Ge cameras ktc-117v3/117v9, ktc-217cv3/217cv9 ktc-247cev3/247cev9 user manual (20 pages)
Summary of Contents for GE UVD-EVRDNR(-P)
Security UVD-EVRDNR(-P) Camera User Manual REV 01.00 • ISS 02SEP09...
Disclaimer The information in this document is subject to change without notice. GE Security, Inc. (“GE Security”) assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or indirectly, of the use or application of any of the contents of this document.
Preface This is the UVD-XP3DNR(-P) Camera. This document includes an overview of the product and detailed instructions explaining: • how to connect the camera; and • how to program the camera; and • how to adjust the camera angle and focus To use this document effectively, you should have the following minimum qualifications: •...
Product description The UVD-EVRDNR color video camera uses a digital signal processor (DSP) to process video signals. The video camera includes a microcontroller to provide high-quality images with high-color reproduction and sharp pictures. Features Camera features include: • Super HAD (hole accumulated diode) technology with 410,000 pixels NTSC (470,000 PAL).
Components The UVD-EVRDNR cameras consist of the following parts: • The camera assembly (Figure 1 below) • Monitor output cable (Figure 2 below) • Mounting screws, wall anchors, and hex key Use the video output BNC and power jack for normal system operation. Use the monitor output cable for installation and maintenance.
OSD control pad The onscreen display (OSD) control pad (Figure 4) is a five-direction joystick that provides the ability to manually control the camera functions. Table 1 below lists the OSD control pad functions and describes their use. Figure 3: OSD control pad OSD control pad Table 1: OSD control pad functions Pad directions...
Cable connection To make cable connections, do the following: 1. Connect a coaxial cable from the camera’s BNC connector to a CCTV monitor or video recording device. 2. Connect a 12 VDC or 24 VAC power supply to the power input. The label on the camera gives the following information: Red cable.
Focus adjustment To adjust the camera zoom and focus, see Figure 5 below and do the following: 1. Loosen the zoom ring thumbscrew. 2. Turn the zoom ring to set the desired zoom. 3. Tighten the zoom ring thumbscrew. 4. Loosen the focus ring thumbscrew. 5.
Figure 6: Setup menu • To close the Setup menu and return to normal camera operation mode, move the cursor to End at the bottom of the screen and press Enter. Note: If you do not press the OSD control pad for one minute while any setting menu is displayed, all modified data will be stored and the camera will return to normal camera picture mode.
5. Move the cursor to the blank character position between “z” and “,”. 6. To delete a character, select the character so that it blinks and either move the cursor to the blank character position between the “z” and “,” or move it to the DEL position and press Enter.
Figure 10: DC Lens menu Table 2 below describes the menu items in the DC Lens menu. Table 2: DC Lens menu description Menu item Description Iris level Press Left or Right to adjust the level for autoiris lens to control light entering camera (for DC type).
2. To set ME, press Enter when the ME option is displayed. The ME menu appears (Figure 12 below). Figure 12: ME menu 3. Press Up or Down to select an item. 4. Adjust the Shutspeed to 1/50, 1/120, 1/250, 1/500, 1/1,000, 1/2,000, 1/5,000, or 1/10,000 sec.
5. Move the cursor on the Lux/Delay menu to the Delay time position. Press Left or Right to adjust delay time from 5 to 60 seconds. Figure 14: Lux/Delay menu 6. To set Schedule, press Enter when display Schedule menu (Figure 15 below). 7.
White balance White balance (WB) tells the camera what the color white looks like. Based on this information, the camera will then display all colors correctly. There are 3 methods to determine the WB: • ATW (auto tracking white balance). The value used depends on the lighting condition selected.
Figure 17: Picture menu 2. Move the cursor to the Bright position, while observing the color video monitor, waveform monitor, or oscilloscope. Press Left or Right to adjust the brightness level. 3. Move the cursor to the Gamma position. Press Left or Right to adjust gamma correction to one of nine gamma curves.
Figure 18: Misc menu External synchronization To adjust the external synchronization, do the following: 1. Move the cursor to the Ext sync position. 2. Press Left or Right to align the camera synchronization type. 3. When LineLock is selected, press Enter to display the Ext Sync menu. 4.
2. Press Left or Right to select one of eight masks to be displayed onscreen to cover the private areas. 3. Move the cursor to the second line. Press Left or Right to show or hide the mask. 4. Move the cursor to Color type. Press Left or Right to select one of three types of masking color (White, Gray, or Black).