Sharp MD-X5H Service Manual page 27

e) TEMP setting
Step No. Setting Method
Step 1 Testmode STOP state
Step 2 Press the CD PLAY button seven times. EEPROM setting menu
Step 3 Press once the MD PLAY button. Focus setting menu
Step 4 Press the CD PLAY button four times.
Step 5 Press once the MD PLAY button. TEMP reference value setting
Step No. Setting Method
Step 1 EJECT state (or mechanism-less state)
Step 2 Press the CD
• : Setting volue,
• If the VOL UP button is pressed while the specific setting item is indicated, the setting increases, and the new setting is set in LSI.
• If the VOL DOWN button is pressed while the specific setting item is indicated, the setting decreases, and the new setting is set in LSI.
• If the VOL UP/VOL DOWN button is held down, the setting changes continuously with 100 ms cycle.
f) CONTROL setting
Setting Method
Step No.
Step 1 Testmode STOP state
Step 2 Press the CD PLAY button seven times. EEPROM setting menu
Step 3 Press once the MD PLAY button. Focus setting menu
Step 4 Press the CD PLAY button five times.
Step 5 Press once the MD PLAY button. CONTROL 1 setting
Step 6 Press once the CD PLAY button. CONTROL 2 setting
Step 7 Press once the CD PLAY button. Setting of spin kick level in MOVE state
Step 8 Press once the CD PLAY button. Setting of readjustment interval time (minutes)
Step 9 Press once the CD PLAY button. Setting of equalizer coefficients A and D (high reflection)
Step 10 Press once the CD PLAY button. Setting of equalizer coefficients A and D (low reflection pit)
Step 11 Press once the CD PLAY button. Setting of equalizer coefficients A and D (low reflection groove) [ G D E Q A D_ _
Step 12 Press once the CD PLAY button. Setting of equalizer coefficients B and C (high reflection)
Step 13 Press once the CD PLAY button. Setting of equalizer coefficients B and C (low reflection pit)
Step 14 Press once the CD PLAY button. Setting of equalizer coefficients B and C (low reflection groove) [ G D E Q B C_ _
Step 15 Press once the CD PLAY button. Setting of autolevel slicer gain (high reflection)
Step 16 Press once the CD PLAY button. Setting of autolevel slicer gain (low reflection pit)
Step 17 Press once the CD PLAY button. Setting of autolevel slicer gain (low reflection groove)
Step 18 Press once the CD PLAY button. Setting of autolevel slicer offset (high reflection)
Step 19 Press once the CD PLAY button. Setting of autolevel slicer offset (low reflection pit)
Step 20 Press once the CD PLAY button. Setting of autolevel slicer offset (low reflection groove)
Step No. Setting Method
Step 1 EJECT state (or mechanism-less state)
Step 2 Press the TRACK EDIT button.
Step 3 Press once the CD PLAY button. CONTROL 2 setting
• : Setting volue
• If the VOL UP button is pressed while the specific setting item is indicated, the setting increases, and the new setting is set in LSI.
• If the VOL DOWN button is pressed while the specific setting item is indicated, the setting decreases, and the new setting is set in LSI.
• If the VOL UP/VOL DOWN button is held down, the setting changes continuously with 100 ms cycle.
• CONTROL 1
Pit 7 : High frequency superposition ON/OFF in record mode (0:OFF, 1:ON)
Pit 6~4 : Play start SD number (30 to 100 sector, 10 sector step)
Pit 2~0 : High speed jump over-run (384 to 830 lines, 64 lines step)
• CONTROL 2
Pit 4~0 : EEPROM version (a~)
TEMP setting menu
MD EDIT button. TEMP reference value setting
:
Measurement value
CONTROL setting menu
CONTROL 1 setting
Remarks
Remarks
Remarks
Remarks
– 27 –
MD-X5H/CP-X5H
Display
[ t s m e ]
[E E P R O M _ S E T]
[ _ _ F o c u s _ _ _ ]
[ _ _ _ T e m p _ _ _ ]
[ T E M P _ _ ]
Display
[ _ _ E J E C T _ _ _ ]
[ T E M P _ _ ]
Display
[ t s m e ]
[E E P R O M _ S E T]
[ _ _ F o c u s _ _ _ ]
[ _ C o n t r o l _ _ ]
[ C O N T R L 1_ ]
[ C O N T R L 2_ ]
[ S P K L E V m_ ]
[ A D J T T M_ _ ]
[ H D E Q A D_ _ ]
[ L D E Q A D_ _ ]
]
[ H D E Q B C_ _ ]
[ L D E Q B C_ _ ]
]
[ H A L S G_ _ _ ]
[ L A L S G_ _ _ ]
[ G A L S G _ _ ]
[ H A L S O F_ _ ]
[ L A L S O F S _ _ ]
[ G A L S O F S _ _ ]
Display
[ _ _ E J E C T _ _ _ ]
[ C O N T R L 1_ ]
[ C O N T R L 2_ ]