Grizzly H7761 Owner's Manual

Grizzly H7761 Owner's Manual

2" x 27" belt & 6" disc combo sander
Hide thumbs Also See for H7761:

Advertisement

Quick Links

MODEL H7761
2" x 27" BELT & 6" DISC
COMBO SANDER
OWNER'S MANUAL
COPYRIGHT © NOVEMBER, 2005 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JK7658 PRINTED IN CHINA

Advertisement

Table of Contents
loading

Summary of Contents for Grizzly H7761

  • Page 1 2" x 27" BELT & 6" DISC COMBO SANDER OWNER'S MANUAL COPYRIGHT © NOVEMBER, 2005 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #JK7658 PRINTED IN CHINA...
  • Page 2 MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.
  • Page 3: Table Of Contents

    Schedule ... 21 Lubricating Sleeve Bearings ... 22 SECTION 7: SERVICE ... 23 Troubleshooting ... 23 Parts Breakdown ... 24 Parts List ... 25 WARRANTY AND RETURNS ... 26 H7761 2" x 27" Belt & 6" Disc Combo Sander Table of Contents...
  • Page 4: Introduction

    INTRODUCTION Foreword We are proud to offer the Model H7761 2" x 27" Belt & 6" Disc Combo Sander. This machine is part of a growing Grizzly family of fine wood- working machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer...
  • Page 5: Machine Data Sheet

    ... Flexible Work Light ...Convenient Tool Tray ... Included 80 Grit Sanding Belt ...Included 80 Grit Sanding disc Specifications, while deemed accurate, are not guaranteed. H7761 2" x 27" Belt & 6" Disc Combo Sander MACHINE DATA SHEET ⁄ " L x 15 ⁄...
  • Page 6: Identification

    Disc Sanding Table Sanding Disc Motor Tracking Knob Belt Tensioning Knob Side Guard Knob Back Stop Angle Knob Table Angle Knobs (rear knob not shown) Adjustable Work Light ON/OFF Switch Tool Storage H7761 2" x 27" Belt & 6" Disc Combo Sander...
  • Page 7: Section 1: Safety

    RESPIRATOR WHEN MACHINERY THAT PRODUCES DUST. Wood dust is a carcinogen and can cause cancer and severe respiratory illnesses. H7761 2" x 27" Belt & 6" Disc Combo Sander ALWAYS USE HEARING PROTECTION MACHINERY. WHEN Machinery noise can cause permanent hearing damage.
  • Page 8 Make sure you know what type of dust you will be exposed to and always wear an approved respirator. H7761 2" x 27" Belt & 6" Disc Combo Sander ADJUSTING KEYS LOCK...
  • Page 9: Additional Safety Instructions For Sanders

    If normal safety precautions are overlooked or ignored, seri- ous personal injury may occur. H7761 2" x 27" Belt & 6" Disc Combo Sander FEEDING WORKPIECE. Firmly grasp the workpiece in both hands and ease it into the machine using light pressure.
  • Page 10: Section 2: Circuit Requirements

    50 feet in length! • The extension cord must also contain a ground wire and plug pin. • A qualified electrician MUST size cords over 50 feet long to prevent motor damage. H7761 2" x 27" Belt & 6" Disc Combo Sander...
  • Page 11: Section 3: Set Up

    When you are completely satisfied with the con- dition of your shipment, you should inventory the contents. H7761 2" x 27" Belt & 6" Disc Combo Sander Inventory After all the parts have been removed from the box, you should have the following items: Inventory (Figure 2) A.
  • Page 12: Items Needed For Set Up

    Note: Because sizes vary for each individual situation, the hardware in this step is not included with the Model H7761. H7761 Base Workbench Figure 3. Mounting machine to the workbench. H7761 2" x 27" Belt & 6" Disc Combo Sander Bolt Flat Washer Flat Washer Lock...
  • Page 13: Hardware Recognition Chart

    Hardware Recognition Chart -11- H7761 2" x 27" Belt & 6" Disc Combo Sander...
  • Page 14: Clean Up

    Ensure child and visitor safety by keep- ing all entrances to the shop locked at all times. DO NOT allow unsuper- vised children or visitors in the shop at any time. H7761 2" x 27" Belt & 6" Disc Combo Sander...
  • Page 15: Attaching Sanding Disc

    Rotate the disc by hand and make sure the sandpaper is firmly attached to the disc. Reattach the disc table as outlined on this page. H7761 2" x 27" Belt & 6" Disc Combo Sander Installing Disc Table Components and Hardware Needed: Sanding Disc Table ... 1 Table Knobs ...
  • Page 16: Aligning Table

    Loosen the screw that secures the angle pointer and adjust the pointer to the 0˚ mark on the scale. Re-tighten the screw that secures the angle pointer. H7761 2" x 27" Belt & 6" Disc Combo Sander...
  • Page 17: Installing Sanding Belt

    Note: Make sure that the arrow on the inside of the sanding belt points the same direction as the belt rotation arrow on the machine. H7761 2" x 27" Belt & 6" Disc Combo Sander Adjusting Sanding Before starting the sander, perform the...
  • Page 18: Installing Back Stop

    Place a hose clamp over the dust hose. Slide the hose over the dust port. Secure the hose airtight with the hose clamp. Check the hose with a light tug to ensure it is secure. H7761 2" x 27" Belt & 6" Disc Combo Sander...
  • Page 19: Section 4: Operations

    Be sure the safety glasses you wear meet the standards of the American National Standards Institute (ANSI). H7761 2" x 27" Belt & 6" Disc Combo Sander Disc Sanding Always keep the workpiece on the side of the wheel that is rotating down toward the table.
  • Page 20: Miter Sanding

    (Figure 13). Figure 13. Mitering with the table angled. Move the workpiece slowly back and forth across the downspin side of the disc. H7761 2" x 27" Belt & 6" Disc Combo Sander...
  • Page 21: Belt Sanding

    Use the back stop to prevent the workpiece from being thrown off by the rotation of the sanding belt. H7761 2" x 27" Belt & 6" Disc Combo Sander Figure 14. Belt sanding. Never sand the short side of any workpiece with the belt sander.
  • Page 22: Section 5: Accessories

    Available in packs of three. GRIT MODEL G1445 G4236 G1446 G4237 G1447 G4238 G4239 H7761 2" x 27" Belt & 6" Disc Combo Sander Belt Cleaners ® " x 1 " x 8 ") " x 4 " " x 8 "...
  • Page 23: Section 6: Maintenance

    Projectiles machine could cause serious Wear safety glasses at all times. H7761 2" x 27" Belt & 6" Disc Combo Sander Before Each Use: • Tighten back stop, table or guard knobs. • Replace any worn or damaged sanding discs or belts.
  • Page 24: Lubricating Sleeve Bearings

    (Figure 15). Wipe of any residual oil. Note: DO NOT apply extra oil. Too much oil can cause the belt to slip. Figure 15. Lubricating the sleeve bearings. -22- H7761 2" x 27" Belt & 6" Disc Combo Sander...
  • Page 25: Section 7: Service

    1. Not supporting the workpiece against the stop. back or vibration. 2. Starting the workpiece on a leading corner. H7761 2" x 27" Belt & 6" Disc Combo Sander Troubleshooting CORRECTIVE ACTION 1. Check power line voltage and correct if necessary.
  • Page 26: Parts Breakdown

    Parts Breakdown -24- H7761 2" x 27" Belt & 6" Disc Combo Sander...
  • Page 27: Parts List

    MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. H7761 2" x 27" Belt & 6" Disc Combo Sander Parts List PART #...
  • Page 28: Warranty And Returns

    WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
  • Page 29 ���������������������������������������������������������������������������������� � ������������������������������������������������������������������������������������ ����� ����������������������� ������ � ������������������������ ���� ��������������������� ���������������������������� ������ ������������������������ ���������� � ���������������� ���������������������������� ������������������������������� ��������������������������� ��� ��������� ����������� �� ����� �� � ��������� ������ �� ���� �� ���� ��� ��������� �������� �� ���� �� ������� ������ �������� ��� ��������� �� ������� ��� ����������� �� �������� ������������� ���...
  • Page 30 ���������������������� ���������������������� ����������������������������������� ����������������������������������� ������������������������������������� �������������������������������������� ������� ����������� ���� ���� ��� ���� ����������� �� ���������� �������������������������������������� ����� ����� ����...
  • Page 32 ��� ������ ��� ���� ���� ������� ����� ��� ������� ����� ��� �������� ��� ������� � � � ���� ����� ��� � � �������� ������ ��� � ����� ������ � �� ��� �������� ������� � ������ �������� ������ ������� ������ �� ����� ������...

Table of Contents