Table of Contents
Advertisement
Feature #18 Door Activated Anti-Carjacking Protection
Factory Default Setting
Off
Option:
On
This form of Anti-Carjacking is initiated by a door being opened. The Anti-
Carjacking protection, including the three ways to initiate it are described on
pages 24 & 25.
Feature #19 Remote Activated Anti-Carjacking Protection
Factory Default Setting
Off
Option:
On
This form of Anti-Carjacking is initiated by a signal from the transmitter (or
optional 2-way controller). The Anti-Carjacking protection, including the
three ways to initiate it are described on pages 24 & 25.
Feature #20 Open Door Warning Upon Arming
Factory Default Setting
Off
Option:
On
When this feature is turned on, if one of the vehicle's doors is open at the
time that the system is armed via the transmitter, the siren will chirp 3 times
and the parking lights will flash 3 times instead of once.
Feature #21 Red "panic" Button Operation
Factory Default Setting
Panic
(press "arm/lock" button to program)
Options:
3rd Channel
(press "disarm/unlock" button to program)
4th Channel
(press "OPTION" button to program)
5th Channel
(press red "panic" button to program)
This feature changes how the transmitter's red "panic" button operates.
Normal operation, or the default setting, has the "panic" button operate the
Panic feature. This feature allows changing it to operate the 3rd channel or
either of the two other optional channel outputs. Panic can still be operated,
by the alternative methods of pressing either the "arm/lock" and "disarm/
unlock" button for 3 seconds.
This feature will also operate with the optional 2-way controller in the
same fashion as described
Feature #22 Remote Start Run Time
Factory Default Setting
10 Minutes
(press "disarm/unlock" button to program)
Options:
5 Minutes
(press "arm/lock" button to program)
(press "disarm/unlock" button to program)
(press "arm/lock" button to program)
(press "disarm/unlock" button to program)
(press "arm/lock" button to program)
(press "disarm/unlock" button to program)
(press "arm/lock" button to program)
Page - 36
lock" button will simply rearm the system, and vice versa when pressing the
"disarm/unlock" button.
Arming Bypass: Upon arming, if any system sensing circuit is inoperable,
that circuit only will automatically be bypassed. When an unsecured
sensing circuit is in a bypassed state, all other normally operating circuits
will be protected. Should the bypassed circuit become secured, it will
automatically be reinstated for protection 5 seconds later. When certain
protection circuits are bypassed, such as the hood/trunk and impact sensor,
and the system is armed, it will indicate this by chirping the siren three time
and flashing the parking lights three times instead of the normal arming
indication of one chirp and one flash.
For example, should the trunk be open, you can still arm the system with
the transmitter, and in this case the arming indicator will be 3 siren chirps
and 3 parking light flashes. Arming Bypass will only operate when arming
the system with the transmitter.
Sensor Bypass: When arming the MAX-EDP system with the
transmitter, you may conveniently and easily temporarily deactivate the
impact sensor without affecting the system's other sensing circuits. To
deactivate the sensor, arm the system by pressing the "arm/lock" button,
then press and release the transmitter's "
seconds. You will hear a second siren chirp confirming that the security
system has armed without the sensor protecting the vehicle. The next time
the system is armed normally with one "arm/lock" button press, the sensor
will again be part of your protection.
Automatic "Last Door Arming" of the System
The MAX-EDP can also be programmed to automatically arm itself, and
in this process, to lock or not lock the doors. When this feature is utilized,
closing the vehicle's last door will cause the siren to chirp once, the parking
and interior lights to flash once and the Status Light to start rapidly flashing
red. Thirty seconds later the siren will chirp again and the lights will flash
again, the doors will lock (which is separately programmable) and the
Status Light will slow to a steady red flash, confirming that the security
system is fully armed. If a point of entry is reopened before the single siren
chirp at 30 seconds, the Last Door Arming process stops, and will reset to
start over when the point of entry is again closed. All protected entries must
be closed to initiate the Last Door Arming sequence.
To temporarily prevent the system from automatically Last Door Arming,
" button within three
OPTION
Page - 9
Advertisement
Table of Contents
