Table of Contents
Advertisement
SETUP & OPERATION MANUAL
FEATURES
Simple design for easy set-up and mainte-
nance.
Efficient collection and separation of large
chips which drop into the collector drum
before reaching the impeller.
High quality motor designed specifically
for heavy duty use and long service life.
Remote control for convenient operation
from virtually anywhere in the shop.
1-15 hours Pre-programmed timer run set-
tings in 1 hour increments.
Equipped with an ultra efficient 1 micron
canister filter with total surface area of 48.4
square feet.
Canister filter equipped with crank han-
dle/internal shaker for easy filter cleaning
without removing bag.
Sturdy steel support frame and collection
drum both equipped with casters for com-
plete mobility within the shop.
30 gallon chip collection drum included.
SPECIFICATIONS
AIRFLOW CAPACITY
611 CFM
BLOWER WHEEL DIAMETER
13" (330 MM)
SOUND RATING
80 DB
INLET DIAMETER
(1) 5" (127 MM)
OR (2) 4" (102 MM)
STATIC PRESSURE
10" OF WATER
CANISTER FILTER (DIA X H)
15 3⁄4" X 19 3⁄4" (400 X 502 MM)
OVERALL DIMENSIONS (L X W X H)
52 3⁄4" X 32" X 70"
(1340 X 810 X 1780 MM)
MOTOR
1 1⁄2 HP , 110 V, 12 A
WEIGHT
198 LBS (90 kg)
PORTABLE 2 STAGE DUST COLLECTOR
– 1 1/2 HP
MODEL
10-800CF M1
REVISION 1 - JUNE 04/10
© Copyright General® International 06/2010
Advertisement
Table of Contents
Related Manuals for General International 10-800CF M1
Summary of Contents for General International 10-800CF M1
-
Page 1: Specifications
MODEL STATIC PRESSURE 10” OF WATER CANISTER FILTER (DIA X H) 10-800CF M1 15 3⁄4” X 19 3⁄4” (400 X 502 MM) OVERALL DIMENSIONS (L X W X H) 52 3⁄4” X 32” X 70” (1340 X 810 X 1780 MM) MOTOR 1 1⁄2 HP , 110 V, 12 A... - Page 2 THANK YOU for choosing this General ® International model 10-800CF M1 1 1/2 HP Portable 2 Stage Dust Collector. This dust collector has been carefully tested and inspected before shipment and if properly used and maintained, will provide you with years of reliable service.
- Page 3 ® ® GENERAL & GENERAL INTERNATIONAL WARRANTY All component parts of General®, General® International and Excalibur by General International ® products are carefully inspected during all stages of production and each unit is thoroughly inspected upon completion of assembly. Limited Lifetime Warranty Because of our commitment to quality and customer satisfaction, General®...
-
Page 4: Table Of Contents
TABLE OF CONTENTS Rules for safe operation ....Operating Instructions ... . . 17-18 Connecting to a power source ....17 Operating the control panel . -
Page 5: Rules For Safe Operation
RULES FOR SAFE OPERATION To help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as poten- tial hazards. General® International disclaims any real or implied warranty and holds itself harmless for any injury that may result from improper use of its equipment. -
Page 6: Additional Safety Instructions Specific To This Dust Collector
Additional Safety Instructions Specific to this Dust Collector Because each shop situation is unique, no list of safety guidelines can ever be complete. The most important safety feature in any shop is the knowledge and good judgement of the user. Use common sense and always keep safety considerations, as they apply to your individual shop situation first and foremost in mind. -
Page 7: Electrical Requirements
ELECTRICAL REQUIREMENTS BEFORE CONNECTING THE MACHINE TO THE POWER SOURCE, VERIFY THAT THE VOLTAGE OF YOUR POWER SUPPLY CORRESPONDS WITH THE VOLTAGE SPECIFIED ON THE MOTOR I.D. NAMEPLATE. A POWER SOURCE WITH GREATER VOLTAGE THAN NEEDED CAN RESULT IN SERIOUS INJURY TO THE USER AS WELL AS DAMAGE TO THE MACHINE. IF IN DOUBT, CONTACT A QUALIFIED ELECTRICIAN BEFORE CONNECTING TO THE POWER SOURCE. -
Page 8: Identification Of Main Parts And
PORTABLE 2 STAGE DUST COLLECTOR – 1 1/2 HP 10-800CF M1 IDENTIFICATION OF MAIN PARTS AND COMPONENTS A- CONTROL PANEL K- COLLECTION DRUM CASTERS B- FAN HOUSING L- LOWER CROSS BRACES C- HOSE INLET M- CANISTER FILTER HANGERS D- CYCLONE SEPARATOR... -
Page 9: Assembly
UNPACKING AND PREPARATION FOR SET-UP & ASSEMBLY ADDITIONAL REQUIREMENTS FOR SET UP Use caution and wear gloves when handling metal parts such as the belt clamps, which can cut if han- • 1 extra person for help with lifting dled carelessly. •... -
Page 10: Shop Placement / Space Considerations
52 3⁄4” Consider the space requirements for the unit and its use This model 10-800CF M1 is equipped with a 5” main hose when deciding where to install your dust collector in your inlet that is fitted with a dual-inlet “Y” fitting allowing you to shop. -
Page 11: Assembly Instructions
ASSEMBLY INSTRUCTIONS • SERIOUS PERSONAL INJURY COULD OCCUR IF YOU CONNECT THE MACHINE TO THE POWER SOURCE BEFORE YOU HAVE COMPLETED THE SETUP PROCESS. DO NOT HOOK-UP THE MACHINE TO A POWER SOURCE UNTIL INSTRUCTED TO DO SO. • BE SURE TO READ AND UNDERSTAND THIS ENTIRE MANUAL. •... - Page 12 5. Attach the cyclone separator to the fan housing 6. Attach the 4 upper legs A to the fan housing as using 10 bolts and 10 flat washers as shown in A, shown in B, using 16 bolts and 16 flat washers (4 with the connection outlet B facing the side oppo- per legs, C).
- Page 13 12. Stick some foam gasket A around the opening of 13. Attach the 6” outlet to the right side of the fan hous the 6” Outlet as shown in B. Trim off excess gasket ing with 4 bolts and 4 flat washers. with a knife or scissors, C.
- Page 14 18. Attach the canister filter to the hangers, A, using 19. Install one end of the 6” flexible hose A on the 4 x 14 mm bolts and flat washers B. Tighten the filter outlet and the other end on the fan housing 6” bolts securely.
- Page 15 22. Attach the casters A to the bottom of the chip col- 23. Tighten the nuts securely, holding the head of the lection drum B, using 4 x 14 mm hex nuts, 4 x 14 bolts D with the supplied thin 14 mm open end mm lock washers and 8 x 14 mm flat washers C.
- Page 16 26. Install the rubber seal A over the top lip of the drum 27. Secure the drum lid by clamping the 3 lid latches, rim as shown in B. Trim off excess seal wih a knife up as shown (see A and B). or scissors Note: If needed, loosen the handle along the threaded shaft so that the handle can reach the hook of the...
-
Page 17: Operating Instructions
OPERATING INSTRUCTIONS This Model 10-800CF M1 Portable 2 Stage Dust Collector has been designed to capture remove and collect non-metallic dust and wood dust around the workshop and from woodworking machinery and features 15 pre- programmed timer settings in 1 hour increments. -
Page 18: Circuit Breaker
CIRCUIT BREAKER The unit is equipped with a circuit breaker to protect the motor from power surges or spikes in line voltage. In the event of a power surge, the circuit breaker will be automatically tripped thereby cutting off the power to the motor. -
Page 19: Maintenance & Servicing
MAINTENANCE & SERVICING MAKE SURE THE SWITCH IS IN THE "OFF" POSITION AND UNPLUG THE UNIT FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE. This machine operates on 110 V single phase power; if you suspect any electrical problems call a qualified elec- trician to do the verification of the electrical circuit or the machine. -
Page 20: Emptying The Collector Bag & Drum
EMPTYING THE COLLECTOR BAG & DRUM TURN THE SWITCH TO THE "OFF" POSITION AND UNPLUG THE UNIT FROM THE POWER SOURCE BEFORE EMPTYING OR REPLACING THE COLLECTOR BAG OR BEFORE PERFORMING ANY MAINTENANCE. Note: Depending on your needs, shop situation and local reg- ulations collections bags can be emptied and re-used or dis- posed (with their contents) and replaced with a new bag. -
Page 21: Parts List & Diagrams
DIAGRAM... - Page 22 PARTS LIST 10-800CF M1 PART N0. DESCRIPTION SPECIFICATION 10801-01 MOTOR 1.5 HP 10801-01A MOTOR GASKET 10801-01B FLAT WASHER 5/16” x OD18 x 2T 10801-01C HEX HEAD BOLT 5/16” x 3/4” 10801-02 MOTOR BASE PLATE 10801-02A FLAT WASHER 1/4” x OD19 x 2t...
- Page 23 PARTS LIST 10-800CF M1 PART N0. DESCRIPTION SPECIFICATION 10801-14A 3” CASTER 10801-14B FLAT WASHER 3/8" x OD23 x 2t 10801-14C LOCK NUT 3/8" 10801-15 LOWER CROSS BRACE 10801-16 CANISTER HANGER-1 10801-16A HEX HEAD BOLT 1/4" x 1/2" 10801-16B FLAT WASHER 1/4"...
-
Page 24: Wiring Diagram
WIRING DIAGRAM... - Page 25 Notes...
- Page 26 MODEL 10-800CF M1 8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Tel.: (514) 326-1161 Fax: (514) 326-5565 - Fax: (514) 326-5555 - Parts & Service / Order Desk orderdesk@general.ca www.general.ca IMPORTANT When ordering replacement parts, always give the model number, serial number of the machine and...
Need help?
Do you have a question about the 10-800CF M1 and is the answer not in the manual?
Questions and answers