Setting the Time Correction Unit (TCR
Parameter)
Setting item: TCR Parameter
Setting contents:
cm (Initial setting) / inch
Sound Field Adjustment
Adjusting the Parametric Equalizer Curve
1
After selecting Parametric EQ from the Sound Field
Adjustment mode, press BANDTA to select the band to
be adjusted.
Band 1 Band 2 Band 3 Band 4 Band 5 Band 1
2
Press or to select frequency bands.
Adjustable frequency bands: 20 Hz to 20 kHz (in 1/3 octave
steps).
Band-1
Band-2
Band-3
Band-4
Band-5
3
Turn the Rotary encoder to adjust the level.
Adjustable level: −6 to +6 dB
4
Press SOURCE to set the bandwidth (Q).
Adjustable bandwidth: 1, 1.5, 3
5
To adjust another band, repeat steps 1 to 4 and adjust all
bands.
Notes
• The frequencies of adjacent bands cannot be adjusted within 4 steps.
• While adjusting the Parametric EQ, you should consider the frequency
response of the connected speakers.
Adjusting the Graphic Equalizer Curve
1
After selecting Graphic EQ from the Sound Field
Adjustment mode, press BANDTA to select the band to
be adjusted.
Band 1 Band 2 Band 3 Band 4 Band 5 Band 6
Band 7 Band 1
Band-1
Band-2
20 Hz~80 Hz (63 Hz)
50 Hz~200 Hz ( 150 Hz)
125 Hz~3.2 kHz (400 Hz)
315 Hz~8 kHz (1 kHz)
800 Hz~20 kHz (2.5 kHz)
63 Hz
150 Hz
Band-3
Band-4
Band-5
Band-6
Band-7
2
Turn the Rotary encoder to adjust the level.
Adjustable output level: −6 to +6 dB
3
To adjust another band, repeat steps 1 and 2, and then
adjust all bands.
Adjusting the Time Correction
1
After selecting T.Correction from the Sound Field
Adjustment mode, press BANDTA to select a speaker to
be adjusted.
2.2ch (3WAY) System
*1
*2
*3
F-R
R-L
R-R
F-L
Mid-L (Initial setting)
Mid-R
High-L
High-R
4.2ch (FRONT/REAR/SUBW.) System
*1
*2
*3
F-R
R-L
R-R
F-L
Front-L (Initial setting)
Front -R
Rear-L
Rear-R
2
Turn the Rotary encoder to adjust the distance correction
value (0.0 to 336.6cm).
L = (distance to farthest speaker) - (distance to other speakers)
3
Repeat steps 1 and 2 to set another speaker.
By setting these values to make its sound reach the listening
position at the same time as the sound of other speakers.
Adjusting the Crossover Settings
2.2ch (3WAY) System
1
After selecting X-Over from the Sound Field Adjustment
mode, press BANDTA to select the band to be adjusted.
NORMAL (L=R)
Setting items: LOW / MID-L / MID-H / HIGH
INDIVIDUAL (L/R)
Setting items: LOW-L / LOW-R / MID-L-L / MID-L-R /
MID-H-L / MID-H-R / HIGH-L / HIGH-R
2
Press or to select the desired cut-off frequency
(Crossover Point).
Adjustable frequency bands:
LOW / MID-L
20 Hz~200 Hz
400 Hz
1 kHz
2.5 kHz
6.3 kHz
17.5 kHz
*4
SW-L SW-R F-L
*4
SW-L SW-R F-L
33
-EN