Advertisement
Dust hood rotates 360°.
Support arm extends up to 12".
Wide dust hood captures chips, dust and
debris.
Powerful 1 HP motor features sealed bear-
ings and shaft for quiet, long-lasting oper-
ation.
Comfort grip carrying handle for easy
portability to place the unit where you
need it.
Flexible 4" x 6' (1.8 m) collection hose
included.
Adjustable multi-position steel support
arm to accommodate a variety of
different machines or applications.
INLET DIAMETER
4" (102 mm)
AIRFLOW CAPACITY
700 CFM
HOSE LENGTH
4" (102 mm) X 6' (1.8 m)
DUST HOOD
10" (254 mm) x 4" (102 mm)
SOUND RATING
78 dB
STATIC PRESSURE
4.3 INCHES OF WATER
BAG CAPACITY
15 GAL (655 L)
OVERALL DIMENSIONS (L x W x H)
44
1 ⁄
" x 18
7 ⁄
" x 43
1 ⁄
"
2
8
4
(1130 x 480 x 1100 mm)
MOTOR
1 HP , 110 V, 7 A
WEIGHT
51.7 LBS (23.5 Kg)
FILTRATION CAPACITY
30 MICRONS
REVISION 3 JUN 22/06
https://manual-hub.com/
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for General International 10-050
Summary of Contents for General International 10-050
- Page 1 Dust hood rotates 360°. Support arm extends up to 12”. Wide dust hood captures chips, dust and debris. Powerful 1 HP motor features sealed bear- ings and shaft for quiet, long-lasting oper- ation. Comfort grip carrying handle for easy portability to place the unit where you need it.
- Page 2 Telephone (514) 326-1161 • Fax (514) 326-5555 • www.general.ca THANK YOU for choosing this General International model 10-050 Dust collector. This dust collector has been carefully tested and inspected before shipment and if properly used and maintained, will provide you with years of reliable service. To ensure optimum per- formance and trouble-free operation, and to get the most from your investment, please take the time to read this manual before assembling, installing and operating the unit.
-
Page 3: Handling The Machine
9. Do not vacuum or use this Dust Collector near flam- 20. The use of parts and accessories NOT recommended mable or combustible liquids, gases, gasoline or other by General International may result in equipment mal- fuels, lighter fluid, cleaners, oil or solvent-based paints, function or risk injury. -
Page 4: Unpacking And Checking Contents
PORTABLE DUST COLLECTOR 10-050 U N P A C K I N G A N D C H E C K I N G C O N T E N T S UNPACK AND REMOVE ALL COMPONENTS OF YOUR MACHINE FROM THE BOX AND COMPARE WITH THE PARTS LISTED BELOW. - Page 5 A S S E M B LY STEP 1 - INSTALLING THE CASTERS ON THE BASE FRAME. STEP 2 – MOUNTING THE LOWER SUPPORT ARM. Lay the dust collector on its side as shown and using Using the 2 supplied flange bolts, , loosely attach the supplied wrench, , install the 4 casters,...
- Page 6 STEP 4 - MOUNTING THE DUST HOOD Using the short carriage bolt, , and one lock knob, , attach the “L” bracket, ,and sprocket washer, , to the end of the upper support arm, . The lock knob is used to secure the dust hood (once installed on the “L” bracket) at the desired angle.
-
Page 7: Adjustments And Controls
CONNECTING TO A POWER SOURCE Plug the dust collector into a proper receptacle. Your power tools should be con- nected to a dedicated electrical circuit of not less than #14 wire and should be protected with a 15 amp time lag fuse. If an extension cord is needed, use only 3-wire cords with 3-prong grounded-type plugs and 3-pole receptacles. - Page 8 https://manual-hub.com/...
-
Page 9: Parts List
PARTS LIST 10-050 PART N0. DESCRIPTION SPECIFICATION 10050-01 TUBE CAP 1" 10050-02 SPONGE TUBE COVER 1" x 5" 10050-03 BASE HANDLE 10050-04 FLAT HEAD PHILLIPS SCREW 1/4" x 1" 10050-05 MOTOR 10050-06 SET SCREW 3/8" 10050-07 COLLECTOR BODY 10050-08 BAG CLAMP 5"... - Page 10 10-050 8360, Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Tel.: (514) 326-1161 Fax : (514) 326-5565 Parts & Service Fax : (514) 326-5555 Order Desk orderdesk@general.ca www.general.ca IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.
Need help?
Do you have a question about the 10-050 and is the answer not in the manual?
Questions and answers