Stanley ID07 User Manual
Hydraulic hand held impact drill
Hide thumbs
Also See for ID07:
- User manual (24 pages) ,
- Service manual (24 pages) ,
- Safety, operation & maintenance (16 pages)
Subscribe to Our Youtube Channel
Related Manuals for Stanley ID07
Summary of Contents for Stanley ID07
- Page 1 ID07 HYDRAULIC IMPACT DRILL afety peratiOn and aintenance USer ManUaL © 2010 Stanley Black & Decker, Inc. New Britain, CT 06053 U.S.A. 49228 12/2010 Ver. 8...
-
Page 2: Declaration Of Conformity
Provisiones especiales: Disposizioni speciali: Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA... -
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative. -
Page 4: Safety Symbols
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► ID07 User Manual... -
Page 5: Safety Precautions
Keep all parts of your body away from the rotating the space provided in this manual. parts. Long hair or loose clothing can become drawn The model ID07 Hydraulic Impact Drill will provide safe into rotating components. and dependable service if operated in accordance with •... -
Page 6: Tool Stickers & Tags
OPERATION MANUAL. OPERATION MANUAL. TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR. TOOL OPERATOR. SEE OTHER SIDE SEE OTHER SIDE SAFETY TAG P/N 15875 (Shown smaller then actual size) 6 ► ID07 User Manual... -
Page 7: Hose Types
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS. -
Page 8: Hose Recommendations
HOSE RECOMMENDATIONS 8 ► ID07 User Manual... -
Page 9: Htma Requirements
When choosing hydraulic fluid, the expected oil temperature extremes that will be experienced in service determine the most suitable temperature viscosity characteristics. Hydraulic fluids with a viscosity index over 140 will meet the requirements over a wide range of operating temperatures. *SSU = Saybolt Seconds Universal ID07 User Manual ◄ 9... -
Page 10: Operation
OPEN-CENTER (OC) OR CLOSED-CENTER (CC) OPERATION FACTORS THAT AFFECT TORQUE The ID07 can be configured to run on OC or CC circuits. An impact wrench is a rotary hammer that impacts the 1. Determine the system type. head of a bolt or nut. It does not apply a slow steady torque as a standard torque wrench. -
Page 11: Cold Weather Operation
WRENCH OPERATION Damage to the hydraulic system or wrench can result The ID07 is designed for 1/2-inch square or 7/16-inch from use with fluid that is too viscous or too thick. hex drive. During normal operation it is common to see some grease leakage from around the anvil during hard use. -
Page 12: Tool Protection & Care
This can cause damage to internal seals. • Always replace hoses, couplings and other parts with replacement parts recommended by Stanley Hydraulic Tools. Supply hoses must have a mini- mum working pressure rating of 2500 psi/172 bar. •... -
Page 13: Troubleshooting
Too much fluid going through tool. Adjust flow for 4–12 gpm/15–45 lpm maximum. Circuit has contaminants that Replace worn pump and valves. have caused wear and high heat Install a large clean filter and keep generation. circuit fluid clean. ID07 User Manual ◄ 13... -
Page 14: Specifications
Output Torque ..........................500 ft lbs / 675 Nm Connect Size and Type ....................... 3/8 inch NPT Pipe Fitting SOUND AND VIBRATION DECLARATION Test conducted on ID07 operated at standard 5 gpm input Measured A-weighted sound power level, Lwa (ref. 1pW) in decibels 104.6 dBA... -
Page 15: Accessories
15/16 inch Double Square 8 Point Deep Length ....................05115 1 inch Double Square 8 Point Deep Length ...................... 05116 Lineman’s Socket, 13/16 inch and 15/16 inch ....................33155 Lineman’s Socket, 1 inch and 1-1/8 inch ......................33156 ID07 User Manual ◄ 15... -
Page 16: Id07 Parts Illustration
ID07 PARTS ILLUSTRATION 16 ► ID07 User Manual... -
Page 17: Id07 Parts List
08416 (ID07820, ID0782001, ID07920 ONLY) 47436 FEMALE COUPLER (AEROQUIP) 48986 VALVE SPOOL ASSY 03973 MALE COUPLER (PARKER) 47437 MALE COUPLER (AEROQUIP) — — NO ITEM RAILROAD HELP DESK STICKER 49139 SEAL WIPER 25610 (ID07810S ONLY) ID07 User Manual ◄ 17... - Page 18 MAIN HOUSING ASSY 59049 (INCL ITEMS 15, 30) 60677 TRIGGER 60678 TRIGGER MOUNT CASTING 65480 SPRING 60681 TRIGGER LOCK 28808 SPRING 29051 ROLL PIN STICKER, CLOSED-CENTER (SHIPPED 03693 LOOSE WITH ID07810, ID07820 ONLY) 60791 SEAL KIT 18 ► ID07 User Manual...
- Page 20 Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 503-659-5660 / Fax 503-652-1780 www.stanleyhydraulic.com IMPORTANT To fill out a Product Warranty Recording form, and for information on your warranty, visit Stanleyhydraulic.com and select the Warranty tab. (NOTE: The warranty recording form must be submitted to validate the warranty).
Need help?
Do you have a question about the ID07 and is the answer not in the manual?
Questions and answers