Related Manuals for HAMPTON BAY Dawson 581 645
Summary of Contents for HAMPTON BAY Dawson 581 645
-
Page 1: Ceiling Fan
581 645 Dawson Ceiling Fan Owner’s Manual Dawson Ventilador de Techo de 1,37 Manual del Propietario... -
Page 2: Table Of Contents
54” Dawson Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. Ceiling Fan by Hampton Bay Date Purchased Table of Contents Store Purchased Safety Rules ....1 581-645 UL Model No. -
Page 3: Safety Rules
Safety Rules - Read and Save These Instructions To reduce the risk of electric shock, insure electricity has been turned off After making electrical connections, spliced conductors should be turned at the circuit breaker or fuse box before beginning. upward and pushed carefully up into outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding All wiring must be in accordance with the National Electrical Code conductor on one side of the outlet box and ungrounded conductor on the... -
Page 4: Unpacking Your Fan
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items: Set of blades (5) Set of blade arms (5) Blade Attachment Hardware (16 Screws with Fiber Washers) Canopy assembly Light plate Ball/downrod assembly (1) Light kit Electrical Hardware &... -
Page 5: Installing Your Fan
Installing Your Fan Provide Strong Support Tools Required Figures 1~3 are examples of different ways to mount the outlet box. Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Recessed Ceiling Outlet Box Mounting Plate Mounting Options Figure 3 Outlet Box Note: You may need a longer downrod to If there isn't an existing UL listed mounting box,... - Page 6 Hanging the Fan WARNING Motor Wires FAILURE TO PROPERLY INSTALL COTTER PIN REMEMBER to turn off the power. Follow the AS NOTED IN STEP 5 COULD RESULT IN FAN Pin in Locked LOOSENING AND POSSIBLY FALLING. Ceiling Canopy Positioon steps below to hang your fan properly. Remove the decorative canopy bottom cover Tighten two set screws at top of the fan motor Ball/Downrod...
-
Page 7: Changing The Downrod
Changing the Downrod Installing Fan to UL Listed Outlet Box the Electrical Box (Optional) NOTE: Your fan comes with a 4" downrod WARNING 120V attached to the hanger ball. In addition you have Wires TO REDUCE THE RISK OF FIRE, ELECTRIC been provided with a 6"... -
Page 8: Making The Electrical Connections
Making the Electrical receiver. Secure the wire connections with the plastic wire connecting nuts provided. Connections Frequency Switch (Figure 11) Receiver to house supply wires electrical connections: Connect the black (hot) WARNING wire from the ceiling to the black wire marked TO AVOID POSSIBLE ELECTRICAL SHOCK, BE "AC in L"... - Page 9 WARNING SUPPLY CIRCUIT CHECK TO SEE THAT ALL CONNECTIONS ARE Outlet Box TIGHT, INCLUDING GROUND, AND THAT NO BARE WIRE IS VISIBLE AT THE WIRE NUTS. Ground EXCEPT FOR THE GROUND WIRE. Ceiling Conductor BLACK Mounting Bracket WARNING Outlet Box Screws ELECTRICAL DIAGRAMS...
-
Page 10: Attaching The Fan Blades
Attaching the Fan Blades CAUTION Motor MOTOR IS SHIPPED WITH RUBBER PACKING MOUNTS TO PREVENT MOVEMENT DURING TRANSPORTATION. REMOVE RUBBER PACKING MOUNTS FROM FAN MOTOR ASSEM- Rubber Packing Mounts Blade Arm BLY AND DISCARD PRIOR TO ATTACHING Slot BLADE ARMS. (FIG. 13) Screws Attach blades to blade arm using the screws Figure 13... -
Page 11: Installing The Light Plate
Blade Balancing Installing the Light Plate The following procedure should correct most fan Remove 1 of the 3 screws from the mounting Touching Ceiling wobble. Check after each step. ring and loosen the other 2 screws. (Do not remove) Check that all blade and blade bracket screws are secure. -
Page 12: Installing The Light Kit
Installing the Fan without Light Kit NOTE LIGHT BULBS HAVE NO WARRANTY; CAN BE (Optional) Light Kit PURCHASED AT ANY HOME DEPOT STORE. Install the mounting plate to the mounting ring NOTE with 3 screws provided. (Fig. 19) BEFORE STARTING INSTALLATION, DISCON- NECT THE POWER BY TURNING OFF THE Place mounting plate cover over mounting CIRCUIT BREAKER OR REMOVING THE FUSE... -
Page 13: Operating Your Transmitter
Operating Your Transmitter Installing the Battery: Restore power to the ceiling fan and test for proper operation. Install 12V MN21/A23 battery (not included), to "HI, MED, LOW" buttons: prevent damage to transmitter, remove the battery These three buttons are used to set the fan if not used for long periods. - Page 14 Speed settings for warm or cool weather depend on factors such as the room size, ceiling height, number of fans, etc. The Reverse switch is located on the top of motor housing. Slide the switch to the Left for warm weather operation.
-
Page 15: Care Of Your Fan
Care of Your Fan Troubleshooting PROBLEM SOLUTION Here are some suggestions to help you maintain your fan. Fan will not start Check main and branch circuit fuses or breakers. Because of the fan's natural movement, some Check line wire connections to the fan and switch wire connections in connections may become loose. -
Page 16: Specifications
Specifications FAN SIZE SPEED VOLTS AMPS WATTS N.W. G.W. C.F. 0.36 3100 15.73 kgs 17.90 kgs 0.52 4800 54” MED. 3.25’ (34.61 lbs) (39.38 lbs) 0.58 6100 HIGH These are approximate measures. They do not include Amps and Wattage used by the light kit. -
Page 17: Warranty Information
Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time You must present a copy of the original purchase receipt to obtain warranty of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.