Cisco PA-5EFL= Installation And Configuration Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Adapter
  5. PA-5EFL=
  6. Installation and configuration manual
Cisco PA-5EFL= Installation And Configuration Manual

Cisco PA-5EFL= Installation And Configuration Manual

Ethernet 10base-fl port adapter
Hide thumbs Also See for PA-5EFL=:
Table of Contents

Advertisement

Quick Links

Download this manual
PA-5EFL Ethernet 10Base-FL Port Adapter
Installation and Configuration
Product Number: PA-5EFL(=)
Platforms Supported: Cisco 7100 Series Routers, Cisco 7200 Series Routers,
Cisco uBR7200 Universal Broadband Routers, Cisco 7301 Router, VIP2 in the
Cisco 7000 Series Routers and Cisco 7500 Series Routers
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Text Part Number: OL-3495-02

Advertisement

Table of Contents
loading

Related Manuals for Cisco PA-5EFL=

Summary of Contents for Cisco PA-5EFL=

  • Page 1 Installation and Configuration Product Number: PA-5EFL(=) Platforms Supported: Cisco 7100 Series Routers, Cisco 7200 Series Routers, Cisco uBR7200 Universal Broadband Routers, Cisco 7301 Router, VIP2 in the Cisco 7000 Series Routers and Cisco 7500 Series Routers Corporate Headquarters Cisco Systems, Inc.
  • Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...

  • Page 3: Table Of Contents

    LEDs Cables and Connectors Port Adapter Slot Locations on the Supported Platforms Cisco 7100 Series Routers Slot Numbering Cisco 7200 Series and Cisco uBR7200 Series Routers Slot Numbering Cisco 7301 Router Slot Numbering VIP Slot Numbering Identifying Interface Addresses Cisco 7100 Series Routers Interface Addresses...
  • Page 4 Using the show version or show hardware Commands Using the show diag Command 4-12 Using the show interfaces Command 4-14 Using the ping Command to Verify Network Connectivity 4-19 Using loopback Commands 4-19 PA-5EFL Ethernet 10BaseT-FL Port Adapter Installation and Configuration OL-3495-02...

  • Page 5: Preface

    Cisco 7301 router—consisting of a single slot, 1 RU router • VIP2 in Cisco 7500 series and Cisco 7000 series routers with the Cisco 7000 series route switch processor (RSP7000) and 7000 series chassis interface (RSP7000CI) PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration...

  • Page 6: Organization

    Provides instructions for configuring the Adapter PA-5EFL port adapter on the supported platforms. Related Documentation Your router and the Cisco IOS software running on it contain extensive features and functionality, which are documented in the following resources: For Cisco IOS software: •...
  • Page 7 • For hardware installation and maintenance information, and the, refer to the following publications: – The installation and configuration guide that shipped with your Cisco 7000 series or Cisco 7500 series router – Second-Generation Versatile Interface Processor (VIP2) Installation and Configuration •...

  • Page 8: Obtaining Documentation

    Cisco provides several ways to obtain documentation, technical assistance, and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation on the World Wide Web at this URL: http://www.cisco.com/univercd/home/home.htm You can access the Cisco website at this URL: http://www.cisco.com...

  • Page 9: Documentation Feedback

    The Cisco TAC is available to all customers who need technical assistance with a Cisco product, technology, or solution. Two levels of support are available: the Cisco TAC website and the Cisco TAC Escalation Center. The avenue of support that you choose depends on the priority of the problem and the conditions stated in service contracts, when applicable.

  • Page 10: Cisco Tac Website

    No workaround is available. Cisco TAC Website You can use the Cisco TAC website to resolve P3 and P4 issues yourself, saving both cost and time. The site provides around-the-clock access to online tools, knowledge bases, and software. To access the Cisco TAC website, go to this URL: http://www.cisco.com/tac...

  • Page 11: Obtaining Additional Publications And Information

    Internetworking Terms and Acronyms Dictionary, Internetworking Technology Handbook, Internetworking Troubleshooting Guide, and the Internetworking Design Guide. For current Cisco Press titles and other information, go to Cisco Press online at this URL: http://www.ciscopress.com Packet magazine is the Cisco monthly periodical that provides industry professionals with the latest •...
  • Page 12 Preface Obtaining Additional Publications and Information PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...

  • Page 13: Overview

    Figure 1-1, provides up to five IEEE 802.3 Ethernet 10Base-FL interfaces for the chassis. The PA-5EFL network interfaces provide a direct connection between the high-speed bus in the router and external networks. Each Ethernet 10Base-FL interface allows a maximum bandwidth of 10 Mbps, for a maximum aggregate bandwidth of 50 Mbps, half-duplex. Each 10Base-FL interface uses two multimode ST-type receptacles for receive (RX) and transmit (TX).

  • Page 14: Chapter 1 Overview

    10Base-FL specification. The Ethernet specifications call the 5EFL device a transceiver, and it is connected to the station with a transceiver cable. The PA-5EFL is not an end station. The IEEE 802.3 specifications refer to the same type of device as a media attachment unit (MAU).

  • Page 15: Leds

    ~ 5 microseconds/km 1. Specified in IEC Publication 793-2[14]. LEDs The PA-5EFL port adapter has one row of five status LEDs (one for each port), and one enabled LED. (See Figure 1-2.) The green-colored LED for each port indicates port status.

  • Page 16: Cables And Connectors

    Cisco 7100 Series Routers Slot Numbering The PA-5EFL port adapter can be installed in port adapter slot 3 in Cisco 7120 series routers, and in port adapter slot 4 in Cisco 7140 series routers.

  • Page 17: Cisco 7200 Series And Cisco Ubr7200 Series Routers Slot Numbering

    Cisco uBR7246 series router. The port adapter slots are numbered slot 1 and slot 2 for the Cisco uBR7246. (Slot 0 is always reserved for the Fast Ethernet port on the I/O controller—if present.)

  • Page 18: Cisco 7301 Router Slot Numbering

    Cable modem card slot 4 Cable modem card slot 5 Cable modem card slot 6 Cisco 7301 Router Slot Numbering The Cisco 7301 router has one standard port adapter slot. See Figure 1-8. Figure 1-8 Port Adapter Slot in the Cisco 7301 Router...

  • Page 19: Vip Slot Numbering

    Note In the Cisco 7000, Cisco 7507, and Cisco 7513 chassis, the VIP motherboard is installed vertically. In the Cisco 7010 and Cisco 7505 chassis, the VIP motherboard is installed horizontally. Interface processor slots are numbered as shown in Figure 1-10.

  • Page 20: Identifying Interface Addresses

    Interface addresses specify the actual physical location of each interface on a router or switch. Interfaces on the PA-5EFL installed in a router maintain the same address regardless of whether other port adapters are installed or removed. However, when you move a port adapter to a different slot, the first number in the interface address changes to reflect the new port adapter slot number.

  • Page 21: Cisco 7100 Series Routers Interface Addresses

    The interface addresses of the interfaces on a PA-5EFL port adapter in port adapter slot 2 are 2/0 through 2/4 (port adapter slot 2 and interfaces 0 through 4). If the PA-5EFL was in port adapter slot 1, these same interfaces would be numbered 1/0 through 1/4 (port adapter slot 1 and interfaces 0 through 4).
  • Page 22 If the VIP2 is inserted in interface processor slot 3, then the interface addresses of the PA-5EFL are 3/1/0 through 3/1/4 (interface processor slot 3, then the interface addresses 0 through 4). If the port adapter was in port adapter slot 0 on the VIP2, these same interface addresses would be numbered 3/0/0 through 3/0/4.

  • Page 23: Chapter 2 Preparing For Installation

    PA-5EFL(=) • VIP2 (for installation in the Cisco 7000 series or Cisco 7500 series chassis only). For information • about the specific VIP models that support the PA-5EFL port adapter, see the “Software and Hardware Requirements”...

  • Page 24: Software And Hardware Requirements

    2. For configuration guidelines on port adapters in the Cisco 7200 series, refer to the Cisco 7200 Series Port Adapter Hardware Configuration Guidelines. 3. The PA-5EFL can be used in the VIP in all Cisco 7500 series routers using the Route Switch Processors (RSPs), and in Cisco 7000 series routers using the RSP7000 and RSP7000CI.

  • Page 25: Checking Hardware And Software Compatibility

    Checking Hardware and Software Compatibility Checking Hardware and Software Compatibility To check the minimum software requirements of Cisco IOS software with the hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether modules within a system are compatible, but it does provide the minimum IOS requirements for individual hardware modules or components.
  • Page 26 Remarque Cette documentation doit être utilisée avec le guide spécifique d'installation du produit qui accompagne ce dernier. Veuillez vous reporter au Guide d'installation, au Guide de configuration, ou à toute autre documentation jointe pour de plus amples renseignements. PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...
  • Page 27 Merk TA VARE PÅ DISSE INSTRUKSJONENE Merk Denne dokumentasjonen skal brukes i forbindelse med den spesifikke installasjonsveiledningen som fulgte med produktet. Vennligst se installasjonsveiledningen, konfigureringsveiledningen eller annen vedlagt tilleggsdokumentasjon for detaljer. PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...
  • Page 28 OBS! SPARA DESSA ANVISNINGAR OBS! Denna dokumentation ska användas i samband med den specifika produktinstallationshandbok som medföljde produkten. Se installationshandboken, konfigurationshandboken eller annan bifogad ytterligare dokumentation för närmare detaljer. PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...

  • Page 29: Electrical Equipment Guidelines

    Never install telephone jacks in wet locations unless the jack is specifically designed for wet • locations. Never touch uninsulated telephone wires or terminals unless the telephone line has been • disconnected at the network interface. Use caution when installing or modifying telephone lines. • PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...

  • Page 30: Preventing Electrostatic Discharge Damage

    You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: Turn the television or radio antenna until the interference stops.
  • Page 31 Note The PA-5EFL has been designed to meet these requirements. Modifications to this product that are Note not authorized by Cisco Systems, Inc., could void the various approvals and negate your authority to operate the product.
  • Page 32 Chapter 2 Preparing for Installation FCC Class A Compliance PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration 2-10 OL-3495-02...

  • Page 33: Chapter 3 Removing And Installing Port Adapters

    C H A P T E R Removing and Installing Port Adapters This chapter describes how to remove the Cisco PA-5EFL port adapter from supported platforms and also how to install a new or replacement port adapter. This chapter contains the following sections: •...

  • Page 34: Online Insertion And Removal

    Several platforms support online insertion and removal (OIR) of port adapters; therefore, you do not have to power down routers when removing and replacing a PA-5EFL port adapter on Cisco 7100 series routers, Cisco 7200 series routers, Cisco uBR7246 series routers, or the Cisco 7301 router.

  • Page 35: Warnings And Cautions

    Some platforms have an ESD connector for attaching the wrist strap. Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing. PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...

  • Page 36: Port Adapter Removal And Installation

    Port Adapter Removal and Installation In this section, the illustrations that follow give step-by-step instructions on how to remove and install port adapters. This section contains the following illustrations: Cisco 7200 Series—Removing and Installing a Port Adapter, page 3-6 • •...

  • Page 37: Cisco 7100 Series-Removing And Installing A Port Adapter

    Step 8 After the port adapter is properly seated, lock the port adapter retaining mechanism. PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...

  • Page 38: Cisco 7200 Series-Removing And Installing A Port Adapter

    Step 7 After the port adapter is properly seated, lock the port adapter lever. (See A.) PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...

  • Page 39: Cisco Ubr7200 Series-Removing A Port Adapter

    With the port adapter halfway (unlocked position) out of the slot, disconnect all cables from the port adapter. After disconnecting the cables, pull the port adapter from its chassis slot. PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...

  • Page 40: Cisco Ubr7200 Series-Installing A Port Adapter

    Step 4 After the port adapter is properly seated, lock the port adapter lever or retention clip, depending on your system. (See illustration on preceding page.) PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...

  • Page 41: Cisco 7301 Router-Removing And Installing A Port Adapter

    After the port adapter is properly seated, turn and secure the port adapter latch in the upright, locked position. (See A.) Tighten the screw to ensure the port adapter remains firmly in place. PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...

  • Page 42: Vip-Removing And Installing A Port Adapter

    Use the ejector levers to seat the VIP in the interface processor slot. Tighten the captive installation screws on the VIP. (See C.) PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration 3-10 OL-3495-02...

  • Page 43: Connecting An St Fiber-Optic Cable

    Connect a PA-5EFLport adapter RX port to the appropriate TX port of the repeater, hub, DTE, or other external 10Base-FL equipment. Step 4 Connect a PA-5EFL port adapter TX port to the appropriate RX port of the repeater, hub, DTE, or other external 10Base-FL equipment. Step 5 Repeat Steps 1 and 4 for each additional PA-5EFL interface connection you require.
  • Page 44 Chapter 3 Removing and Installing Port Adapters Connecting an ST Fiber-Optic Cable PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration 3-12 OL-3495-02...

  • Page 45: Chapter 4 Configuring The Pa-5Efl Port Adapter

    C H A P T E R Configuring the PA-5EFL Port Adapter To continue your Cisco PA-5EFL port adapter installation, you must configure the Ethernet interfaces. The instructions that follow apply to all supported platforms. Minor differences between the platforms—with Cisco IOS software commands—are noted.

  • Page 46: Configuring The Interfaces

    Bridging protocols you plan to use If you installed a new PA-5EFL port adapter or if you want to change the configuration of an existing interface, you must enter configuration mode to configure the new interfaces. If you replaced a PA-5EFL port adapter that was previously configured, the system recognizes the new interfaces and brings each of them up in their existing configuration.
  • Page 47 The example is for the 0 interface on a port adapter (ethernet) and slot/port in slot 1. (port-adapter-slot-number/ interface-port-number) Router(config-if)# interface ethernet 1/0 Router(config-if)# shutdown Ctrl-Z Router# PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...
  • Page 48 The example is for interface 0 on a port slot/port (port-adapter-slot-number/ adapter in port adapter slot 1. interface-port-number) Router# show interfaces ethernet 1/0 Serial 1/0 is administratively down, line protocol is down [Additional display text omitted from this example] PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...
  • Page 49 1 of a VIP2 in (interface-processor-slot-number/ interface processor slot 1. port-adapter-slot-number/ Router# show interfaces ethernet 1/1/0 interface-port-number) Ethernet 1/1/0 is administratively down, line protocol is down [Additional display text omitted from this example] PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...

  • Page 50: Performing A Basic Configuration

    Cisco 7140 series routers interface ethernet, followed by The example is for the first interface of a slot/port port adapter in port adapter slot 4. (port-adapter-slot-number/ Router(config)# interface ethernet 4/0 interface-port-number) Router(config-if)# PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...
  • Page 51 EXEC command interpreter prompt. Step 8 Write the new configuration to NVRAM as follows: Router# copy running-config startup-config [OK] Router# This completes the procedure for creating a basic configuration. PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration OL-3495-02...

  • Page 52: Checking The Configuration

    PA-5EFL appears in them correctly. Sample displays of the output of selected show commands appear in the sections that follow. For complete command descriptions and examples, refer to the publications listed in the “Related Documentation”...

  • Page 53: Using The Show Version Or Show Hardware Commands

    Display the configuration of the system hardware, the number of each interface type installed, the Cisco IOS software version, the names and sources of configuration files, and the boot images, using the ) command. The following sections offer some platform-specific...
  • Page 54 Router uptime is 24 minutes System restarted by power-on System image file is "disk0:c7100-is-mz.120-4.XE" cisco 7120-bad (EGR) processor with 61440K/69632K bytes of memory. R527x CPU at 225Mhz, Implementation 40, Rev 10.0, 2048KB L2 Cache Last reset from power-on Bridging software.
  • Page 55 System returned to ROM by reload at 00:01:51 UTC Sat Jan 1 2000 System image file is "tftp://10.1.8.11/tazii/images/c7301-js-mz" cisco 7301 (NPE-G1) processor (revision A) with 491520K/32768K bytes of memory. Processor board ID 0 BCM1250 CPU at 700Mhz, Implementation 1, Rev 0.2, 512KB L2 Cache 1 slot midplane, Version 2.0...

  • Page 56: Using The Show Diag Command

    0x20:01 D3 FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x30:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF To use the show diag command with the Cisco 7140 series router, replace the slot argument 3 with 4. Note...
  • Page 57 0x20: 01 0D FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF Port adapters used with the Cisco 7200 VXR routers require the correct base hardware revision in order Note to function.

  • Page 58: Using The Show Interfaces Command

    In this example, the five ethernet interfaces (0 to 4) are on a port adapter in port adapter slot 3 of a Cisco 7120 series router; also, most of the status information for each interface is omitted. (Interfaces are administratively shut down until you enable them.)
  • Page 59 Following is an example of the command, which shows all of the show interfaces ethernet information specific to interface 0 on a PA-5EFL port adapter installed in port adapter slot 3 of a Cisco 7120 router. Router# show interfaces ethernet 3/0...
  • Page 60 Chapter 4 Configuring the PA-5EFL Port Adapter Checking the Configuration To use the show interfaces ethernet command with the Cisco 7140 router, replace the interface address Note argument 3/0 with 4/0. Cisco 7200 Series and Cisco uBR7200 Series Routers Following is an example of the...
  • Page 61 0 output buffer failures, 0 output buffers swapped out Cisco 7301 Router Following is an example of the command for Cisco 7301 routers. Most of the status show interfaces information for each interface is omitted. (Interfaces are administratively shut down until you enable them.)
  • Page 62 Chapter 4 Configuring the PA-5EFL Port Adapter Checking the Configuration VIP2 in Cisco 7000 Series or Cisco 7500 Series Routers Following is an example of the command used with the VIP2. In this example, the five show interfaces ethernet interfaces (0 to 4) are on a port adapter port adapter slot 0 of a VIP2 in interface processor slot 3;...

  • Page 63: Using The Ping Command To Verify Network Connectivity

    • When no compact serial cable is attached to the PA-5EFL interface port, or if a DCE cable is attached to a port that is configured as line protocol up, the command tests the path...
  • Page 64 Chapter 4 Configuring the PA-5EFL Port Adapter Checking the Configuration PA-5EFL Ethernet 10Base-FL Port Adapter Installation and Configuration 4-20 OL-3495-02...

Table of Contents