Technical Specifications - Tannoy VXP SERIES Operation Manual

11. Technical Specifications

11. Technical Specifications
Following are the VXP Series technical specifications. These figures are accurate at the time of printing but please note that all figures are
subject to change without notice.
Model
Peformance
Frequency Response (-3 dB)
Frequency Range (-10 dB)
Frequency Response (-3 dB)
Frequency Range (-10 dB)
Dispersion (-6 dB)
Driver Complement
Crossover
Directivity Factor (Q)
Directivity Index (DI)
Rated Maximum SPL
2
Distortion
10% Full Power (8.94 V)
250 Hz
1 kHz
10 kHz
1% Full Power (2.83 V)
250 Hz
1 kHz
10 kHz
Construction
Enclosure
Finish
Connectors
Controls & Indicators
Fittings
Dimensions
Net Weight
Shipped Weight
Electronics
Maximum signal input for clip
Dynamic Range
Amplifier efficiency
Damping Factor
Distortion
Input Impedance
Protection systems
Over Current
Clip limiter
Temperature
Brownout
Mains
Indicators
Amplifier Type
PSU Specifications
Input Connector
Voltage Selection
Type
Efficiency
Input voltage
Mains fuse
Fuse type
Other features
StandBy power consumtion
Idle power consumption
Maximum power consumtion
1. Average over stated bandwidth. Measured at 1 metre on axis.
2. Unweighted pink noise input, measured at 1 metre in an anechoic chamber
A full range of measurements, performance data, and Ease™ Data can be downloaded from www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications,
which Tannoy reserves the right to alter without prior notification.
20
VXP Series Operation Manual rev 1.0.2
VXP 6
Full range mode 88 Hz - 35 kHz
1
Full range mode 80 Hz - 45 kHz
1
Hi-Pass mode 120 Hz - 35 kHz
1
Hi-Pass mode 100 Hz - 45 kHz
1
90 degrees conical
1 x 150 mm (6.00") constant directivity Dual Concentric™
Passive 1.6 kHz with dynamic HF protection
5.6 averaged 1 kHz to 10 kHz
7.0 averaged 1 kHz to 10 kHz
112 dB (average), 118 dB (peak)
2nd Harmonic 3rd Harmonic
2.64% 0.365%
0.223% 0.458%
1.873% 0.29%
2nd Harmonic 3rd Harmonic
0.64% 0.314%
0.062% 0.436%
0.78% 0.266%
6.44 litre, 12 mm (0.59") birch plywood, vented and internally braced
Textured black or white paint, with custom colours on request.
Powder coated perforated steel grille, Airnet cloth behind
1 x female XLR (input), 1 male XLR (link), 1 x Neutrik Powercon
Level Control
Power LED (Blue)
Signal LED (Red/Green)
Limit/Protect LED (Red)
Full Range / HighPass Switch (110 Hz)
Power Mode Switch
Power Switch
2 x M6 yoke bracket inserts, Blanking plate for optional VTH pole mount
333 x 225 x 215 mm (HxWxD), 13.1 x 8.9 x 8.1" (HxWxD)
7.0 kg (15.4lbs)
15.5 kg (34.2 lbs)
Input attenuator at Maximum: +4.5 dBu, (Hard clip will occur at +14.5 dBu input signal)
106 dB
>90%
>400 ref 8 ohms at 1 kHz
<0.05% @ 1 kHz -3 dB output (22 kHz bandwidth)
10 kohms unbalanced, 20 kohms balanced
Output current limiter, always active
Output voltage clip limiter, always active
Over temperature causes protective mute
Automatic protection & recovery
Inrush current limiter
1x Power LED, 1x signal LED, 1x Limit LED,
(Power LED: Red = StandBy, Green = On, Amber = Temperature protection active)
Inherently bridged, globally modulated, high performance single channel class D
Locking Neutrik Powercon
Universal mains input
High efficiency, regulated switch mode power supply
>85% typical
100 Vac-240 Vac +/- 10%, 50-60 Hz +/-10%
Internal
3,15AT
Inrush current limiter
<1 W
<15 W
250 W