Zm Series Layout - Rear Panel - Samson ZM125 Owner's Manual

ZM Series Layout - Rear Panel

1 2
OUTPUT
Constant Voltage 100V/70V/25V
COM
SAMSON
FUSE T2AL/250V
ZM125
125 WATT ZONE AMPLIFIER
230 V
115 V
115Vac/230Vac
50Hz/60Hz, 167W
19 18
1- 25V, 70V and 100V (output connector) - Ten-
contact Euroblock connector for connecting the 25V,
70V and 100V constant voltage outputs.
2 - LO-Z (output connector) - Two-contact Euroblock
connector for connecting the 4-Ohm speaker output.
3 - AMP IN and PRE-AMP OUT (connectors) – These
1/4-inch phone jacks are used to connect an external
effect processor.
4 - MOH VOLUME (control knob) –This control knob
allows you to adjust the level of the Music on Hold
sound source.
5 - MOH (selection switch) – The slide switch is used
to chose the Music on Hold sound source from the
output of the internal mixer or an external sound
source (like a CD or MP3 player).
6 - CHIME VOLUME - (control knob) – The control knob
is used to adjust the level of the Chime tone.
7 - GAIN (control knobs) – The trim knobs are used to
set the input sensitivity for each input channel.
8 - PRIORITY MIC (switch) – When set to on, this slide
switch configures mic channels 1 and/or 2 to mute
the other input channels when a signal is present on
the connected microphones.
9 - PHANTOM POWER (switch) – Used this slide switch
to activate the phantom power on mic channels 1
and/or 2.
10 - MIC/LINE INPUTS (connectors) – Channels 1 and
2 employ combination connectors with XLR and
1/4-inch inputs, which can accept either mic or line
signals.
3 4
75 FM 300
Lo-Z
AMP IN
PRE-AMP
OUT
LINK IN
WARNING CAUTION
DO NOT EXPOSE FOR CONTINUED
THIS EQUIPMENT PROTECTION AGAINST
TO RAIN OR RISK OF FIRE, REPLACE
MOISTURE ONLY SAME TYPE FUSE
LINK OUT
AVIS ATTENTION
RISQUE DE CHOC UTILISER UN FUSIBLE
ELECTRONIQUE NE DE RECHANGE MEME
PAS OUVRIR TYPE
17 16 15
5
6
MUSIC ON HOLD CHIME
MIN MAX MIN MAX -6/+14 -50/-30 -6/+14 -50/-30
GAIN GAIN
VOLUME VOLUME
INT. EXT.
REMOTE MIC LINE/
H C G
LINE
EXT. MOH
MIN MAX
MIC MIC
GAIN
TELE-PAGING
H C G H C G SW
14 13
12
11 - MIC INPUTS (connectors) – Channels 3 and 4
are microphone level inputs on standard XLR
connectors.
12 - MIC/LINE INPUTS (connectors) – Input channels 5
and 6 feature 1/4-inch and RCA connectors for mic
or line level input signals.
13 - REMOTE MIC input connector – Connect the
paging microphone to this four-contact Euroblock
connector.
14 - REMOTE MIC GAIN (control knob) – This trim
control is used to set the input sensitivity for the
remote microphone input.
15 - TELE PAGING (connector) – This three-contact
Euroblock connector is used to connect the ZM
series to a business telecom system so that pages
can be made from any handset.
16 - MOH OUTPUT (connector) - This three-contact
Euroblock connector is used to attach an external
sound source for the Music on Hold system.
17 - LINK IN and LINK OUT (connectors) - Use these
connectors to expand your system by adding a
second ZM series mixer/amplifier.
18 - VOLTAGE SELECTION (switch) - Used to select the
operation voltage for either 115 or 230 Volts. Be
sure to check the correct operating voltage for your
particular country.
19 - AC INLET – Connect the supplied IEC power cable
here.
4
7
-6 -50 -6 -50 -6 -50 -6
GAIN GAIN GAIN GAIN
ON OFF ON
PRIORITY PRIORITY
ON OFF ON
PHANTOM PHANTOM
MIC MIC MIC
10
11
8
-50
OFF
OFF
MIC
9