Sharp MD-X5H Service Manual page 25

Setting Method
Step No.
Step 9 Press once the CD PLAY button. Comparison level setting in case of FOK generation
Step 10 Press once the CD PLAY button. LPF coefficient setting (normal) in case of FOK generation
Step 11 Press once the CD PLAY button. LPF coefficient setting in case of FOK generation
Step 12 Press once the CD PLAY button. Waiting time setting in case of auto-focus retraction
• : Setting volue
• Pressing the REC button causes reversing.
• If the VOL UP button is pressed while the specific setting item is indicated, the setting increases, and the new setting is set in LSI.
• If the VOL DOWN button is pressed while the specific setting item is indicated, the setting decreases, and the new setting is set in LSI.
• If the VOL UP/VOL DOWN button is held down, the setting changes continuously with 100 ms cycle.
b) Spindle setting
Step No. Setting Method
Step 1 Testmode STOP state
Step 2 Press the CD PLAY button seven times. EEPROM setting menu
Step 3 Press once the MD PLAY button. Focus setting menu
Step 4 Press once the CD PLAY button. Spindle setting menu
Step 5 Press once the MD PLAY button. Spindle system loop filter gain constant setting
Step 6 Press once the CD PLAY button. Spindle system loop filter gain constant setting
Step 7 Press once the CD PLAY button. Spindle system loop filter gain constant setting
Step 8 Press once the CD PLAY button. Spindle system loop filter gain constant setting
Step 9 Press once the CD PLAY button. Spindle system loop filter f characteristic constant 1 setting
Step 10 Press once the CD PLAY button. Spindle system loop filter f characteristic constant 2 setting
Step 11 Press once the CD PLAY button. Spindle system loop filter f characteristic constant 3 setting
Step 12 Press once the CD PLAY button. Spindle system loop filter f characteristic constant 4 setting
Step 13 Press once the CD PLAY button. Spindle system loop filter f characteristic constant 5 setting
Step 14 Press once the CD PLAY button. Spindle drive output limitter setting
• : Setting volue
• Pressing the REC button causes reversing.
• If the VOL UP button is pressed while the specific setting item is indicated, the setting increases, and the new setting is set in LSI.
• If the VOL DOWN button is pressed while the specific setting item is indicated, the setting decreases, and the new setting is set in LSI.
• If the VOL UP/VOL DOWN button is held down, the setting changes continuously with 100 ms cycle.
c) Tracking setting
Setting Method
Step No.
Step 1 Testmode STOP state
Step 2 Press the CD PLAY button seven times. EEPROM setting menu
Step 3 Press once the MD PLAY button. Focus setting menu
Step 4 Press the CD PLAY button two times. Tracking setting menu
Step 5 Press once the MD PLAY button. Tracking system loop filter gain constant setting
Step 6 Press once the CD PLAY button. Spindle system loop filter f characteristic constant 1 setting
Step 7 Press once the CD PLAY button. Spindle system loop filter f characteristic constant 2 setting
Step 8 Press once the CD PLAY button. Setting of tracking system servo mode 4
Step 9 Press once the CD PLAY button. Tracking deceleration pulse level setting (for one line jump)
Step 10 Press once the CD PLAY button. Tracking deceleration pulse level setting (for 10 line jump)
Step 11 Press once the CD PLAY button. Tracking kick pulse level setting (for one line jump)
Step 12 Press once the CD PLAY button. Tracking kick pulse level setting (for 10 line jump)
Step 13 Press once the CD PLAY button. Tracking drive pulse width setting (for one line jump)
Step 14 Press once the CD PLAY button. Tracking drive pulse width setting (for 10 line jump)
Step 15 Press once the CD PLAY button. Tracking slip stop time setting (for one line jump)
Step 16 Press once the CD PLAY button. Tracking slip stop time setting (for 10 line jump)
Step 17 Press once the CD PLAY button. Tracking slip stop time setting (move)
Remarks
(when focus is "ON")
(when focus is "ON")
Remarks
(Until tracking servo ON)
(After tracking servo ON, inner periphery)
(After tracking servo ON, center)
(After tracking servo ON, outside periphery)
Remarks
– 25 –
MD-X5H/CP-X5H
Display
[ F O K L E V f _ ]
[ F O K L P F n _ ]
[ F O K L P F f _ ]
[ W A I T f_ _ _ ]
Display
[ t s m e ]
[E E P R O M _ S E T]
[ _ _ F o c u s _ _ _ ]
[ _ S p i n d l e _ _ ]
[ S P G _ _ _ _ _ ]
[ S P G _ i n _ _ ]
[ S P G _ m i d _ ]
[ S P G _ o u t _ ]
[ S P 1 _ _ _ _ _ ]
[ S P 2 _ _ _ _ _ ]
[ S P 3 _ _ _ _ _ ]
[ S P 4 _ _ _ _ _ ]
[ S P 5 _ _ _ _ _ ]
[ S P D L I M _ _ ]
Display
[ t s m e ]
[E E P R O M _ S E T]
[ _ _ F o c u s _ _ _ ]
[ _ T r a c k i n g _ ]
[ T G _ _ _ _ _ _ ]
[ T F 1 _ _ _ _ _ ]
[ T F 2 _ _ _ _ _ ]
[ S V C N T 4 _ _ ]
[ T R B L V 0 _ _ ]
[ T R B L V t _ _ ]
[ T R K L V 0 _ _ ]
[ T R K L V t _ _ ]
[ T D P W o _ _ _ ]
[ T D P W t _ _ ]
[ S L C T 0 _ _ _ ]
[ S L C T t _ _ _ ]
[ S L C T m _ _ ]