Download Print this page

Turning On The Appliance - Haier DW12-BFE Owner's Manual

Haier domestic dishwasher owner's manual
Hide thumbs

Advertisement

Turning on the Appliance

Starting a wash cycle
After having completed all of the installation steps in the preced-
ing paragraphs, turn on the water all the way and press the ON-
OFF button (A) located on the control panel. The "B" indicator
light will come on. At this point, the appliance is on but you must
wait a few seconds before programming the setting for the cycle.
Setting and Starting a wash Cycle
Select the desired cycle by pressing the selector button (G). Each
time the button is pressed, one of the "H" cycle indicator lights will
come on in succession. Choose the wash cycle you feel is most
appropriate for the type of dishes that need washing (consult the
wash cycle table contained in this manual, especially when first
using the appliance).
Press the Start/Pause button (I), and after a few seconds a short
acoustic sound will indicate that the wash cycle has begun and
can no longer be changed. If necessary, read the paragraph en-
titled" Cancelling or modifying a cycle while underway..."
Cancelling or modifying a cycle while underway
Premise : A cycle that is underway can only be modified if it has
only been running for a short time. Otherwise, the detergent may
have already been used, and the appliance mayhave already
drained the wash water. If this is the case, the detergent dis-
penser must be refilled (see the paragraph entitled, "Loading
the Detergent").
To modify a cycle that is already underway, press the ON-OFF
button (A), then all of the settings will be cancelled.
If you forget to load some of the dishes
The wash cycle can be interrupted by pressing the Start/Pause
button. You can then load additional dishes and turn the appli-
ance back on. The cycle will start where it left off.
Wash cycle Programme Light
The wash cycle is running and the cycle indicator light (H) for the
cycle will begin to blink.
At the end of the wash cycle
Six acoustic signal will indicate that the wash cycle has finished
and the cycle indicator light (H) for the cycle will begin to die out.
Turn off the appliance using the ON-OFF button. Turn off the
water supply to the appliance and open the door. Wait a few
minutes before unloading the dishwasher to avoid handling the
dishes and utensils while they are still hot and more susceptible
to breakage. They will also dry better.
GB
Setting the Wash Cycle with a Delayed Start Time
Premise: After selecting the wash cycle as indicated in the para-
graph entitled, "Setting and Starting a Wash Cycle..." the delay
time can be set.
By pressing the "E" button (see close-up view-'Control panel")
the start of wash cycle can be delayed for between 1 to 9 hours.
Each time the button is pressed, the display (F) will show the
number of hours for the delay period. Choose the amount of
time desired. When the appliance is started with "I" button, a short
acoustic signal will sound and the delay time on the display will
blink, indicating that the countdown has begun.
After the time has lapsed, the cycle will start.
a) During the delay period, it is preferable not to change any of
the settings. If it is necessary, all of the settings must be cancelled
by pressing the ON-OFF button (A) to indicate that all of the set-
tings have been cancelled.
At this point, all of the steps for "Setting the Wash Cycle with a
delayed Start Time" and "setting and Starting a Wash Cycle" must
be repeated, following the instructions contained in the correspond-
ing sections.
b) If the door is opened during the delay period, the indicator will
blink and acoustic signal will sound, and the countdown will stop.
It will begin again when the door is closed .
Wash Cycle adjustment Buttons
1/2 load Button
This button (see "close-up View - Control Panel", letter "C") make
it possible to wash dishes using only the upper rack if there are
not enough dishes for a full load. This will allow you to save on
water and eletrical energy. It can be used before setting any of
the wash cycles, except for the intensive cycle (if included in the
wash cycle table). Please keep in mind that the amount of deter-
gent should also be cut in half.
.6.
NOTE:

Advertisement

loading

  Also See for Haier DW12-BFE

  Related Manuals for Haier DW12-BFE

This manual is also suitable for:

Bfd60ss