Table of Contents
Advertisement
Quick Links
Installation instructions
for your new
Builto/n
Dishwasher
CAUTION:
o Before you begin--Read these instructions completely and earefully_
o IMPORTANT-Save these instructions fur local inspector's use,
= IMPORTANT-OBSERVEALL GOVERNING CODESAND ORDINANCES.
= Note to Installer-Be sure to leave these instructions with the Consumer.
• Note to Consumer-Keep these instructions with your Owners Manual for future reference,
If you received a damaged dishwasher,
you should immediatelycontact your
dealer or builder.
The dishwasher MUST be installed to allow for future removal
from the enclosure if service is required. Installation of this
dishwasher requires basic mechanical and electrical skills_
Proper installation is the responsibility of the installer.
[] Two Phillips head countertop mounting screws taped to dishwasher
Materials required:
[] 90° elbow
(3/8" NPT external thread on one end and
opposite end sized to fit water supply)
[] Thread seal tape
[] UL Listed Wire nuts (3)
Fornew installations only:
[] Air gap for drain hose, if required
[] Waste tee for house plumbing, if applicable
[] Electrical cable or power cord, if applicable
[] Screwtype hose clamps
[] Strain relief for electrical connection
[] Hand shut-off valve (recommended)
[] Water line 3/8" rain copper or t/2" rain plastic
[] Coupler for extending drain line, if applicable
Electrical Cable
or Power Cord
90° Elbow
ScrewType Clamps
ThreadSeal
StrainRelief
Tape
Wire Nuts
_
Air
_
Waste
@
_)
Gap
Tee
Coupler
'LotWater Line
®
Shut-Off
Valve
Toolsrequired:
[] Phillips head and flat blade screwdrivers
[] Adjustable wrench (6")
[] Level
[] Carpenters square
E) Measuring tape
[] Safety glasses
D Flashlight
Fornew installations only:
[] Tubing cutter
[] Drill and appropriate bits
O Hole saw set
SafetyGlasses
Adjustable
_h
Wrench
_'_ _/
Measuring Tape
!
Square
Level
Advertisement
Table of Contents
Related Manuals for Kenmore 36314673100
Summary of Contents for Kenmore 36314673100
- Page 1 Builto/n Installation instructions Dishwasher for your new CAUTION: o Before you begin--Read these instructions completely and earefully_ o IMPORTANT-Save these instructions fur local inspector's use, = IMPORTANT-OBSERVEALL GOVERNING CODESAND ORDINANCES. = Note to Installer-Be sure to leave these instructions with the Consumer. •...
-
Page 2: Drain Requirements
. The rough cabinet opening must have a minimum width and depth of 24",and approximately 34-1/2" high from floor to underside of the countertop Figure A • The back wall should be free of pipes or wires, Figure A This WallArea •... -
Page 3: Electrical Requirements
"// t'i- Alternate "__ WARNING FORPERSONALSAFETY: R EMOVEHOUSE Receptacle I FUSEOROPENCIRCUITBREAKERBEFORE BEGINNING INSTALLATION. DO NOT USEAN EXTENSIONCORDORADAPTER PLUG WITH THIS APPLIANCE,. ELECTRICALREQUIREMENTS: Cabinet o This appliance must be supplied with t20V, 60 Hz., and connected to an individual, properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse Groul... - Page 4 [ Step 4 access panel and ,oekick Do not remove the wood base until you are ready to install Remove the two screws below the access panel and set aside the dishwasher The dishwasher will tip over when the door for reuse.rRemove access panel by backing out the two is opened.
- Page 5 continued [step9 ,,.,..,,e, ,.,o o ob,.o, IStep ,.o..d Position the water supply line and house wiring en the floor of Slide the dishwasher into the opening a few inches at a time the opening to avoid interference with base of dishwasher As you proceed, pull the drain hose through the opening and and components under dishwasher.
-
Page 6: Drain Line Installation
continued IStep 13, co,.e='W.ter.uppUv Connect water supply line to 90° elbow installed in Step 6. Important: Whenopening and Open and close the door_Check to be sure door spring does Water Valve Bracket closing thedoor, t hedoor spring should not touch the fi[E not rub against fill hose or water supply line. - Page 7 continued ] Step15 Verify that power is turned off at source. If power cord is Locate the three dishwasher wires (white, black, and green) used, plug it into the wall outlet and go to Step 16 if dish- with the stripped ends Insert the three wires through the washer is to be directly wired to house wiring, continue with small hole in the junction box bracket Using wire nuts of this step...
- Page 8 !continued IStep18 Replace access panei and toekiCk Refer to Figure V1Place the toekick against the legs of the dishwasher, Align the access panel to the dishwasher and tighten the two access panel screws, Align the teekick and make sure the bottom edge is against the floor, Insert and tighten the two toekick attachment screws, making sure the Tighten 2 bottom edge of the toekick stays in contact with the floor,...