Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PureLink SX-8800
Summary of Contents for PureLink SX-8800
- Page 1 SX-8800 Seamless UHD Matrix USER MANUAL PureLink 220-10 State Route 208 Fair Lawn, NJ 07410 USA Tel: +1.201.488.3232 Fax: +1.201.621.6118 E-mail: sales@purelinkav.com For order support, please contact your local dealer. For technical support, please contact us at support@purelinkav.com.
- Page 2 ⚫ Do not expose this device to Rain, Moisture, and Dripping ⚫ Only use accessories specified by the manufacture ⚫ Unplug this device during Lightning Storms ⚫ Product specifications may be subject to technical upgrades without further notice SX-8800 User Manual Version 1.0...
-
Page 3: Table Of Contents
Appendix B: Query IP address info via Network ......................20 Appendix C: Set IP info via UART ..........................21 Appendix D: Set IP info via Network ..........................21 Appendix E: Set IP address on Windows 7 or XP ......................22 SX-8800 User Manual Version 1.0... - Page 4 Appendix G: Connect via network route /switch ......................25 Appendix H: Troubleshoot with Network control ......................25 Appendix I: Advanced routing switch .......................... 26 Appendix J: Change List ( VS V2 version ) ........................29 SX-8800 User Manual Version 1.0...
-
Page 5: Introduction
Introduction SX-8800 provides seamless switching of up to (8) HDMI 2.0 inputs and outputs and incorporates the latest technologies available on the market including HDR and HDCP 2.2 compliance. The SX-8800 matrix switchers also feature a built-in web page interface/software allowing convenient set-up, user access, control, and operation. -
Page 6: Rear Panel
HDMI input 1 data stream. If HDMI 1 audio source is selected with AUTO by PC TOOL, then will use the original embedded audio of input HDMI 1 as its audio data stream. SX-8800 User Manual Version 1.0... - Page 7 For example, if input HDMI m is routed to output HDMI n1 and n2 ports, then IR IN n1 and n2 ports will be routed to IR OUT m port. Please refer bellow illustration. Relationship between video and IR routing IR extender connectors (not as accessories) SX-8800 User Manual Version 1.0...
-
Page 8: Rs232/Lan Control
Port RS232-1 is DB9 female connector, Pins layout as bellow. User needs use the corresponding cable, directly/straight RS232 cable ndex Tx( Matrix → Rx( Matrix ←PC PC) PC ) Baud rate 9600 ⚫ RS232-2 and IR-EXT ports are reserved for future development Ethernet control and connection Note：Factory default network setting： SX-8800 User Manual Version 1.0... -
Page 9: Pc Tool User Guide
NOTE：In case of password lost, there’s a admin password to login and modify password: Smartsecuri@2010 Password modification 1. Click drop-down list to select account: Administrator or User 2. Input current password, then click the ‘modify’ button to authenticate 3. Input new password twice, then click the ‘modify’ button SX-8800 User Manual Version 1.0... -
Page 10: Connect With Pc Tool
Set IP address on Windows 7/XP, please refer to Appendix E User can directly connect via Ethernet cable (please refer to Appendix F ), Or connect via network route/switch (please refer to Appendix G ) SX-8800 User Manual Version 1.0... -
Page 11: Matrix Switch Page
Note:Save/Recall here button here works the same with front panel save/recall control System reset: The PC tool support reset system to recover to factory configuration. EDID Control: Click the ‘EDID’ button on Matrix Switch page, then opens a EDID control window SX-8800 User Manual Version 1.0... -
Page 12: Signal Setting Page
External: System will get the corresponding analog audio 2. Output type There are four options for input Output Type: UHD-HDMI (HDCP OFF): HDCP Off UHD-DVI UHD-HDCP-1.4, UHD-HDCP-2.2 3. Output Format User can set output resolution here 3840x2160@60 3840x2160@50 SX-8800 User Manual Version 1.0... -
Page 13: Finetune
User can read and set the brightness/contrast/saturation/sharpness of each output. NOTE： If none special occasions, do not change the default settings; If there is a problem after the change, click Reset to return to the factory settings. SX-8800 User Manual Version 1.0... -
Page 14: Video Wall
It means which output port connect to the display. ⚫ Output Format: Set the output resolution. Click to select the screen, then drag, select the screens to splice, right-click, and click Screen Stitching to splicing. SX-8800 User Manual Version 1.0... -
Page 15: Bezel Adjust
To cancel Video WALL, first select the wall which is splicing, right click, then select Cancel Stitching. Bezel adjust There are two options to set bezel Type A with pixels setting, maximum number is 255, see below: Type B with millimeter setting, see below: SX-8800 User Manual Version 1.0... -
Page 16: Multi Video Wall
Multi Video wall SX-8800 supports several Video walls at the same time, for example it supports one 2x2 wall and one 2x1 wall. Each wall has its own bezel setting. Click one wall and then set bezel one by one... -
Page 17: Multi View With Tv Wall
Screen 5 - Cancel Stitching, then select the same or another video source for screen 5 to display. This separate screen is a full display screen Save scene/ Load scene On the Video wall page, user can save or load one splicing wall scene, including input/output routing and wall layout SX-8800 User Manual Version 1.0... -
Page 18: Advanced Route Switch Page
3840x2160@60Hz, 3840x2160@50Hz, 3840x2160@30Hz, 3840x2160@25Hz, 1920x1200@60Hz,1920x1080@60Hz, 1920x1080@50Hz,1600x1200@60Hz, 1400x1050@60Hz,1366x768@60Hz, 1360x768@60Hz, 1280x1024@60Hz, 1280x768@60Hz, 1280x720@60Hz, 1280x720@50Hz, 1024x768@60Hz HDMI Amplitude T.M.D.S +/- 0.4Vpp Differential impedance 100±15ohm RS232/Ethernet control Baud rate and protocol Baud rate：9600, data bit：8， stop bit：1,no parity checking SX-8800 User Manual Version 1.0... -
Page 19: Package Contents
Method A: After connected to the device via UART, Click the ‘Find via UART’ button at ‘Matrix Switch’ page to read the IP information. Method B: After connected to the device via UART, Click the ‘Find via UART’ button at ‘Network Setting’ page to read the IP information. SX-8800 User Manual Version 1.0... -
Page 20: Appendix B: Query Ip Address Info Via Network
Method A: Switch to ‘Matrix Switch ’ page, then click ‘Search Device’ button to query IP address information. Method B: After switching to ‘Network Setting’ page, click ‘Search Device’ button to search devices, then click one device in the result list to load its IP address information. SX-8800 User Manual Version 1.0... -
Page 21: Appendix C: Set Ip Info Via Uart
Step B: Click the device you want to configure in the result list (When you click it, the software will read the network configuration of the device automatically) Step C: Modify the IP address or the IP address type or other configuration. Step D: Click the ‘Save Config’ button to save data SX-8800 User Manual Version 1.0... -
Page 22: Appendix E: Set Ip Address On Windows 7 Or Xp
Appendix E: Set IP address on Windows 7 or XP Windows 7: Open ‘Network and Sharing Center’: Modify static IP address:（e.g. 192.168.0.1）： Windows XP: Open ‘Network Connections: SX-8800 User Manual Version 1.0... - Page 23 Modify IP address of ‘Local Area Connection’:（e.g. 192.168.0.1）： SX-8800 User Manual Version 1.0...
-
Page 24: Appendix F: Direct Connect Via Ethernet Cable
After connected successfully, the button right to ‘Status’ will be ‘Connected’ (If you click it now, it will disconnect from the device) Note： The default IP address is 192.168.0.247，and the default subnet mask is 255.255.255.0 SX-8800 User Manual Version 1.0... -
Page 25: Appendix G: Connect Via Network Route /Switch
Solution A：Setting up the IP address type of the device to static mode or connecting the device to a network router which support HDCP function. Cause B：The device is not power on. Solution B：Please power on the device. SX-8800 User Manual Version 1.0... -
Page 26: Appendix I: Advanced Routing Switch
(the device connected to) does not support HDCP function. Appendix I: Advanced routing switch PC tool support automatically switch the input source periodically for the output port in order to facilitate the demonstration functions needed in some scenaries. Operation guide is as follows: SX-8800 User Manual Version 1.0... - Page 27 Press ‘Ctrl’ or ‘Shift’ first, then click to select input ports Click “ -->” button to add the input ports selected in step 2 . Check the output ports that need to automatically switch input source periodically. SX-8800 User Manual Version 1.0...
- Page 28 Send cmd only one loop：stop automatically switch when a loop is finished. Select all outputs：Quickly check or uncheck all output ports Click ‘Start’ button to start automatically periodically switch. SX-8800 User Manual Version 1.0...
-
Page 29: Appendix J: Change List ( Vs V2 Version )
Add Multi View function with Video wall Add another mode (Type B) to configure Bezel setting with TV wall Add separately Lock function with front buttons control Move Advanced routing switch section to Appendix I Change front POWER button action feature SX-8800 User Manual Version 1.0...
Need help?
Do you have a question about the SX-8800 and is the answer not in the manual?
Questions and answers