Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Wavecom WMOD2B
Summary of Contents for Wavecom WMOD2B
- Page 1 WMOD2B dual-band 900 / 1800 MHz modem USER MANUAL...
-
Page 2: Table Of Contents
2.3.1 Switching the GSM modem on/off 2.3.2 Voltage range 2.3.3 Overvoltage/undervoltage 2.3.4 Power supply cable 2.3.5 Input/output electrical characteristics defined for all external connections 2.3.6 Protection/on-board network connection 3. DESCRIPTION OF THE INTERFACES 3.1 LED Function 3.2 Connectors 4. TECHNICAL DATA Wavecom WMOD2B Modem... - Page 3 5.2 The modem always returns «Error» when trying to issue a communication 5.3 The modem always returns «No carrier» when trying to issue a communication 6. REFERENCE ACCESSORIES 7. NOTES ON SAFETY 7.1 General safety 7.2 Vehicle safety 7.3 Car And Maintenance 7.4 Your responsibility 8. GENERAL INFORMATIONS Wavecom WMOD2B Modem...
-
Page 4: Product Description
- 1 Power supply cable + fuse - 1 User manual (this document) Product presentation The Wavecom WMOD2B modem supports DATA and FAX transmission, Short Messages (Point to Point and Cell Broadcast) and VOICE calls. The connectors binded to the body guarantee output and input connections. -
Page 5: Physical Characteristics
. e t i r o o i t . t i Temperature range Operating conditions : From -20 C to +55 C Storage conditions From -25 C to +70 C Wavecom WMOD2B Modem... -
Page 6: Installation/Start-Up
In order to extract or to insert the Micro SIM card, it is necessary to press the SIM holder ejector with a sharp element (a pen for example). If this sequence is not respected, the SIM holder could be damaged. Wavecom WMOD2B Modem... -
Page 7: Electrical Characteristics
5 to 32V DC 2.3.3 Overvoltage/undervoltage Correct operation of the Wavecom WMOD2B modem in communication mode is not guaranteed if input voltage fall below 5V. The modem is protected against voltage over 32V. When input voltages exceed 32V, the supply voltage is disconnected in order to protect the electronic components from an overvoltage. -
Page 8: Power Supply Cable
24x0.2 mm Section 0.75 mm Stripped wire, tinned over 5 mm Cables stripped over 200 mm, protected by their own sheath Connector Molex Micro-Fit 3.0 Standard cable sheath Side view Figure 3 Power supply cable Wavecom WMOD2B Modem... -
Page 9: Input/Output Electrical Characteristics Defined For All External Connections
The tests are carried out with a 3V SIM card. The power consumption might vary of 5% over the whole operating temperature range (-20 C to +55 C) 2.3.6 Protection/on-board network connection The modem is protected by a fuse directly binded on the power supply cable. Wavecom WMOD2B Modem... -
Page 10: Description Of The Interfaces
Device switched on - Connecting to network - LED flashing slowly Device switched on - Idle mode (registered on network) - LED flashing rapidly Device switched on - Transmission mode Connectors n i l n i l t i s « » Wavecom WMOD2B Modem... -
Page 11: Antenna Connector
- Press the yellow button to eject the holder. - Insert the SIM card. - Check that it fits into place correctly. SIM card Extractible SIM card holder Figure 5 SIM card holder Yellow button to eject the holder (with a sharp element) Wavecom WMOD2B Modem... - Page 12 Figure 6 15 pins SUB D connector (high density) i r r Pins assignment for 15 pins SUB D Connector ) - ( ) - ( Wavecom WMOD2B Modem...
- Page 13 Figure 7 4 pins Micro-Fit connector 4 pins Micro-Fit 3.0 can be ordered from a supplier called MOLEX. Wavecom WMOD2B Modem...
-
Page 14: Technical Data
' n « » « » l l a s i l l l a s i l t ' n « » « » l l a l l a & Wavecom WMOD2B Modem... -
Page 15: Troubleshooting: Specific Defaults Possibly Encountered
The factory setting for the baud rate is 9600 bps. D) Does any other program interfere with your communication program (conflict on communication port access)? If yes, close any application likely to interfere (e.g. mouse or printer driver). Wavecom WMOD2B Modem... -
Page 16: The Modem Always Returns «Error» When Trying To Issue A Communication
Is the modem registered on the network? Does the AT-Command AT + CREG? answers 0,1 (registered) or 0,5 (registered roaming)? If not, check that the received signal is strong enough to synchronize on the Network (use AT+CSQ). Wavecom WMOD2B Modem... -
Page 17: The Modem Always Returns «No Carrier» When Trying To Issue A Communication
For all other codes, and/or details, see AT commands manual. Wavecom WMOD2B Modem... - Page 18 Then, insure the selected bearer type is supported by the Network. If no success, try bearer selection type: AT+CBST=0,0,3. Insure the SIM Card is available for Data/Fax calls. Further questions For further troubleshooting information, please check our Frequently Asked Questions on www.wavecom.com (customer support section). Wavecom WMOD2B Modem...
-
Page 19: Reference Accessories
6. REFERENCE ACCESSORIES The following accessories have been qualified for the WMOD2B modem: Dual-band antenna : ALLGON 1140.26 Antenna adaptor : SMA/FME adaptor from PROCOM Power adaptor : EGSTON N2 EFSW 12V 1A mounted with micro-fit connector from MOLEX. 7. NOTES ON SAFETY... -
Page 20: Vehicle Safety
Do not abuse your GSM Modem by dropping, knocking, or violent shaking. Rough handling can damage it. Do not place the GSM Modem alongside computer discs, credit or travel cards or other magnetic media. The information contained on discs or cards may be affected by the phone. Wavecom WMOD2B Modem... -
Page 21: Your Responsibility
The use of third party equipment or accessories, not made or authorized by Wavecom may invalidate the warranty of GSM Modem. Do contact an authorized Service Center in the unlikely event of a fault. Your Responsibility This GSM Modem is under your responsibility. Please treat it with care respecting all local regulations. It is not a toy therefore keep it in a safe place at all times and out of the reach of children. -
Page 22: General Informations
Some mentioned products are registred trademarks of them respective companies. Copyright This manual is copyrighted by Wavecom with all rights reserved. No part of this manual may be reproduced in any form without the prior written permission of Wavecom. No patent liability is assumed with respect to the use of the information contained herein. - Page 23 Tel: +852 2824 0254 - Fax: +852 2824 0255 WAVECOM Asia Pacific Limited - Tokyo Branch - 4/F , East Tower, Otemachi First Square, 1-5-1 Otemachi, Chiyoda-ku Tokyo 100-0004 - Japan - Tel: +81 (0)3 5219 1350 - Fax: +81 (0)3 5219 1450...
Need help?
Do you have a question about the WMOD2B and is the answer not in the manual?
Questions and answers