Related Manuals for H-P Products Electric Powerhead Electroglide
Summary of Contents for H-P Products Electric Powerhead Electroglide
- Page 1 ™ ELECTROGLIDE ELECTRIC POWERHEAD OWNER’S MANUAL Review this manual before operating your Electroglide Electric Powerhead...
-
Page 2: Table Of Contents
Wand Assembly Attachments Performance Features Edge Cleaner Overload Protector Suction Control Maintenance and Care Light Bulb Replacement Cleaning the Brush Assembly Belt Removal and Replacement Brush Replacement Replacement Parts Limited Warranty Service Information ©Copyright 2000 H-P Products, Inc. Page 9-11 12-13... -
Page 3: Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this vacuum system. When using an electrical appliance, basic precautions should always be followed, including the following: To reduce the risk of fire, electrical shock or injury: · Unplug and disconnect power before servicing. -
Page 4: Parts And Features
ELECTROGLIDE PARTS AND FEATURES It is important to know your Electroglide parts and features to assure its proper and safe use. Review these before using your Electroglide. Wand Easy Release Pedal ELECTROGLIDE Model/Serial Numbers (On Bottom) Handle Release Pedal Always unplug the Electroglide before cleaning the brush area as brush may suddenly restart. -
Page 5: Assembling Vacuum System
ASSEMBLING VACUUM SYSTEM Before assembling your Electroglide Electric Powerhead, be sure you have all parts shown in PARTS AND FEATURES. Do not plug into electrical supply until assembly is complete. Failure to do so could result in electrical shock or injury. Hose Handle Suction... -
Page 6: General Operation
ELECTROGLIDE GENERAL OPERATION Handle Release Pedal ELECTROGLIDE ATTACHMENTS Hose Handle Attachments If the Electroglide is attached, turn cleaner OFF before removing hose handle from wands. 1. Press lock button, then pull to remove handle from wand. 2. Slide attachments firmly on handle as needed. Wand Assembly Attachments To remove wands from the Electroglide Powerhead, lock wands in straight up... -
Page 7: Performance Features
PERFORMANCE FEATURES Edge Cleaner Active brush edge cleaners are on both sides of the Electroglide. Therefore, guide either side of the Electroglide along baseboards or next to furniture to help remove dirt trapped at carpet edges. Overload Protector The Electroglide has built-in protection against motor and belt damage should the brush jam. -
Page 8: Maintenance And Care
ELECTROGLIDE MAINTENANCE AND CARE Always unplug electrical cord and vacuum hose before servicing and maintaining the Electroglide Electric Powerhead. Failure to do so could result in electrical shock or personal injury from cleaner suddenly starting. Always follow all safety precautions specified when caring Light Bulb Replacemnent 1. -
Page 9: Belt Removal And Replacement
MAINTENANCE AND CARE Belt Removal and Replacement The belt should also be checked periodically to be sure it is in good condition. It should be replaced if it is stretched, cracked or broken. If the belt needs replaced, use only Electroglide Belt # 7960. To remove belt: 1. - Page 10 ELECTROGLIDE MAINTENANCE AND CARE Belt Removal (continued) 6. Remove worn belt. 7. Slide brush supports off to check and clean brush support areas. To replace belt: 1. Slide washers and brush supports onto brush assembly. 2. Install new belt over motor drive, then over brush sprocket.
-
Page 11: Belt Replacement
MAINTENANCE AND CARE Belt Replacement 5. Tilt cover to back. Press cover firmly until side tabs snap into place. Replace cover screws, light bulb and light cover. Brush Replacement 1. Remove the Electroglide Powerhead cover, belt and brush assembly. 2. Remove brush supports, washers, screws, end brush, and brush sprocket pieces from ends of brush assembly. -
Page 12: Replacement Parts
ELECTROGLIDE ELECTROGLIDE REPLACEMENT PARTS... - Page 13 REPLACEMENT PARTS Illus. Part Description 7922 Wand (Upper) 7923 Wand (Lower) 7972 Cover, Power Head 7925 Screw 8-18 x 1-7/8 (2) 7926 Nozzle Housing 7927 Bumper 7967 Bulb, Light (15 Watt) 7965 Socket, Bulb 7929 Swivel 7930 Swivel Seal (2) 7931 Pad, Foot Pedal 7932...
-
Page 14: Limited Warranty
Seller’s instructions, will be free from defects in materials and workmanship for a period of ninety (90) days from the date of the initial sale by H-P PRODUCTS, INC. This warranty is limited to the replacement of defective parts and any costs of shipping shall be incurred by the purchaser. -
Page 15: Service Information
SERVICE INFORMATION The instructions in this booklet serve as a guide to routine maintenance. If additional service or repairs are required, please call 1-800-822-8356 for your nearest authorized service dealer. H-P PRODUCTS, INC. 512 W. GORGAS STREET LOUISVILLE, OHIO 44641... - Page 16 ® H-P Products, Inc. 512 W. Gorgas Street Louisville, Ohio 44641-0912 HVS-968-NL 02/02...
Need help?
Do you have a question about the Electric Powerhead Electroglide and is the answer not in the manual?
Questions and answers