Advertisement
Quick Links
TURBINE POWERHEAD
FOR
P/N 7160, 7161 & T210
These Turbine Powerheads have been carefully designed and manufactured for long life, reliable performance
and convenient cleaning. They are designed to do most of the cleaning work for you. They move easily and do
not require downward pressure for thorough cleaning.
As with any tool with moving parts, caution must be exercised while using these Turbine Powerheads. Please
read and save this Instruction Manual.
1. Keep hair, hands and feet away from rotating brush while the Turbine Power Head is running.
2. Remember that Turbine Powerheads operate whenever they are connected to a running vacuum. If children
are present, make sure to turn vacuum system off when leaving Powerhead unit unattended.
3. Do not attempt to service or unclog tool while unit is running.
4. Avoid picking up water or spilled liquids with a Turbine Powerhead. The vacuum system is designed for dry
pick-up only.
INSTRUCTION MANUAL
SAFETY PRECAUTIONS
Page 1
HAND HELD
TURBINE
POWERHEAD
FOR
P/N 6970g, 6971g
& 6972g
Advertisement
Related Manuals for H-P Products TURBINE POWERHEAD and HAND HELD TURBINE POWERHEAD
Summary of Contents for H-P Products TURBINE POWERHEAD and HAND HELD TURBINE POWERHEAD
-
Page 1: Instruction Manual
INSTRUCTION MANUAL TURBINE POWERHEAD P/N 7160, 7161 & T210 These Turbine Powerheads have been carefully designed and manufactured for long life, reliable performance and convenient cleaning. They are designed to do most of the cleaning work for you. They move easily and do not require downward pressure for thorough cleaning. - Page 2 INSTRUCTIONS FOR TURBINE POWERHEAD (A) ATTACHING THE TURBINE POWERHEAD To attach your metal wand, simply twist into Powerhead elbow until it fits snugly. The built-in, locking mechanism will prevent the wand from coming loose from your Powerhead while in use. To detach wand, depress tab on side of elbow and twist wand free.
- Page 3 (E) REMOVING THE DRIVE BELT AND BRUSH “It is recommended this procedure be performed by a Qualified Service Technician.” Should the drive belt or brush become clogged with debris or need replacing: 1. Turn off vacuum system and disconnect powerhead. 2.
- Page 4 Page 4...
- Page 5 INSTRUCTIONS FOR HAND HELD TURBINE POWERHEAD (A) ATTACHING THE HAND HELD TURBINE POWERHEAD To attach your metal wand and/or curved hose handle simply twist into hand brush neck until it fits snugly. (See Fig. 1). To detach wand or curved hose handle, simply hold neck of Hand Held Powerhead and pull apart with a twisting motion.
- Page 6 (E) BELT REPLACEMENT Remove brown base plate and belt cover (right side of Powerhead) by removing screw. (See Fig. 4). Next, remove belt from pulley (may help to turn cleaning brush backwards slightly.) (See Fig. 5). Pull belt and brush assembly out and replace belt. Before replacing base plate and belt cover, make sure a “2” is showing at both ends of brush assembly (this number is stamped right on the bearing housing.) (See Fig.
-
Page 7: Limited Warranty
Seller’s instructions, will be free from defects in materials and workman- ship for a period of one year from the date of the initial consumer purchase. H-P PRODUCTS, INC. warrants that the turbine powerhead or the hand held turbine powerhead, when used in a commercial application pur- suant to Seller’s instructions, will be free from defects in materials and workmanship for a period of ninety (90) - Page 8 Turbine Powerhead Item Part Description Lower Housing Wheel (2) SA Turbine Belt Cover Base Plate Compr. Spring Washer Washer, Elbow Seal Elbow Spring, Wand Retainer/Cap Spring, Latch SA Tophousing Bumper Seal (Large) Seal (Small) SA Brush T Latch (2) Belt Screw Base (3) O-Ring Screw (9)
- Page 9 Page 9...
- Page 10 HAND HELD TURBINE POWERHEAD Item No. Description Swivel Sub Assembly Turbine and Shaft Belt Swivel Seal (2 req.) Latch Spring Latch Housing, Assy. Half Label Slide Valve Sub Assy. Housing, Half/Belt Side Belt Cover Screw 6-19x.750 (3 req.) Brush Assembly Base Plate with Basket and Bumper Basket (Avail.
Need help?
Do you have a question about the TURBINE POWERHEAD and HAND HELD TURBINE POWERHEAD and is the answer not in the manual?
Questions and answers