Related Manuals for PureLink PT-MA-HD88-C
Summary of Contents for PureLink PT-MA-HD88-C
- Page 1 8x8 HDMI™ Matrix Switcher with IR & 3D Support User’s Guide Model no. PT-MA-HD88-C Designed in Germany Made in Taiwan © 2010 PureLink GmbH. All rights reserved. www.purelink.de...
-
Page 2: Table Of Contents
Panel Descriptions ........................5 IR Pass-through ........................7 Installation ..........................8 EDID LEARNING ........................8 Section 2: Operation appoach ........................9 Section 3: Specifications ..........................19 Section 4: FAQ.............................. 20 Section 5: Notice ............................21 Section 6: Performance Guide ........................22 www.purelink.de... -
Page 3: Section 1: Getting Started
Please read all of these instructions carefully before you use the device. Save this manual for future reference. The PT-MA-HD88-C 8x8 HDMI™ Matrix Switcher with IR & 3D Support has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the PT-MA-HD88-C should be used with care. -
Page 4: Package Contents
Easy installation with rack-mounting and wall-mounting designs for master and receiver respectively — Fast response time – 2~5 seconds for channel switch Package Contents Before you start the installation of the switch, please check the package contents. — PT-MA-HD88-C — Matrix Receiver — Rack-mounting ear set —... -
Page 5: Panel Descriptions
Panel Descriptions FRONT PANEL — PT-MA-HD88-C, transmitting unit (TX) VFD window 2. Input Push Button: Front panel push buttons used to select the number of input source & LED display for input channels 3. Output Push Button: Front panel push buttons used to select the number of display channel & LED display for output ports 4. - Page 6 FRONT PANEL — PT-MA-HD88-C, receiving unit (RX) Signal Level: Adjust the 8-level equalization control to the received HDMI signals. The HDMI signal level varies from strongest (0) to weakest (7) for respective transmission length from longest possible range to short distance. Please adjust the signal level from strongest to weakest and stop turning the rotary switch whenever the audio/video is playing normally.
-
Page 7: Ir Pass-Through
IR BLASTER: IR control on individual display device IR RECEIVER: IR receiver connected here can receive all IR command signals from the IR remote controls of PT-MA-HD88-C and all other HDMI source devices. CAUTION! Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets. -
Page 8: Installation
— Connect IR blaster to the PT-MA-HD88-C and direct the IR blaster to point towards the built-in IR receiver of the HDMI source devices. — Connect the +12V 5A DC power supply to the PT-MA-HD88-C and +5V 2A DC power supply to the receivers —... -
Page 9: Section 2: Operation Appoach
After you select the desired mapping configuration number, the number will be twinkled. Then, press the SET button, the setting will be saved successfully. press LEFT( ← ) button to go back to pre-layer Preset Mapping Mode Pushing “Left (←)”button, and use DOWN (↓) button to enter the Preset Mapping Mode. www.purelink.de... - Page 10 2) Press UP(↑) and DOWN(↓) button to select which input will learn the EDID from EDID port 3) Press SET button to confirm; or press LEFT(←) button to go back to pre-layer 4) If confirmed, VFD will show SUCCEED or FAIL after learning www.purelink.de...
- Page 11 Preset output status SAVE Save current mapping mode PRESET Preset mapping mode DEFAULT EDID Begin default EDID selection LEARN EDID Begin EDID learning from one output CLEAR Clear the previous IR operation procedure TAKE Trigger the previous setting Reserved Reserved www.purelink.de...
- Page 12 From : 4 to IN:0 Input 3 OUT A~ D Ⅰ~VIII Take 3. Press number key “Ⅲ” to select Input 3 From : 4 to IN: 3 OUT A~ D Ⅰ~VIII Take 4.Press “TAKE” button From : 4 to IN:3 www.purelink.de...
- Page 13 3) Software size: 3 MB 4) Minimum RAM requirement: 256 MB FW/SW Version Button Firmware Update Button COM Port Selection Network Button Connection Status Mapping Button Connect/Disconnect Button Default Reset Button Power On/Off Button In/Out Switch Button EDID Button Mute Output Button www.purelink.de...
- Page 14 ” to change connection status Power On/Off Button Click this button to power on/off “ ” Power on status(Blue): Click this button to power off device(Standby Mode) “ ” Power off status(Red): Click this button to power on device www.purelink.de...
- Page 15 Load EDID File to Input Select Input Click “Load” button to select the EDID file Learn EDID From Display Select EDID Port Select Input Click “Learn” button to learn display EDID Create EDID File Click “Create” button to create EDID file www.purelink.de...
- Page 16 Click “Save EDID on Computer” to save the generated EDID as a file View EDID Content Select Input, or From File Click “View” button to read the EDID and analysis Click “Save As” to save the read EDID as a file on computer www.purelink.de...
- Page 17 Select “Ethernet” and then will be a pop-up windows Key in the device IP address to the pop-up windows Close the pop-up windows Click the connected button to connect 11. Mapping Button Save Mapping: Select Mapping(1-8) Click “Save” button to save current mapping www.purelink.de...
- Page 18 User can click the input number button to let all outputs select the same input Ex: All outputs select input 3 14. Mute Output Button Click the circle button to turn off output’s video and audio Ex: Mute Output 2 www.purelink.de...
-
Page 19: Section 3: Specifications
Section 3: Specifications Description Units Transmitting unit of PT-MA-HD88-C Receiving unit of PT-E-HD10 Unit Description Transmitter Receiver HDMI Compliance HDMI Deep Color & full 3D HDCP Compliance Video Bandwidth Single-link 225MHz [6.75Gbps] Supported Resolutions 480i / 480p / 720p / 1080i / 1080p60... -
Page 20: Section 4: Faq
1080p and 7.1ch or 1080p and stereo audio. It means when the user sets the matrix at 1080p and 7.1ch, the source will only play the content under this format. Therefore if the TV cannot decode 7.1ch audio, there is definitely no audio. www.purelink.de... -
Page 21: Section 5: Notice
7. If your HDMI display has multiple HDMI inputs, it is found that the first HDMI input [HDMI input #1] generally can produce better transmission performance among all HDMI inputs. 8. Additional IR remote controls and IR blasters can be purchased as optional accessories to control the HDMI sources located separately. www.purelink.de... -
Page 22: Section 6: Performance Guide
Type of CAT5/6 cable Shielding CAT5 CAT5e CAT6 Wiring Unshielded (UTP) Solid Shielded (STP) Unshielded (UTP) Stranded Shielded (STP) Termination Please use EIA/TIA-568-B termination (T568B) at any time www.purelink.de... - Page 23 www.purelink.de...
- Page 24 www.purelink.de...
Need help?
Do you have a question about the PT-MA-HD88-C and is the answer not in the manual?
Questions and answers