (3) 10. Soldertess Lug & Washer (1) 1T. Inlee Idose Washer (1) 12.
- Page 7 5. 1 _S. O • lemplate LSkn_ "l_ Drain _ose suppo_ {$) Screw (I) wi:e C_tip (.I i Single Conne_O_ (I) _oUntil_ BTacke_ Nuts _4) Bad_l_ Kit 12) _B Bolts (-I_ Washers L4'_ Seal&1) II, DoO(S_ews idle pioe_or (I) lexbl* I'xu sio_ 3) &Washer(l) "...
- Page 8 ELECTRtCAL, PLUMI ING & DRAINAGE INFORMATION WARNING Care should be exercised when lhe appliance is installed or removed, to reduce the likelihood of dalnagee Io lhe power supply cord. Impu)pel connection tile c_luipnlent-gronndin If lhe l×)wer supply cord is daulag(_l, it nlusl be replaced by tile Manufacturer.
- Page 9 WASTE WASTE DISPOSAL UNIT HOT WATER OishDrawer & Waste Disposal VALVt HO_ATER VALVE TO CONSTRAII_ING SURFACE D5602 Prefinished Model is shown. There is no variation P,JOle: plumbing belween DS602 Prefinished Model and DS6021 Integrated Mode|. Op'Uons 1 and 2 are the preferred option. Page DS_08...
- Page 10 FITTING SINGLE DISHDRAWER El_su_e the cavity is at • least 227/_'' deep. Draw tile cavity center line on the supporting cabinetry. IMPORTANT For Inlegraled pr(xtuct Center Template in cavity with door tilickness olhel using V-notch on the front than _!4", tile Template of lhe Template.
- Page 11 WARNING • P.nstlle the edges oI tilt, I ec_:l the Power Cord, Inh"l Hose. and Drain +io_o thzc)tl_,!i the Set,,4,.:e< II<fi_' l%sitior: [ • ih(" ])ish[j+av,,et it: front ot lho ni>nmr+g [ t_IIlSt !X: [_lh','t*,,i ,_i:h _:, ildg<_Frole+ ;o_ pro+i<ied Connect the Inlet Hose to tlu+ HOT WATER...
- Page 12 If required, trim the Single Connector to the size which matches the waste lee or air break to Ix, used. There are ribs provided to guide cutting. When using tile Single Connector, the hose should be pushed in firmly, 5 clicks. Remember to slip the Wire Clip over the Drain Hose belore connecting to the Single Connector.
- Page 13 &l I a I_aa a =h:( I :] 11 }'_ I _'i I Ll [|]_W;N I F;TN; h_I |_1 i Ill _'W_M_;_tj | i'a Flexible Extrusions are supplied to enable the installer to help fill any excess space between the sides ol lhe DishDrawer and the cavity.
- Page 14 INSERTING SINGLE DISHDRAWER INTO CAVITY WARNING DO NOT push against lhe middle of the drawer. DishDrawer Cabinet IMPORTANT Make sure the inlel and Align handle drain hose and main flex curve wIth I"_'_ are nol reslricled or cabinet front • 3/32"...
- Page 15 |NFORMATION FOR CABINET MAKER INTEGRATED DISHDRAWER !,'911I_]LI_I[,I Customer / Architect to Specify Control Badgo position Badge can [_e located anywhere within the Mounting Zone sho.,t Handle position will need to be taken into account. When mounting the handle ensure fastenings do not protrude beyond the back surfaceof the Drawer Front.
- Page 16 IMPORTANT Recommended Drawer Front ti_ickness for Irltegral_,J pro(|ll(:l V." to %". IMPORTANT A minirnum clearance of $/3/"must be maintained between the Drawer Front and existing cabinetry, except belween the underside of the Drawer Front and the shelf, where a '/d" i clearance is needed for I product venting.
- Page 17 IMPORTANT Width Measurements (Wl) All marking out 1o i_- done Measure Ihe width of the cavity at the top and the bofforn, using the smaller on the back suriac_. _,! :i_, of the measurenrenls, subtract V_d' (_/___" each side) clearance. This is the Drawer Frof'd width dilnension...
- Page 18 IMPORTANT A minimum clearance Option 1 and Option 2 show two different slyles of cabinetry. V2' is required between tile I.|llderSic/e Option 1 shows how to seal cabinetry below the DishDrawer by using a loarn seal provided in the accessories. Drawer [ rr)ll_ a_ld...
- Page 19 INTEGRATED DRAWER FRONT INSTALLATION There are several different colored Integrated badges to choose from. They include black, chrome, satin & brass. Two color options are provided with your rnachine, other optionsare available from your local Dealer. There are five parts 1othe Integrated Badge Assembly.
- Page 20 WARNING Care should Ix_ laken ill the following steps. • Remove Drawer Front Mounling Panel by CAUTION withdrawing pins from sides of drawers using Take care n<)t it) damage long nosed pliers. i front surfac:t-" o l panel. [nstlre all cuts are straight and cart +'is taken in a downwards a'nd to avoid damage to the...
- Page 21 • ] CAUTION The rubber seal belwe_l_ lhe Drawer and Drawel Front must be kept in _lace. WARNING Plug lhe grounding v, ire The Electr01;ics Board i_ onto the panel an eleclroslalic Se.nsiliv_" device. £nsure you are Connect badge wires to adequalely grounded integrated badge port on when connecting or...
- Page 22 FINAL FITTING FOR SINGLE DISHDRAWER Counter top • Check Hnal fit _I Dishl )m',vet m (1 _v I!_1 . Tighten M_ oolls. DishDrawer Shelf Page DS_21...
- Page 23 FINAL CHECKS Ensureproduct is level, securely fastened to lhe floor and opens and closesfreely. Ensure inlel hose to faucet (-onneclion is tightened to specification. Insure any knockouts or plugs in drain connection have lxeen dr ed out and dra n connection made to specification. Plug in and turn ON the power and water supply.
Need help?
Do you have a question about the DishDrawer DS602I and is the answer not in the manual?
Questions and answers