Qlogic iSR6142 Installation Manual
Intelligent storage router
Hide thumbs
Also See for iSR6142:
- User manual (172 pages) ,
- Installation manual (120 pages) ,
- Supplementary manual (3 pages)
Subscribe to Our Youtube Channel
Related Manuals for Qlogic iSR6142
Summary of Contents for Qlogic iSR6142
-
Page 1: Quick Start Guide
Quick Start Guide I N T E L L I G E N T S T O R A G E R O U T E R I N S T A L L A T I O N... - Page 2 Support Headquarters QLogic Corporation 4601 Dean Lakes Blvd Shakopee, MN 55379 QLogic Web Site www.qlogic.com Technical Support Web Site support.qlogic.com Technical Support Email support@qlogic.com Technical Training Email tech.training@qlogic.com North American Region Email support@qlogic.com Phone +1 952-932-4040 +1 952-687-2504 Europe, Middle East, and Africa Region Email emeasupport@qlogic.com...
-
Page 3: Suggested Configurations
Quick Start Guide The iSR6142 Intelligent Storage Router provides remote and local SAN island connectivity. The major applications are: ❑ Remote Data Replications between Fibre Channel (FC) storage arrays ❑ Connecting remote FC Servers to local FC storage ❑ Connecting iSCSI Storage to FC storage area network (SAN) ❑... -
Page 4: Installation Instructions
Installation Instructions This Quick Start Guide describes how to install and configure your new QLogic router by following these steps: ❑ Step 1. Verify the package contents. ❑ Step 2. Complete the pre-installation checklist. ❑ Step 3. Mount the router. -
Page 5: Step 3. Mount The Router
Figure 3. iSR6142 Ports and LEDs Attach the AC power cord to the iSR6142 Router and then to the wall outlet or power strip. Verify that the router’s input power LED is illuminated. The iSR6142 Router first runs its self-test, which takes about one minute, then begins normal operation. -
Page 6: Step 6. Install The Sansurfer Router Manager
1 and subnet mask is 255.0.0.0. From the workstation, open a command window and using a telnet session connect to iSR6142 using IP address 10.0.0.1. Login as “guest” and use the password “password.” This will take you to a CLI prompt... -
Page 7: Step 8. Run The Configuration Wizard
FC 2 WWPN If you have an NTP server, enable the NTP Server option and enter the NTP Server information. This is on the Information tab that displays when you select the iSR6142 router in the system tree view. ❑... - Page 8 At least one FC Port of the iSR6142 should be connected to a FC SAN. ❑ It is recommended to use Fibre Channel World Wide Port name (WWPN) based zoning. Add each iSR6142 router’s FC WWPN to all zones in the FC switch to which it is connected. The FC switch zoning changes allow the iSR6142 router to discover all devices in the FC SAN.
- Page 9 Congratulations! You have now successfully installed your QLogic iSR6142s and mapped the FC devices from remote SAN to local SAN. Refer to "Performance Tuning" in the iSR6142 Intelligent Storage Router Installation Guide for optimal parameter settings. Step 10. Configure iSR6142s for Connecting FC/iSCSI Initiators to...
-
Page 10: Troubleshooting And Technical Support
For technical support, visit our web site, support.qlogic.com, email us at support@qlogic.com, or call 952-932-4040. Warranty The QLogic iSR6142 Router comes with a standard one-year QLogic warranty, or as specified by other agreements. Please check the QLogic Web site at www.qlogic.com... - Page 11 QLogic Corporation. All other brands and product names are trademarks or registered trademarks of their respective owners. Information supplied by QLogic is believed to be accurate and reliable. QLogic Corporation assumes no responsibility for any errors in this brochure. QLogic Corporation reserves the right, without notice, to makes changes in product design or specifications.
- Page 12 *SN0054544-00 B* QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 949.389.6000 www.qlogic.com SN0054544-00 B...
Need help?
Do you have a question about the iSR6142 and is the answer not in the manual?
Questions and answers